The development of an experimental apparatus to produce Bose-Einstein condensates (BECs) of ⁸⁷Rb atoms and their application to magnetometry are discussed. Optical detection of atomic Larmor precession is a widely explored method for high-sensitivity measurements of magnetic fields. In this context, short laser/atom interaction time, atomic thermal diffusion and decoherence effects are among the main limitations. In this thesis, we overcome such problems by using spin-polarised ⁸⁷Rb ultra-cold atoms as the sensing element. After the atoms are polarised, a resonant pulse of radio-frequency excites Larmor precession, which is sensitive to external magnetic fields. By measuring the perturbations of the radio-frequency induced spin precession, information on the magnetic fields of interest. This is achieved by monitoring the polarisation plane’s rotation of a linearly polarised resonant laser probe. In the first part of this thesis, the building and optimisation of a laser-cooling set up to obtain a BEC in a hybrid trap is reported. In order to achieve the Phase Space Density (PSD) required for BEC, several different stages of trapping and cooling are necessary. Each phase has been implemented and optimised. The first step consists in the magneto-optical trap (MOT). Here a velocity dependent damping force and a spatially dependent confining force give the largest changes in PSD. Then atoms are loaded into a hybrid trap obtained by overlapping a quadrupole magnetic potential and a far detuned optical crossed dipole trap. The final stage for the condensation consists of forced evaporative cooling, both via magnetic and optical evaporation. In the second part of the thesis, a general overview of the principles of optical atomic magnetometry is provided and the advantages of using ultra-cold atoms with respect to conventional thermal vapours are discussed. The implementation, operation and a preliminary characterisation of the ultra-cold atom magnetometer are described along with the preliminary results collected. Finally, a plan for future improvements of its sensitivity is presented.
The development of an experimental apparatus to produce Bose-Einstein condensates (BECs) of ⁸⁷Rb atoms and their application to magnetometry are discussed. Optical detection of atomic Larmor precession is a widely explored method for high-sensitivity measurements of magnetic fields. In this context, short laser/atom interaction time, atomic thermal diffusion and decoherence effects are among the main limitations. In this thesis, we overcome such problems by using spin-polarised ⁸⁷Rb ultra-cold atoms as the sensing element. After the atoms are polarised, a resonant pulse of radio-frequency excites Larmor precession, which is sensitive to external magnetic fields. By measuring the perturbations of the radio-frequency induced spin precession, information on the magnetic fields of interest. This is achieved by monitoring the polarisation plane’s rotation of a linearly polarised resonant laser probe. In the first part of this thesis, the building and optimisation of a laser-cooling set up to obtain a BEC in a hybrid trap is reported. In order to achieve the Phase Space Density (PSD) required for BEC, several different stages of trapping and cooling are necessary. Each phase has been implemented and optimised. The first step consists in the magneto-optical trap (MOT). Here a velocity dependent damping force and a spatially dependent confining force give the largest changes in PSD. Then atoms are loaded into a hybrid trap obtained by overlapping a quadrupole magnetic potential and a far detuned optical crossed dipole trap. The final stage for the condensation consists of forced evaporative cooling, both via magnetic and optical evaporation. In the second part of the thesis, a general overview of the principles of optical atomic magnetometry is provided and the advantages of using ultra-cold atoms with respect to conventional thermal vapours are discussed. The implementation, operation and a preliminary characterisation of the ultra-cold atom magnetometer are described along with the preliminary results collected. Finally, a plan for future improvements of its sensitivity is presented.
