Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

One-dimensional Bose gases on an atom chip

Jorge Ferreras

Published Oct 15, 2018• 0 citations
OpenAlex

Abstract

Ultracold atomic gases have proven to be an excellent tool for research in quantum systems. A Bose gas can be trapped on an atom chip using very well defined and tunable spatially-dependent potentials. The proximity of the atoms to the chip permits the use of low currents allowing for highly accurate temporal changes. Excellent experimental apparatus is needed to achieve Bose-Einstein condensation with a sufficient atom number to study low-dimensional physics. The setup described in this document utilises a set of current-carrying structures on top of which an atom chip sits. For improved atom loading rate, a two-dimensional loading stage was added, extending the lifetime of the magnetic trap. From this loading stage to the atom chip, Bose-Einstein condensation of 105 Rubidium-87 atoms was achieved in less than 30 s, allowing for a large rate of experimental cycles. The high spatial and temporal tunability of this setup results in the ability to split the atomic cloud and quench the trapping potential geometry. Maximising the ratio between trapping frequencies for different spatial directions leads to the system presenting features of a one-dimensional gas. Manipulating the coherence dynamics of a one-dimensional Bose-Einstein condensate creates fluctuations in the phase properties of the wavefunction. These fluctuations are observed as atom density perturbations after releasing the trapping potentials, and are a tool for temperature measurements. When the cloud of atoms is positioned at a few tens of micrometres from the surface of the atom chip, corrugations in the microstructures of the chip affect the trapping potentials at very low temperatures 1 µK. This effect is simulated and quantified in the thesis, with the aim of improving future setups. Additionally, the effect is explored for microscopy purposes. The behaviour of a Bose-Einstein condensate, especially the expansion rate, has long been studied. In this thesis, the Gross-Pitaevskii Equation is introduced, finding its numerical solutions to the two-dimensional and three-dimensional forms, using the Split-Step Fourier Method. The results show very good agreement with the experimental results, as well as with other well- established theories of condensates. The creation of such a toolbox opens up the opportunity to further investigate the coherence dynamics of low-dimensional systems.

Related papers

An apparatus for the production of Bose-Einstein condensates in tunable geometries on a chip

Thomas J. Barrett

Atom chips are an excellent tool for studying ultracold degenerate quantum gases, due to the high degree of controllability afforded by the precise potentials generated from the current-carrying microfabricated wires on the chip surface. The geometries of the trapping potentials are inherently capable of realising extreme aspect ratios, and therefore creating model systems with effectively reduced dimensionality, particularly the theoretically-tractable one-dimensional Bose gas. In addition, the temporal tunability makes it possible to impart non-adiabatic changes on the trapping potentials, allowing experimental investigation of samples which have been brought out of equilibrium - a situation which is not fully theoretically understood. This thesis describes the implementation, development and characterisation of an experimental system for producing the first Bose-Einstein condensates of atomic rubidium 87 gas trapped on the surface of an atom chip in Nottingham. Such an apparatus is very complex and requires careful characterisation in order to run in a stable and reliable way. Details of the experimental setup are thoroughly outlined, including the vacuum system, lasers, electronics, computer control and timing, and the optical imaging system. A newly installed compact two-dimensional magneto-optical trap provides an loading rate of 5e7 atoms per second for loading a three-dimensional mirror-magneto-optical trap with 1.5e8 atoms, at a temperature of 300uK within 10s. The cloud is then sub-Doppler cooled to 50uK, and spin-polarised with 96% purity into the |F=2,mF=+2> ground state within 5ms, in preparation for loading a purely magnetic trap. A millimeter sized copper Z-shaped conductor located beneath the atom chip surface creates a Ioffe-Pritchard magnetic trap, into which the laser cooled cloud is loaded with 70% efficiency, and can be held with a vacuum-limited lifetime of 40s. Evaporative cooling then pre-cools the sample to below 20uK within 10s, to allow the subsequent loading into potentials created by the atom chip with 100% efficiency. A final evaporation stage then cools the cloud below the phase transition temperature of 800nK, resulting finally in pure BECs with $10^5$ atoms confined using the atom chip. Key measurements of various properties of the trapped condensates are presented, which are important in order to characterise the system fully, and to compare with theoretical expectations. In particular, included are the variation of condensate fraction with temperature, the BEC expansion dynamics, and the condensate lifetime in the trap, for example. Finally, it is demonstrated how BECs can be produced on the atom chip without the use of external macroscopic coils, achieved by using novel, integrated sheet structures located beneath the chip surface - unique to this experimental system - to create the necessary bias fields.

