Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Infrared and Laser Engineering

2D cold atomic beam system for increasing the loading rate of 3D MOT

Zeng Daji, 黄敏 Huang Min, 章显 Zhang Xian, 黄凯凯 Huang Kaikai, 陆璇辉 Lu Xuanhui

Published Jan 1, 2019• 1 citation
Publisher
DOI
10.3788/irla201948.0506003

Related papers

Enhanced production of 199Hg cold atoms based on two-dimensional magneto-optical trap

Ze-Xin Yu, Qixin Liu, Jianfang Sun +1 more

Efficient preparation of cold atoms plays an important role in realizing precision measurement including optical lattice clocks (OLCs). Fast preparation of cold atoms reduces Dick noise by shortening dead time in a clock interrogation cycle, which improves the stability of OLCs. Here, we increase the loading rate of the three-dimensional magneto-optical trap (3D-MOT) in the ultra-high vacuum environment by utilizing the two-dimensional magneto-optical trap (2D-MOT) with a push beam, reduce the temperature of cold atoms with the compression-MOT technique which is implemented by reducing the detuning of 3D-MOT rapidly at the end of atom preparation, and realize the enhanced production of cold atoms for 199Hg OLCs. To achieve 3D-MOT and 2D-MOT of mercury atoms, a deep ultraviolet laser (DUVL) system composed of three DUVLs is developed with one working in lower power for frequency locking and the other two in high power for laser cooling. Such a configuration improves the long-term frequency stability and shows greater robustness than our previous system consisting of two DUVLs. To maximize the 3D-MOT loading rate, we orderly optimize the detuning and the magnetic field gradient of 3D-MOT and those of 2D-MOT as well as the detuning and the power of the push beam. After all parameters are optimized, we measure the maximum loading rate of 3D-MOT to be 3.1×105 s–1 and prepare cold atoms of 1.8×106 in 9 s. The loading rate is greatly enhanced by a factor of 51 by using 2D-MOT and the push beam. In order to improve the efficiency of transferring cold atoms from 3D-MOT to optical lattice, we use compression-MOT technique to reduce the temperature of cold atoms and produce cold 199Hg atoms which are about 45 μK, lower than the expected temperature of Doppler cooling theory. By achieving the high gain of the 3D-MOT loading rate under the ultra-high vacuum and reducing the temperature of cold atoms, this enhanced preparation of cold atoms based on 2D-MOT effectively shortens the preparation time of cold atoms and improves the transfer efficiency of optical lattice, which provides a significant scheme for efficiently preparing cold mercury atoms in other experiments.

Acta Physica Sinica•Oct 9, 2023•1 citation

A multiple 2D-MOT system as a compact cold atom beam source

Jaime Ramirez-Serrano, Nathan E. Lundblad, Nan Yu +3 more

APS•May 1, 2003•0 citations

Enhanced cold mercury atom production with two-dimensional magneto-optical trap

Ye Zhang, Qixin Liu, Jianfang Sun +2 more

A cold atom source is important for quantum metrology and precision measurement. To reduce the quantum projection noise limit in optical lattice clock, one can increase the number of cold atoms and reduce the dead time by enhancing the loading rate. In this work, we realize an enhanced cold mercury atom source based on a two-dimensional (2D) magneto-optical trap (MOT). The vacuum system is composed of two titanium chambers connected with a differential pumping tube. Two stable cooling laser systems are adopted for the 2D-MOT and the three-dimensional (3D)-MOT, respectively. Using an optimized 2D-MOT and push beam, about 1.3×106 atoms, which are almost an order of magnitude higher than using a pure 3D-MOT, are loaded into the 3D-MOT for 202Hg atoms. This enhanced cold mercury atom source is helpful in increasing the frequency stability of a neutral mercury lattice clock.

Chinese Physics B•Feb 10, 2022•7 citations

A loading system for integrated atom optics

Andriy Shevchenko, Markus Hautakorpi, J. E. Lindberg +7 more

•Jan 1, 2002•0 citations

High-performance experimental apparatus for large atom number 87Rb Bose-Einstein condensates

Jiho Noh, Sung Jong Park, Chang Yong Park +3 more

We describe our high-performance experimental apparatus for producing large atom number 87Rb Bose-Einstein condensates by using a double magneto-optical trap (MOT) system that consists of a two-dimensional MOT (2D MOT) and a three-dimensional MOT (3D MOT). As an atomic beam source for loading the 3D MOT, we use a unique 2D MOT system with two-color pushing beams, which increase the loading rate and the total number of atoms in the 3D MOT, compared to a pure 2D MOT by a factor of 20. After MOT compression and polarization gradient cooling, atoms are optically pumped into a magnetically trappable hyperfine state |F = 1, m F = −1〉 to be loaded into a quadrupole-Ioffe-configuration (QUIC) trap. We enhance this optical pumping process by up to 300% by using two laser beams. After rf evaporative cooling, a Bose-Einstein condensate (BEC) with more than 2 × 107 atoms is achieved.