This thesis presents advancements in radio-frequency atomic magnetometry utilising cold atoms as sensors. While cold atom magnetometers demonstrate lower absolute sensitivity compared to conventional vapour cell systems due to reduced atom numbers, they offer exceptional spatial resolution at the micrometre scale. The experimental apparatus features a cold atom production system capable of reaching quantum degeneracy through a refined cooling sequence that involves optical molasses, magnetic trapping and evaporation, and optical evaporative cooling in the dipole trap, culminating in a 87Rb Bose-Einstein condensate. This work details the development and characterisation of magnetometer set-ups with progressively enhanced performance. The first magnetometer utilised atoms in the optical molasses phase as a sensor, achieving an AC sensitivity of 330 pT/√Hz with approximately 108 atoms at 20 μK. Comprehensive magnetometry optimisation methods were developed to enhance sensitivity. Following laboratory interruptions due to the COVID-19 pandemic, system rebuilding incorporated significant upgrades, including a new probe laser and gradient compensation systems. The improved magnetometer prototype achieved a substantially enhanced sensitivity of 0.72±0.33 pT/√Hz, approaching the fundamental sensitivity limit of the system. Using atoms in the magnetic trap as a sensor, a sensitivity of 1.85 pT/√Hz was demonstrated. The system was verified to be photon-shot noise limited. Investigations into a double-pass probe configuration showed that, while the measured sensitivity was similar to that of the single-pass (4.3 pT/√Hz compared to 3.1 pT/√Hz at a probe power of 6.4 μW measured at the detector), the rotation angle increased by a factor of 2.2, with significantly reduced noise levels. These findings suggest that multi-pass strategies hold promise for enhanced performance in future implementations. In addition, the first signal detection from a BEC magnetometer, achieving 4.5 nT/√Hz with only 95,000 atoms at 35 nK was demonstrated.
This thesis describes the design, construction and optimisation of a new apparatus to produce Bose-Einstein condensates (BECs) of 87Rb atoms. The main aim in building this system was to include a high resolution imaging system capable of resolving single atoms. Optical access for the imaging system was created by including a stage of atom transport in which the atoms are magnetically transferred ~50 cm from a magneto-optical trap (MOT), where they are initially collected, to a glass science cell where experiments are carried out and imaging takes place. Two magnetic transport schemes have been demonstrated, based on approaches first used in other laboratories. First, a scheme in which the atoms are transferred in a moving pair of magnetic trapping coils. Second, a hybrid scheme where the atoms are translated part of the distance in the moving coils, and the rest of the way by switching the current in a chain of fixed coils. This second scheme was designed to allow optical access for a high numerical aperture microscope objective to be placed immediately next to the science cell for high resolution imaging.The atoms were first collected in a large pyramid MOT which can be loaded with 3 × 10^9 atoms in a time of 20 s. Around half of these atoms – those in the |F = 1, mF = −1> magnetic substate – were then magnetically trapped prior to transport. The typical fraction of the trapped atoms transferred to the science cell was ~30% and ~18% for the moving coils and hybrid schemes respectively.Evaporative cooling was carried out on the atom cloud following transport with the moving coils and loading into a time-orbiting potential trap. The optimised cooling sequence lasted for 28 s and consistently produced a pure condensate with 5 × 10^5 atoms. A BEC has also been produced by evaporative cooling following hybrid transport. The next experimental steps will be to optimise the hybrid transfer approach further and install the high resolution imaging system.The system is well-placed to continue an ongoing series of experiments in which ultracold atoms are trapped in RF-dressed potentials. These potentials will be used to study low-dimensional quantum gases as well as in experiments where small atom number BECs are rapidly rotated to enter the fractional quantum Hall regime.