•Jul 12, 2017•0 citations

Dynamic manipulations of interacting 1d Bose gases

Gal Aviv

Atom chips are a great tool for creation of low dimensional magnetic trapping geometries via micro-structures on the chip surface. Such structures allow the creation of time-dependent magnetic and electric potentials with highly accurate spatial and temporal dependency. As part of this thesis we have investigated the coherence dynamics in one-dimensional Bose-Einstein condensate while creating a sudden change in the atomic trapping potential. Such sudden changes create phase perturbations of the wave function, which leads to density perturbations. Analyzing these changes enables studies of the evolution of the coherence in a one-dimensional Bose gas with dynamically changing boundary conditions. Of particular interest is the study of prethermalization which can be understood in an integrable systems as so-called generalized Gibbs state. This state does not decay, but in case that there are perturbations that break integrability, this state relaxes further to a thermal state. To get a good understanding of such 1D systems we first investigated the transition from 3D to 1D Bose gas by observing both in situ and time of flight density profiles and analyzing the spatial variations in atom number as a function of temperature, geometry, and atomic density. High quality imaging is essential in these types of atomic physics experiments, and therefore a whole chapter is devoted to a new optimization method of absorption imaging. In this method we have taken into account the quantum nature of both the atomic medium and imaging light. Last, we have outlined an experiment that utilizes one-dimensional Bose-Einstein condensate as an analogue model of quantum field theory, in particular the dynamical Casimir effect and Hawking radiation. We do so by dynamically splitting a condensate along its long axis to a Y-like shape and measure the differential phase between the branches.

•Jul 10, 2014•0 citations

Coherent manipulation of Bose-Einstein condensates with radio-frequency adiabatic potentials on atom chips

Sebastian Hofferberth

During this thesis a novel trapping and manipulation technique for neutral atoms on atom chips has been developed and experimentally implemented. Radio-frequency (rf) coupling of internal states of magnetically trapped atoms results in versatile microscopic potentials, which overcome various limitations of static magnetic traps. An extensive experimental analysis of this new technique has been carried out, exploring the state-dependency of the rf potentials and the possible realization of non-trivial trapping geometries. Based on these results, the first coherent matter wave beam splitter on an atom chip has been realized, demonstrating for the first time the all-magnetic coherent splitting of a condensate. This new atom optical tool has then been applied to investigate the phase-properties of one-dimensional Bose-Einstein condensates. The potential configuration developed during this thesis provides direct access to the phase fluctuations in the system and has allowed the first time-resolved study of equilibrium properties and non-equilibrium dynamics in a one-dimensional Bose gas.

•Jan 1, 2007•4 citations

Investigating the dynamics of a Bose Einstein condensate on an atom chip

I J M Barr

In this thesis I discuss work that has been carried out on the dynamics of a Bose Einstein condensate of Rb 87 produced near an atom chip. A Bose Einstein Condensate (BEC) is a quantum state of matter where a single quantum state becomes occupied by a macroscopic number of identical Bosons. In our case this is achieved by cooling a system of trapped identical rubidium 87 atoms to its ground state. To reach temperatures of condensation we initially laser cool atoms from room temperature, before loading them into a magnetic trap. The magnetic trap is produced through a combination of uniform magnetic fields from coils outside our vacuum chamber and currents running through wires on an atom chip. The atom chip is a microfabricated device, produced by a coating a silicon chip with a thin layer of gold and etching wires into it. Together, these fields create a magnetic field minimum 120μm from the surface of the chip which can be used to confine low field seeking hyperfine states of the atom in an elongated harmonic trap. Once the atoms are confined in the magnetic trap we used force evaporative cooling out to reach the phase space densities required for Bose Einstein condensation. The BEC is used to investigate the relative dynamics between the fraction of the atoms in the condensate to those not in the condensate. Our atom chip provided a suitable environment to investigate this due to fragmentation of the magnetic potential close to the chip. Small imperfections in the wires on our atom chip mean that the trapping potential isn’t smooth. Small regions of higher trapping frequency - or fragments - are formed. Due to the small size of these fragments it is possible to find a position where a condensate can form in the fragment, and see a potential of high frequency, whereas a non-condensed atom will see a lower frequency potential. We exploit this to set the condensed fraction moving relative to the non condensed part and investigate the subsequent damping of their motion relative to each other.

