PhD Thesis: Superconducting circuit quantum electrodynamics (QED) has developed into a powerful platform for studying the interaction between matter and different states of light. In this context, superconducting quantum bits (qubits) act as artificial atoms interacting with quantized modes of the electromagnetic field. The field can be trapped in superconducting microwave resonators or propagating in transmission lines. In this thesis, we particularly study circuit QED systems where microwave fields are coupled with superconducting flux and transmon qubits. We optimize the coherence properties of the resonators, by analyzing loss mechanisms at excitation powers of approximately one photon on average. We find that two-level fluctuators associated with oxide layers at substrate and metal surfaces and metal-metal interfaces represent the predominant loss channel. Furthermore, we show how broadband thermal photon fields influence the relaxation and dephasing properties of a superconducting transmon qubit. To this end, we study several second-order loss channels of the transmon qubit and find that the broadband fields introduce a larger decay rate than expected from the Purcell filter defined by the resonator. Additionally, we show that qubit dephasing at the flux-insensitive point as well as low-frequency parameter fluctuations can be enhanced by thermal fields. Finally, we study how artificial atoms react to changes in inherent properties of the light fields. We perform a detailed analysis of the photon statistics of thermal fields using their relation to the qubits coherence properties. We quantitatively recover the expected $n^{2}\,{+}\,n$-law for the photon number variance and confirm this result by direct correlation measurements. We then show a novel technique for the in-situ conversion of the interaction parity in light-matter interaction. To this end, we couple spatially controlled microwave fields to a flux qubit with two degrees of freedom.
PhD Thesis: Superconducting circuit quantum electrodynamics (QED) has developed into a powerful platform for studying the interaction between matter and different states of light. In this context, superconducting quantum bits (qubits) act as artificial atoms interacting with quantized modes of the electromagnetic field. The field can be trapped in superconducting microwave resonators or propagating in transmission lines. In this thesis, we particularly study circuit QED systems where microwave fields are coupled with superconducting flux and transmon qubits. We optimize the coherence properties of the resonators, by analyzing loss mechanisms at excitation powers of approximately one photon on average. We find that two-level fluctuators associated with oxide layers at substrate and metal surfaces and metal-metal interfaces represent the predominant loss channel. Furthermore, we show how broadband thermal photon fields influence the relaxation and dephasing properties of a superconducting transmon qubit. To this end, we study several second-order loss channels of the transmon qubit and find that the broadband fields introduce a larger decay rate than expected from the Purcell filter defined by the resonator. Additionally, we show that qubit dephasing at the flux-insensitive point as well as low-frequency parameter fluctuations can be enhanced by thermal fields. Finally, we study how artificial atoms react to changes in inherent properties of the light fields. We perform a detailed analysis of the photon statistics of thermal fields using their relation to the qubits coherence properties. We quantitatively recover the expected n2+n-law for the photon number variance and confirm this result by direct correlation measurements. We then show a novel technique for the in-situ conversion of the interaction parity in light-matter interaction. To this end, we couple spatially controlled microwave fields to a flux qubit with two degrees of freedom.
Waveguide circuit quantum electrodynamics (waveguide circuit QED) studies light-matter interaction with superconducting circuits in one dimension. In circuit QED, natural atoms are replaced by superconducting qubits consisting of a non-linear Josephson junction, resulting in an anharmonic energy spectrum just like real atoms. With superconducting qubits, it is possible to study quantum optical phenomena and reach new regimes hard to achieve with real atoms due to weak coupling to the electromagnetic field. The reduction to one dimension in waveguide QED increases the electromagnetic field's directionality, which results in reduced losses. In this thesis, we first introduce circuit quantisation, giving the basis for the next part, where we investigate a transmon, a charge-insensitive artificial atom, coupled to a semi-infinite transmission line. An atom coupled to a semi-infinite waveguide is referred to as an atom in front of a mirror and is the subject of all appended papers. We proceed by summarising Paper I and III's main results: in Paper I, we investigate the spontaneous emission of a transmon coupled to a semi-infinite transmission line, where we take time-delay effects into account. We find that the system dynamics strongly depend on the coupling strength to the transmission line and the atom's position with respect to the electromagnetic field, leading to the Purcell effect or the convergence to a dark state with finite excitation probability. In the high-impedance regime, which we investigate in Paper III, the properties of the transmon coupled to the high-impedance transmission line change drastically. It becomes highly reflective and creates its own cavity with the mirror, resulting in the emergence of cavity modes and vacuum Rabi oscillations in the spontaneous emission dynamics. In the next chapter of the thesis, we demonstrate how to quantise an electromagnetic field and derive a light-matter interaction Hamiltonian within dipole approximation. We then give an introduction to open quantum systems and derive the quantum-optical master equation in Lindblad form. Furthermore, we introduce the dressed state picture, where the interaction of light and matter is so strong that the individual energy levels of light and matter are no longer separable. Both the quantum optical master equation and the dressed state picture are relevant in Paper II and IV. In Paper II, an experimental collaboration, we perform several experiments to characterise and discriminate different decay rates of a superconducting qubit coupled to the end of a transmission line. One experiment measured the atomic fluorescence spectral density, which shows an asymmetry for off-resonant driving, resulting from pure dephasing: an effect that we explain in more detail in this thesis and Paper II. In Paper IV, we theoretically investigate amplification mechanisms realised by different set-ups of an atom coupled to a semi-infinite waveguide. In the considered systems, the amplification of a probe field happens either due to population inversion between the pure states or dressed states or multi-photon processes. We find that compared to an open waveguide, we can achieve a higher gain in the amplification with a semi-infinite waveguide.