Journal of the Korean Physical Society•Oct 1, 2012•4 citations

High density and loading rate MOT of K atoms using a buffer-gas beam source

Maryam Hiradfar, Zack Lasner, Debayan Mitra +5 more

Bulletin of the American Physical Society•Jun 1, 2021•0 citations
Efficient preparation of cold atoms plays an important role in realizing precision measurement including optical lattice clocks (OLCs). Fast preparation of cold atoms reduces Dick noise by shortening dead time in a clock interrogation cycle, which improves the stability of OLCs. Here, we increase the loading rate of the three-dimensional magneto-optical trap (3D-MOT) in the ultra-high vacuum environment by utilizing the two-dimensional magneto-optical trap (2D-MOT) with a push beam, reduce the temperature of cold atoms with the compression-MOT technique which is implemented by reducing the detuning of 3D-MOT rapidly at the end of atom preparation, and realize the enhanced production of cold atoms for 199Hg OLCs. To achieve 3D-MOT and 2D-MOT of mercury atoms, a deep ultraviolet laser (DUVL) system composed of three DUVLs is developed with one working in lower power for frequency locking and the other two in high power for laser cooling. Such a configuration improves the long-term frequency stability and shows greater robustness than our previous system consisting of two DUVLs. To maximize the 3D-MOT loading rate, we orderly optimize the detuning and the magnetic field gradient of 3D-MOT and those of 2D-MOT as well as the detuning and the power of the push beam. After all parameters are optimized, we measure the maximum loading rate of 3D-MOT to be 3.1×105 s–1 and prepare cold atoms of 1.8×106 in 9 s. The loading rate is greatly enhanced by a factor of 51 by using 2D-MOT and the push beam. In order to improve the efficiency of transferring cold atoms from 3D-MOT to optical lattice, we use compression-MOT technique to reduce the temperature of cold atoms and produce cold 199Hg atoms which are about 45 μK, lower than the expected temperature of Doppler cooling theory. By achieving the high gain of the 3D-MOT loading rate under the ultra-high vacuum and reducing the temperature of cold atoms, this enhanced preparation of cold atoms based on 2D-MOT effectively shortens the preparation time of cold atoms and improves the transfer efficiency of optical lattice, which provides a significant scheme for efficiently preparing cold mercury atoms in other experiments.
A cold atom source is important for quantum metrology and precision measurement. To reduce the quantum projection noise limit in optical lattice clock, one can increase the number of cold atoms and reduce the dead time by enhancing the loading rate. In this work, we realize an enhanced cold mercury atom source based on a two-dimensional (2D) magneto-optical trap (MOT). The vacuum system is composed of two titanium chambers connected with a differential pumping tube. Two stable cooling laser systems are adopted for the 2D-MOT and the three-dimensional (3D)-MOT, respectively. Using an optimized 2D-MOT and push beam, about 1.3×106 atoms, which are almost an order of magnitude higher than using a pure 3D-MOT, are loaded into the 3D-MOT for 202Hg atoms. This enhanced cold mercury atom source is helpful in increasing the frequency stability of a neutral mercury lattice clock.
We describe our high-performance experimental apparatus for producing large atom number 87Rb Bose-Einstein condensates by using a double magneto-optical trap (MOT) system that consists of a two-dimensional MOT (2D MOT) and a three-dimensional MOT (3D MOT). As an atomic beam source for loading the 3D MOT, we use a unique 2D MOT system with two-color pushing beams, which increase the loading rate and the total number of atoms in the 3D MOT, compared to a pure 2D MOT by a factor of 20. After MOT compression and polarization gradient cooling, atoms are optically pumped into a magnetically trappable hyperfine state |F = 1, m F = −1〉 to be loaded into a quadrupole-Ioffe-configuration (QUIC) trap. We enhance this optical pumping process by up to 300% by using two laser beams. After rf evaporative cooling, a Bose-Einstein condensate (BEC) with more than 2 × 107 atoms is achieved.