•May 1, 2015•2 citations

Bose-Einstein condensates on a magnetic film atom chip

S. Whitlock

Atom chips are devices used to magnetically trap and manipulate ultracold atoms and Bose-Einstein condensates near a surface. In particular, permanent magnetic film atom chips can allow very tight confinement and intricate magnetic field designs while circumventing technical current noise. Research described in this thesis is focused on the development of a magnetic film atom chip, the production of Bose-Einstein condensates near the film surface, the characterisation of the associated magnetic potentials using rf spectroscopy of ultracold atoms and the realisation of a precision sensor based on splitting Bose-Einstein condensates in a double-well potential. The atom chip itself combines the edge of a perpendicularly magnetised GdTbFeCo film with a machined silver wire structure. A mirror magneto-optical trap collects up to 5 x 108 87Rb atoms beneath the chip surface. The current-carrying wires are then used to transfer the cloud of atoms to the magnetic film microtrap and radio frequency evaporative cooling is applied to produce Bose-Einstein condensates consisting of 1 x 105 atoms. We have identified small spatial magnetic field variations near the film surface that fragment the ultracold atom cloud. These variations originate from inhomogeneity in the film magnetisation and are characterised using a novel technique based on spatially resolved radio frequency spectroscopy of the atoms to map the magnetic field landscape over a large area. The observations agree with an analytic model for the spatial decay of random magnetic fields from the film surface. Bose-Einstein condensates in our unique potential landscape have been used as a precision sensor for potential gradients. We transfer the atoms to the central region of the chip which produces a double-well potential. A single BEC is formed far from the surface and is then dynamically split in two by moving the trap closer to the surface. After splitting, the population of atoms in each well is extremely sensitive to the asymmetry of the potential and can be used to sense tiny magnetic field gradients or changes in gravity on a small spatial scale.

•Jan 1, 2007•5 citations

A cold atom apparatus for the microscopy of thin membranes

Amruta Gadge

Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.

