In order to build a large-scale quantum computer, one of the requirements is high-fidelity
multiplexed qubit readout, which in turn relies on the use of ultralow-noise
amplifiers. While Josephson Parametric Amplifiers (JPAs), using a cavity with
few Josephson junctions, have shown promising results for single qubit readout,
they have limitations such as low saturation power and a gain-bandwidth product
restriction. This makes them less suited for frequency multiplexed qubit readout. A
current-pumped Josephson Travelling-Wave Parametric Amplifier (JTWPA), using
4-wave mixing in a lumped-element transmission line, features both high saturation
power as well as no restriction on large bandwidth and high gain. This is possible
due to multiple junctions and the lack of a cavity. However, also this current pumped
JTWPA has an inherent problem, namely phase mismatch between the pump and
the signal. This prevents exponential gain. In this thesis, a current pumped JTWPA
using the resonant phase matching (RPM) technique to reduce the phase mismatch
problem is studied and characterised. The JTWPA shows high gain, high saturation
power and a large signal-to-noise ratio improvement. The JTWPA is also used for
qubit readout, for which it clearly improves the readout fidelity.
In order to build a large-scale quantum computer, one of the requirements is high-fidelity
multiplexed qubit readout, which in turn relies on the use of ultralow-noise
amplifiers. While Josephson Parametric Amplifiers (JPAs), using a cavity with
few Josephson junctions, have shown promising results for single qubit readout,
they have limitations such as low saturation power and a gain-bandwidth product
restriction. This makes them less suited for frequency multiplexed qubit readout. A
current-pumped Josephson Travelling-Wave Parametric Amplifier (JTWPA), using
4-wave mixing in a lumped-element transmission line, features both high saturation
power as well as no restriction on large bandwidth and high gain. This is possible
due to multiple junctions and the lack of a cavity. However, also this current pumped
JTWPA has an inherent problem, namely phase mismatch between the pump and
the signal. This prevents exponential gain. In this thesis, a current pumped JTWPA
using the resonant phase matching (RPM) technique to reduce the phase mismatch
problem is studied and characterised. The JTWPA shows high gain, high saturation
power and a large signal-to-noise ratio improvement. The JTWPA is also used for
qubit readout, for which it clearly improves the readout fidelity.
Quantum-limited parametric amplifiers have become increasingly interesting and relevant with the progressing field of quantum computing. However, currently it is still challenging to fabricate these complex devices. In this thesis, we developed cross type Josephson junctions (JJs), lumped element LC resonators, lumped element Josephson parametric amplifiers (JPAs) and Josephson traveling wave parametric amplifiers (JTWPAs). We found and resolved several fabrication issues however we suspect that both the JPA and JTWPA suffered from microshorts in the circuits during the cryogenic measurements. Nevertheless, we managed to measure the resonance frequency of the JPA and have noticed the flux focusing effect when we flux tune it. We preformed room temperature measurements on over 300 JJs and calculated the relative standard deviation (RSD) for various JJ sizes. We found the spread of 30 fabricated resonators and a rough estimate of their Q factors. The JTWPAs developed are non-degenerate four wave mixing amplifiers that use the resonant phase matching (RPM) technique to reduce the phase mismatch problem. The transmission through the measured JTWPA showed 50 dB loss probably caused by presumably a short from the transmission line to ground. However, when the JTWPA was driven with a pump we observed 20 dB increase in transmission in some frequency bands.
Abstract A Josephson traveling-wave parametric amplifier (JTWPA) is indispensable for the high-fidelity readout of superconducting qubits, owing to its broadband gain and near-quantum-limited noise performance. Conventional JTWPAs implemented with 0-Josephson junctions (0-JTWPAs) avoid magnetic-flux bias but rely on Kerr nonlinearity, which leads to pump-power-dependent phase mismatch, gain ripple, and a limited dynamic range. More recently, three-wave-mixing (3WM) JTWPAs employing flux-biased rf-SQUIDs have been proposed to suppress Kerr effects. However, these designs require a significant external flux bias per unit cell, which complicates cryogenic hardware, introduces sensitivity to flux noise, and limits scalability in large arrays. In this study, we propose and analyze a π -junction-based JTWPA ( π -JTWPA) in which the intrinsic π phase shift of the junction effectively displaces the operating point of the current–phase relation. This approach aims to realize 3WM-type nonlinearity with reduced flux bias while preserving broadband amplification, thereby simplifying flux-bias distribution, enhancing robustness against flux noise, and providing a pathway toward scalable, multiplexed quantum readout architectures. In addition, we examine the potential applicability of the π -JTWPA in four-wave-mixing (4WM) operation.