In the last decade, the field of Quantum Optics has been enriched with a completely new platform: superconducting quantum circuits, also known as circuit-QED. This platform builds on the original designs of superconducting qubits, that is few-level systems made of superconducting islands and Josephson junctions, but adds to it a new ingredient, microwave photons. In this talk I will review circuit-QED with a focus on two complementary lines of research: ultrastrong light-matter coupling and strongly correlated propagating photons. The first topic deals with novel designs of superconducting qubits, engineering their coupling to the microwave radiation field to reach Rabi frequencies that approach the qubit and photon frequencies. In this regime, known as ”ultrastrong coupling”, the rotating wave approximation from Quantum Optics is no longer valid, the vacuum may spontaneously polarize, producing photons that get bound to the qubit, and novel physics is expected to emerge. I will review recent experiments on this topic, together with various theoretical proposals to tame this ultrastrong coupling. The second topic revolves around the notion of ”propagating” photons in these circuits. Most experiments in circuit-QED so far adopted the typical configuration of artificial atoms (qubits) interacting with artificial cavities (LC resonators). This proved useful in order to reach the strong coupling regime, demonstrating Rabi oscillations and developing a variety of protocols for quantum information, tomograhy, entanglement, etc. However, recent experiments have shown that it is possible to also work with propagating photons, replacing the LC resonators with open transmission lines, and studying the scattering properties of those artificial atoms. In this context we have worked on developing new technology to detect and control these photons, engineering single-photon detectors, quantum metamaterials and photonic crystals, or even new nonlinear media based on coupled cavities.
The past 20 years has seen rapid developments in circuit quantum electrodynamics, where superconducting qubits and resonators are used to control and study quantum light-matter interaction at a fundamental level. The development of this field is strongly influenced by quantum information science and the prospect of realizing quantum computation, but also opens up opportunities for combinations of different physical systems and research areas. Superconducting circuits in the microwave domain offer a versatile platform for interfacing with other quantum systems thanks to strong nonlinearities and zero-point fluctuations, as well as flexibility in design and fabrication. Hybrid quantum systems based on circuit quantum electrodynamics could enable novel functionalities by exploiting the strengths of the individual components.This thesis covers experiments coupling superconducting circuits to surface acoustic waves (SAWs), mechanical waves propagating along the surface of a solid. Strong coupling can be engineered using the piezoelectric properties of GaAs substrates, and our experiments exploit this to investigate phenomena in quantum field-matter interaction. A key property of surface acoustic waves is the slow propagation speed, typically five orders of magnitude slower than light in vacuum, and the associated short wavelength. This enables the giant atom regime where the artificial atom in the form of a superconducting circuit is large compared to the wavelength of interacting SAW radiation, a condition which is difficult to realize in other systems. Experiments described in this thesis use these properties to demonstrate electromagnetically induced transparency for a mechanical mode, as well as non-Markovian interactions between an artificial giant atom and the SAW field. When the SAW field is confined to a resonant cavity, the short wavelength allows multimode spectra suitable for interacting with a frequency comb. We use a multimode SAW resonator to characterize the ensemble of microscopic two-level system defects with a two-tone spectroscopy approach. Finally, we introduce a hybrid superconducting-SAW resonator with applications in quantum information processing in mind. Experiments with this device demonstrate entanglement of SAW modes, and show promising results on the way to engineer cluster states for quantum computation in continuous variables.