•Jul 19, 2018•0 citations
Ultracold atomic gases have proven to be an excellent tool for research in quantum systems. A Bose gas can be trapped on an atom chip using very well defined and tunable spatially-dependent potentials. The proximity of the atoms to the chip permits the use of low currents allowing for highly accurate temporal changes. Excellent experimental apparatus is needed to achieve Bose-Einstein condensation with a sufficient atom number to study low-dimensional physics. The setup described in this document utilises a set of current-carrying structures on top of which an atom chip sits. For improved atom loading rate, a two-dimensional loading stage was added, extending the lifetime of the magnetic trap. From this loading stage to the atom chip, Bose-Einstein condensation of 105 Rubidium-87 atoms was achieved in less than 30 s, allowing for a large rate of experimental cycles. The high spatial and temporal tunability of this setup results in the ability to split the atomic cloud and quench the trapping potential geometry. Maximising the ratio between trapping frequencies for different spatial directions leads to the system presenting features of a one-dimensional gas. Manipulating the coherence dynamics of a one-dimensional Bose-Einstein condensate creates fluctuations in the phase properties of the wavefunction. These fluctuations are observed as atom density perturbations after releasing the trapping potentials, and are a tool for temperature measurements. When the cloud of atoms is positioned at a few tens of micrometres from the surface of the atom chip, corrugations in the microstructures of the chip affect the trapping potentials at very low temperatures 1 µK. This effect is simulated and quantified in the thesis, with the aim of improving future setups. Additionally, the effect is explored for microscopy purposes. The behaviour of a Bose-Einstein condensate, especially the expansion rate, has long been studied. In this thesis, the Gross-Pitaevskii Equation is introduced, finding its numerical solutions to the two-dimensional and three-dimensional forms, using the Split-Step Fourier Method. The results show very good agreement with the experimental results, as well as with other well- established theories of condensates. The creation of such a toolbox opens up the opportunity to further investigate the coherence dynamics of low-dimensional systems.
Atom chips are an excellent tool for studying ultracold degenerate quantum gases, due to the high degree of controllability afforded by the precise potentials generated from the current-carrying microfabricated wires on the chip surface. The geometries of the trapping potentials are inherently capable of realising extreme aspect ratios, and therefore creating model systems with effectively reduced dimensionality, particularly the theoretically-tractable one-dimensional Bose gas. In addition, the temporal tunability makes it possible to impart non-adiabatic changes on the trapping potentials, allowing experimental investigation of samples which have been brought out of equilibrium - a situation which is not fully theoretically understood. This thesis describes the implementation, development and characterisation of an experimental system for producing the first Bose-Einstein condensates of atomic rubidium 87 gas trapped on the surface of an atom chip in Nottingham. Such an apparatus is very complex and requires careful characterisation in order to run in a stable and reliable way. Details of the experimental setup are thoroughly outlined, including the vacuum system, lasers, electronics, computer control and timing, and the optical imaging system. A newly installed compact two-dimensional magneto-optical trap provides an loading rate of 5e7 atoms per second for loading a three-dimensional mirror-magneto-optical trap with 1.5e8 atoms, at a temperature of 300uK within 10s. The cloud is then sub-Doppler cooled to 50uK, and spin-polarised with 96% purity into the |F=2,mF=+2> ground state within 5ms, in preparation for loading a purely magnetic trap. A millimeter sized copper Z-shaped conductor located beneath the atom chip surface creates a Ioffe-Pritchard magnetic trap, into which the laser cooled cloud is loaded with 70% efficiency, and can be held with a vacuum-limited lifetime of 40s. Evaporative cooling then pre-cools the sample to below 20uK within 10s, to allow the subsequent loading into potentials created by the atom chip with 100% efficiency. A final evaporation stage then cools the cloud below the phase transition temperature of 800nK, resulting finally in pure BECs with 10510^5105 atoms confined using the atom chip. Key measurements of various properties of the trapped condensates are presented, which are important in order to characterise the system fully, and to compare with theoretical expectations. In particular, included are the variation of condensate fraction with temperature, the BEC expansion dynamics, and the condensate lifetime in the trap, for example. Finally, it is demonstrated how BECs can be produced on the atom chip without the use of external macroscopic coils, achieved by using novel, integrated sheet structures located beneath the chip surface - unique to this experimental system - to create the necessary bias fields.
Atom chips are a great tool for creation of low dimensional magnetic trapping geometries via micro-structures on the chip surface. Such structures allow the creation of time-dependent magnetic and electric potentials with highly accurate spatial and temporal dependency. As part of this thesis we have investigated the coherence dynamics in one-dimensional Bose-Einstein condensate while creating a sudden change in the atomic trapping potential. Such sudden changes create phase perturbations of the wave function, which leads to density perturbations. Analyzing these changes enables studies of the evolution of the coherence in a one-dimensional Bose gas with dynamically changing boundary conditions. Of particular interest is the study of prethermalization which can be understood in an integrable systems as so-called generalized Gibbs state. This state does not decay, but in case that there are perturbations that break integrability, this state