Spinor Bose-Einstein condensates (BECs) are multi-component superfluids with magnetic interactions, formed from dilute gases of atoms in the Zeeman sublevels mF of a single hyperfine ground state F. Spinor BECs are inherently magnetic quantum objects, and exhibit a multitude of features such as spin domains, magnon excitations, and distinct magnetic phases. At the heart of the magnetic nature of a spinor BEC is the spin-dependent collisional interaction c, which determines the overall magnetic behaviour of the superfluid. In conjunction with the quadratic Zeeman shift q, the magnitude and sign of c give rise to an intricate magnetic phase diagram. The magnetic phase of a spinor BEC is tunable, and c and q are the knobs. In addition to realising quantum simulators of magnetism, spinor BECs are also precise magnetic sensors. Atomic magnetometry measures the Larmor precession frequency of atoms, which is proportional to the magnetic field strength. The sensitivity of an atomic magnetometer is principally dependent on the duration of the measurement (interrogation time) and number of atoms participating in the measurement. BECs are highly suitable as atomic magnetometers, allowing for long interrogation times and high atomic density, with microscopic sensor volumes. The latter is an important consideration, as measurement of small magnetic sources demand equally microscopic sensors. Established forms of magnetometry (such as warm vapour magnetometers) use large sensing volumes and are not trivially miniaturised. The exquisite sensitivity of a spinor BEC to magnetic fields becomes a liability when one studies low energy (~ 1 Hz) spinor physics over long evolution times (100 ms) in a typical laboratory environment. To first order, the spin-collisional interaction is independent of the magnetic field. However, spatially inhomogeneous magnetic fields are problematic, exerting mechanical forces on the magnetically sensitive spin components, suppressing spin collisions and possibly introducing relaxation mechanisms that confound the observation of intrinsic equilibration. Precise characterisation of magnetic field gradients and their cancellation is thus of paramount importance. In this thesis, the interaction of a spinor BEC with its environment is studied. The construction, operation and optimisation of a BEC machine is described in detail, as well as the quantum state preparation and control techniques used. Spin-mixing collisions were studied by observing population oscillations, the characteristic hallmark of such coherent phenomena. The observed population dynamics showed strong evidence of the deleterious effects of magnetic field gradients. A series of experiments were performed using spin-echo pulse sequences to decouple the evolving spinor condensate from the inhomogeneous magnetic environment with encouraging results, but which posed further questions. The fidelity of spin-echo pulses in the strong radiative coupling regime was also studied. Spinor condensates were then employed as sensitive magnetometers to characterise the magnetic landscape they inhabit. A new method of measuring magnetic field gradients was developed, using a pair of spinor BECs separated in space that are simultaneously addressed by a Ramsey interferometry sequence. Combined with a re-orientable magnetic bias field, the resulting gradiometer was used to measure the magnetic field gradient tensor in vacuo. This scheme can be extended to realise a high-precision vector co-magnetometer, with spatiotemporal sensitivity comparable to established forms of magnetometry. Vector light shifts (VLSs) are optically-induced energy shifts that result in effective magnetic fields, which in our case originate from the laser beams used to trap the atoms. The VLS vanishes for purely linearly polarised light, which is experimentally difficult to obtain in vacuo. Small elliptical polarisation imperfections originating from birefringent optics and the glass vacuum cell result in a non-zero shift that contaminates magnetometry measurements. The VLS is spatially varying due to the intensity gradient of the trapping light. Due to gravitational sag of the trapping potential, the spatial variation of the VLS is accentuated, resulting in an effective magnetic field gradient that contributes to dephasing and component separation. The simultaneous Ramsey interferometry experiments are then adapted to measure the VLS-induced Zeeman shift and diagnose its elimination. Up to 99.96% of the VLS is eliminated using this method, and extensions to the technique are described.
The long term aim of the work is to study non-equilibrium and symmetry-breaking phenomena for a Bose-Einstein condensate in time-dependent optical traps. The work presented in this thesis is mostly devoted to the design, construction and testing of the apparatus, in which condensation was successfully achieved. The first part of this thesis describes the design and construction of a hybrid setup for the production of a Bose-Einstein condensate (BEC) of 87 Rb in the |F = 2, m F = +2 > state. The vacuum system is composed of a first chamber, where a low-velocity intense source (LVIS) of atoms is produced to provide a pre-cooled atomic beam to the science chamber, where the magneto-optical trap (MOT) is produced, trapping more than 3 x 10 8 atoms at a temperature of roughly 400 μK. Forced radio- frequency evaporation is performed in a quadrupole magnetic trap and the atoms are transferred to a hybrid far-detuned optical trap in a crossed-beams configuration; evaporation in the optical potential leads to reliable production of a BEC every 50 s, composed of 10^5 atoms at a temperature of 10-30 nK. To ensure fine control on the optical potential depth and high intensity and pointing stability, a stabilisation system has been developed and characterised. The second part of this thesis describes the realisation of a 1D optical lattice, produced by two phase-locked laser beams emitting at 780 nm, with a red detuning of approximately 3.5 GHz, in counter-propagating configuration. Oscillating forces obtained by phase-modulating the optical potential are applied.