Recent progress in physics has increased the necessity for ultra-low noise amplifiers capable of operating at the quantum limit performance. These amplifiers are essential to enhance astronomical detection, dark-matter search, and qubit readout in quantum computing, among other applications. Superconducting Josephson junction Travelling Wave Parametric Amplifiers (JTWPAs) operated in the microwave range, have demonstrated high gain over several gigahertz (GHz) bandwidth, with quantum-limited noise performance and minimal heat dissipation. These excellent properties make JTWPAs an ideal solution for ultra-low noise amplification. This thesis delves into the design, fabrication and characterisation of JTWPAs operated in the microwave (1-16 GHz) and the W-band (70-115GHz) regimes. A generalised coupled-mode equations (CME) framework describing JTWPAs based on Josephson junctions and DC superconducting quantum interference devices (SQUIDs) is introduced. This framework can be combined with electromagnetic (EM) simulation softwares to model the JTWPAs, facilitating their design. It is therefore used to model two microwave JTWPA designs, using parallel plate capacitors (PPCs) and interdigitated capacitors (IDCs). The fabrication and characterisation of both designs are presented, and possible fabrication and design issues are carefully discussed. Despite these issues, we observed broadband gain in the JTWPA with PPCs, achieving > 20 dB gain at several frequency points, and a measured P1dB = −95.8dBm when operated at 17.3 dB. The RF properties of a 500-junction Josephson array are also presented in this manuscript. The device creates a Fabry-Perot cavity, leading to non-travelling wave parametric effects, such as narrow-band gain. We also observed indications of efficient phase-sensitive amplification. The thesis is concluded with the first — to the best of our knowledge — experimental attempt to extend the operational frequency of a JTWPA to the W-band. The novel design, fabrication techniques and characterisation of the W-band JTWPA are discussed in detail in this manuscript, leading to promising results suggesting that JTWPA could operate at high frequencies.
Advancing error-corrected quantum computing and fundamental science necessitates quantum-limited amplifiers with near-ideal quantum efficiency and multiplexing capability. However, existing solutions achieve one at the expense of the other; for example, Josephson traveling wave parametric amplifiers (JTWPAs) are highgain, broadband, and chip-based quantum amplifiers that conventionally incur a bandwidth-noise tradeoff. When operated at 20-dB gain and instantaneous bandwidths of a few GHz, JTWPAs typically reach near-quantum limited intrinsic efficiencies of 70% - 85% relative to that of an ideal phase-preserving quantum amplifier. This is due to information leakage to the sidebands of the JTWPA, which can be recovered by adiabatically transforming the input modes to Floquet modes of the system within the device. In this thesis, we experimentally demonstrate the first Floquet-mode travelingwave parametric amplifier (Floquet TWPA). Fabricated in a superconducting qubit process, this Floquet TWPA achieves minimal dissipation, quantum-limited noise performance, and broadband operation. Our device exhibits > 20-dB amplification over a 3-GHz instantaneous bandwidth, <0.5 -dB average in-band insertion loss, and the highest-reported intrinsic quantum efficiency for a TWPA of 92.1±7.6%, relative to an ideal phase-preserving amplifier. When measuring a superconducting qubit, our Floquet TWPA enables a system measurement efficiency of 65.1 ± 5.8%, the highest-reported in a superconducting qubit readout experiment utilizing phase-preserving amplifiers to the best of our knowledge. Finally, we discuss the noise limitations of our current experimental setup, as well as impedance matching strategies that will enable us to push towards ideal JTWPA performance. These general-purpose Floquet TWPAs are suitable for fast, high-fidelity multiplexed readout in large-scale quantum systems and future monolithic integration with quantum processors.
Bringing signals from quantum to classical, from few-photon to many-photon levels for further processing, is a common challenge in rising quantum technologies. These include quantum computing, quantum communication, quantum sensing, radio astronomy, and dark matter searches, typically operating at microwave frequencies and millikelvin temperatures. Superconducting parametric amplifiers, as the first piece in the readout chain, have become a cornerstone of these technologies, since they offer unrivaled noise performance near the quantum-mechanical limit and high gain to surpass the noise of subsequent amplifiers. A notable implementation is the Josephson traveling-wave parametric amplifier (TWPA), which stands out due to its bandwidth of several Gigahertz and high saturation power, often larger than -100 dBm. These key properties come at the cost of complexity in design and fabrication: TWPA metamaterials often contain several thousands of Josephson junctions. Designing high-gain TWPAs involves three major challenges: ensuring impedance-matching, phase-matching of parametric amplification, and suppressing unwanted processes, all achievable through sub-wavelength dispersion engineering. This thesis covers the circuit design and analysis, implementation, and experimental characterization of a dispersion-engineered TWPA based on radio-frequency superconducting interference devices (rf-SQUIDs). It focuses on a detailed investigation of dispersion-engineering techniques and their effects on amplifier performance, particularly through the use of time-domain circuit simulations to analyze the multimode dynamics of the circuit. The experimentally realized device features 18 dB of gain, an instantaneous bandwidth spanning from 2.2 to 6.7 GHz, a system noise of 2.5 quanta, and a saturation power of (−86.5 ± 4.0) dBm. With these characteristics, it is suitable for frequency-multiplexed readout of detector arrays or qubits. Its high saturation power, about 10 dB higher than other reported Josephson-junction-based TWPAs, allows increasing the number of qubits per readout line, or decreasing the intermodulation between frequency-multiplexed qubits, both crucial for scaling up quantum computation.
Josephson junction based parametric amplifiers are used to read out the state of superconducting qubits with high fidelity. These amplifiers are themselves superconducting circuits operating at temperatures of tens of millikelvin. A version of this type of amplifier which has exhibited large bandwidth and saturation power is the Josephson traveling wave parametric amplifier (JTWPA). One particular JTWPA topology consists of hundreds to thousands of Josephson junctions in a transmission line configuration along with periodic phase matching resonators to increase gain. Here, we look at using a superconducting qubit fabrication process to realize this circuit To analyze the sensitivity of the JTWPA to fabrication process variation, we discuss a linear model for the circuit which takes into account unit cell to unit cell variation. To extract the measured circuit values, we use in-situ measurements of a JTWPA to compare the designed values to the realized values. Finally we discuss preliminary results realizing an example JTWPA design using a fabrication process designed for superconducting qubits.