relaxes further to a thermal state. To get a good understanding of such 1D systems we first investigated the transition from 3D to 1D Bose gas by observing both in situ and time of flight density profiles and analyzing the spatial variations in atom number as a function of temperature, geometry, and atomic density. High quality imaging is essential in these types of atomic physics experiments, and therefore a whole chapter is devoted to a new optimization method of absorption imaging. In this method we have taken into account the quantum nature of both the atomic medium and imaging light. Last, we have outlined an experiment that utilizes one-dimensional Bose-Einstein condensate as an analogue model of quantum field theory, in particular the dynamical Casimir effect and Hawking radiation. We do so by dynamically splitting a condensate along its long axis to a Y-like shape and measure the differential phase between the branches.
During this thesis a novel trapping and manipulation technique for neutral atoms on atom chips has been developed and experimentally implemented. Radio-frequency (rf) coupling of internal states of magnetically trapped atoms results in versatile microscopic potentials, which overcome various limitations of static magnetic traps. An extensive experimental analysis of this new technique has been carried out, exploring the state-dependency of the rf potentials and the possible realization of non-trivial trapping geometries. Based on these results, the first coherent matter wave beam splitter on an atom chip has been realized, demonstrating for the first time the all-magnetic coherent splitting of a condensate. This new atom optical tool has then been applied to investigate the phase-properties of one-dimensional Bose-Einstein condensates. The potential configuration developed during this thesis provides direct access to the phase fluctuations in the system and has allowed the first time-resolved study of equilibrium properties and non-equilibrium dynamics in a one-dimensional Bose gas.
In this thesis I discuss work that has been carried out on the dynamics of a Bose Einstein condensate of Rb 87 produced near an atom chip. A Bose Einstein Condensate (BEC) is a quantum state of matter where a single quantum state becomes occupied by a macroscopic number of identical Bosons. In our case this is achieved by cooling a system of trapped identical rubidium 87 atoms to its ground state. To reach temperatures of condensation we initially laser cool atoms from room temperature, before loading them into a magnetic trap. The magnetic trap is produced through a combination of uniform magnetic fields from coils outside our vacuum chamber and currents running through wires on an atom chip. The atom chip is a microfabricated device, produced by a coating a silicon chip with a thin layer of gold and etching wires into it. Together, these fields create a magnetic field minimum 120μm from the surface of the chip which can be used to confine low field seeking hyperfine states of the atom in an elongated harmonic trap. Once the atoms are confined in the magnetic trap we used force evaporative cooling out to reach the phase space densities required for Bose Einstein condensation. The BEC is used to investigate the relative dynamics between the fraction of the atoms in the condensate to those not in the condensate. Our atom chip provided a suitable environment to investigate this due to fragmentation of the magnetic potential close to the chip. Small imperfections in the wires on our atom chip mean that the trapping potential isn’t smooth. Small regions of higher trapping frequency - or fragments - are formed. Due to the small size of these fragments it is possible to find a position where a condensate can form in the fragment, and see a potential of high frequency, whereas a non-condensed atom will see a lower frequency potential. We exploit this to set the condensed fraction moving relative to the non condensed part and investigate the subsequent damping of their motion relative to each other.
Atom chips are devices used to magnetically trap and manipulate ultracold atoms and Bose-Einstein condensates near a surface. In particular, permanent magnetic film atom chips can allow very tight confinement and intricate magnetic field designs while circumventing technical current noise. Research described in this thesis is focused on the development of a magnetic film atom chip, the production of Bose-Einstein condensates near the film surface, the characterisation of the associated magnetic potentials using rf spectroscopy of ultracold atoms and the realisation of a precision sensor based on splitting Bose-Einstein condensates in a double-well potential. The atom chip itself combines the edge of a perpendicularly magnetised GdTbFeCo film with a machined silver wire structure. A mirror magneto-optical trap collects up to 5 x 108 87Rb atoms beneath the chip surface. The current-carrying wires are then used to transfer the cloud of atoms to the magnetic film microtrap and radio frequency evaporative cooling is applied to produce Bose-Einstein condensates consisting of 1 x 105 atoms. We have identified small spatial magnetic field variations near the film surface that fragment the ultracold atom cloud. These variations originate from inhomogeneity in the film magnetisation and are characterised using a novel technique based on spatially resolved radio frequency spectroscopy of the atoms to map the magnetic field landscape over a large area. The observations agree with an analytic model for the spatial decay of random magnetic fields from the film surface. Bose-Einstein condensates in our unique potential landscape have been used as a precision sensor for potential gradients. We transfer the atoms to the central region of the chip which produces a double-well potential. A single BEC is formed far from the surface and is then dynamically split in two by moving the trap closer to the surface. After splitting, the population of atoms in each well is extremely sensitive to the asymmetry of the potential and can be used to sense tiny magnetic field gradients or changes in gravity on a small spatial scale.
Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.