This thesis describes the design, construction and optimisation of two compact \nsetups to produce ⁸⁷Rb Bose-Einstein condensates and dual ⁷Li-⁸⁷Rb Magneto-Optical Traps (MOTs). The motivation for compact systems is to have simplified \nsystems to cool the atoms. The first experimental setup is based on a single pyrex \nglass cell without the need for atom chips. Fast evaporation will be achieved in a hybrid trap comprising of a magnetic quadrupole trap and an optical dipole trap \ncreated by a Nd:YVO4 laser and with future plans of using a Spatial Light Modulator \n(SLM). To enhance an efficient and rapid evaporation, we have investigated Light-Induced Atomic Desorption (LIAD) to modulate the Rb partial pressure during the cooling and trapping stage. With this technique, a ⁸⁷Rb MOT of 7 x 10⁷ atoms was loaded by shining violet light from a LED source into the glass cell, whose walls are coated with rubidium atoms. The atoms were then cooled by optical molasses and then loaded into a magnetic trap where lifetime measurements demonstrated that LIAD improves on magnetically-trapped atoms loaded from constant background pressure by a factor of six. This is quite encouraging and opens the possibility to do a rapid evaporation. In a second experiment, we have designed a compact system based on a stainless steel chamber to trap either ⁷Li or ⁶Li atoms in a MOT loaded from alkali-metal dispensers without the need of conventional oven-Zeeman slower. This setup can also load ⁸⁷Rb atoms, allowing future projects to simultaneously produce degenerate quantum gases of bosonic ⁸⁷Rb and fermionic ⁶Li atoms.
The possibility to mould and control pure quantum systems has been offered by the experimental observation of Bose-Einstein condensation, a unique phase of matter when macroscopic quantities of a gas occupy the lowest quantum state. Techniques for creating these degenerate gases vary from laboratory to laboratory; each offers an unique test bed for studying quantum physics on a macroscopic scale. This thesis reports on the experimental design, construction and performance of an apparatus to create two-component 87Rb and 41K condensates for studies of non-equilibrium dynamics. This thesis is broken down as follows. In Chapter 1, a brief overview of the history and status of Bose Einstein condensates is presented, to affirm the motivation behind our work. Chapter 2 then presents the fundamental theory and background information to understand how and why our experiment was built. Chapter 3 describes the bulk of the work undertaken at the beginning of this thesis. In particular it describes the design choices, construction and performance of the vacuum, and laser and magnetic coil systems that are the key structural elements of the apparatus. In particular the vacuum system is a two-component differentially pumped system designed to optimise the number and lifetime of trapped atoms. Another integral element of the vacuum chamber is the science cell that enables high optical access, and close physical, access to an atomic cloud. As a result, high resolution imaging, ≃ 980 nm resolution at 780 nm is expected with a commercial microscope objective lens. The laser system is carefully de- signed to best combine and deliver the seven different optical frequencies required to simultaneously trap and manipulate 87Rb and 41K atoms. The magnetic coil system also represents an integral component of the apparatus, responsible for trapping and transferring atoms in a quadrupole field. One pair of coils is able to have their current direction reversed in order to generate bias fields. This allows access to Feshbach resonances between the two species, once they have been condensed. The second part of this thesis, Chapter 4, describes the performance of the apparatus when used to simultaneously trap 41K and 87Rb in the 3D magneto- optical trap (MOT) and produce a condensate of 87Rb atoms. In particular 1 × 109 rubidium atoms are routinely trapped in the 3D-MOT and transferred to the science chamber. In the hybrid trap the atoms are evaporatively cooled via microwave radiation, later to be used to sympathetically cool 41K, and loaded into a hybrid optical dipole and magnetic trap. At this stage ≃ 5 × 106 atoms are evaporatively cooled, by lowering the trap depth of the optical dipole beam, until a condensate of 87Rb is formed, containing 1.5 × 105 atoms. Additionally we are able to produce 3D MOTs of 41K simultaneously with the 87Rb 3D MOTs.