Controlling Photons in Superconducting Electrical Circuits Blake Robert Johnson 2011 Circuit quantum electrodynamics (circuit QED) is a system that allows for strong coupling between microwave photons in transmission line cavities and superconducting qubits or artificial atoms. While circuit QED is often studied in the context of quantum information processing, it also provides an attractive platform for performing quantum optics experiments on-a-chip, because the level of control and coupling strengths available in circuit QED opens a vast array of possibilities for the creation, manipulation, and detection of quantum states of light. In this thesis, the extension of circuit QED to two cavities is examined, including design issues for cavities with very different Q-factors, and a new qubit design is proposed that couples to both cavities. The qubit-cavity interaction, while providing much of the utility of circuit QED, also introduces additional qubit relaxation. A powerful formalism for calculating this energy decay due to the classical admittance of the electromagnetic environment is presented in the context of circuit QED. Measurements of a wide range of samples validate this theory as providing an effective model for relaxation. A new circuit element, called the ‘Purcell filter’, is introduced and demonstrated to decouple the relationship between cavity Q and qubit relaxation. Finally, a new method for performing quantum nondemolition measurements of microwave photons is demonstrated. Controlling Photons in Superconducting Electrical Circuits A Dissertation Presented to the Faculty of the Graduate School of Yale University in Candidacy for the Degree of Doctor of Philosophy by Blake Robert Johnson Dissertation Director: Professor Robert J. Schoelkopf
Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.
Artificially engineered atoms, built using superconducting electrical circuits, have had a broad impact on the field of quantum information and quantum computing. Based on the Josephson effect, superconducting qubits have provided a robust platform for engineering light-matter interactions at the single-photon level. The ability to precisely control and manipulate single photons using superconducting qubits and cavities, a field now popularly known as circuit quantum electrodynamics (circuit QED), has enabled new and novel regimes in quantum physics, which previously remained inaccessible. For instance, the coupling between individual photons and artificial atoms have been shown to reach the ultrastrong and deep-strong regimes, a feat which is difficult to achieve with natural atoms. The superconducting circuit platform is now a promising contender for building large-scale quantum processors, attracting large investments from academic, industry and government players. \n \nThis thesis uses superconducting circuits to engineer photon interactions in two separate studies. The first is aimed at studying the physics of ``giant" artificial-atoms. The second study explores the route towards building a quantum heat engine using two parametrically-coupled, superconducting microwave cavities. We review the theoretical ideas and concepts which motivate our work, along with discussions of the design methodology, simulations, fabrication, measurement setup and the experimental findings. \n \nIn the first study, we explore a giant artificial atom, formed from a transmon qubit, which is coupled to propagating microwaves at multiple points along an open transmission line. The multipoint coupling nature of the transmon allows its radiated field to interfere with itself leading to some striking ``giant" atom effects. For instance, we observe strong frequency dependent couplings of the transmon's transition levels to its electromagnetic environment, a feature which is not observed with ordinary artificial atoms. We measure large on/off ratios, as high as 380, for the coupling rate of the ket0−ket1 transition. Furthermore, we show that we can enhance or suppress the coupling rate of the ket1−ket2 transition relative to the ket0−ket1 transition, by more than a factor of 200. The relative modulation of the coupling rates was exploited to engineer a metastable state in the giant transmon and demonstrate electromagnetically-induced transparency (EIT), a typical signature of a lambda system. Our results show that we can transform the ladder structure of an ordinary transmon into a more interesting lambda system using a giant transmon, thereby paving the way for exploring new possibilities to study three-level physics in a waveguide-QED setting. \n \nExtending giant atom physics to multiple giant atoms, we then explore a device with two giant artificial atoms connected in a braided configuration to a transmission line. The braided topology of the qubits, offers an interesting regime where the qubits can interact with each other in a decoherence-free environment, where the interaction is mediated by virtual photons in the transmission line. We probe the resonant behavior of the qubits at two different frequency bias points, where we observe qualitatively different scattering behavior. Furthermore, when probing for the Autler-Townes Splitting (ATS), multiple resonances are observed for both resonant and off-resonant cases instead of the familiar doublet in the ATS spectroscopy. This comes as a surprise as the frequency-level spacings in both qubits are nominally identical. We believe these features could be an indication of a novel resonant interaction between the qubits facilitated by the braided topology. An effort to understand this theoretically is underway. \n \nFor our second study, we explore a system with two parametrically-coupled superconducting resonators, which implements an optomechanical-like interaction in an all-electrical network. The nonlinear nature of this interaction is mediated by a superconducting quantum interference device (SQUID), where the current in one resonator couples to the photon number in the other resonator. We propose to use this system to build a ``photonic piston" engine in the quantum regime. We motivate the feasibility of the proposal by reviewing key theoretical results which demonstrate an Otto-cycle by appropriately driving the system with noise. Our experimental findings demonstrate the crucial nonlinear coupling that is required for the engine to work. We also show that we can increase the coupling strength between the resonators depending on the chosen flux operating point.