In this work we study radiation-matter interaction in the limit of a single excitation when nano-mechanical effects act on the single photon emitted by a qubit. In particular, we use two different models. In the first model, we consider an opto-mechanical cavity with an oscillating mirror in front of a qubit, initially in its excited state. A photon is emitted and reflected by the mirror so it can re-excite the qubit and so continue a process of controlled emission. The qubit interacts with a continuous bath of harmonic oscillators with which energy can be partially exchanged. Results show that the time-dependent dynamics of light emission can be Markovian or non-Markovian. In both cases, the frequency spectrum exhibits sideband photons associated with nano-mechanical oscillations. In the second model, in addition to the opto-mechanical cavity, the qubit is located on an optical nano-cavity. In this picture we have two couplings, while the first one acts between the qubit and the single mode of the optical nano-cavity, the second one acts between the external modes of the opto-mechanical and the single mode of optical nano-cavity. The results of the time-dependent dynamics in the qubit-nanocavity, show that this system is capable of exchanging its only coherent excitation due to feedback produced by the mirror, even if the first coupling is weak. The energy exchange with the external modes produces a type-like Rabi oscillation, in which the system behaves as if it were in the strong coupling regime. The low amplitude of these oscillations shows that energy is partially exchanged between the external modes and the optical nano-cavity. Finally, we show that if we change the state of motion of the mirror, the entire structure of external modes does also change, causing a damping in the Rabi oscillations over time.
In this work we study radiation-matter interaction in the limit of a single excitation when nano-mechanical effects act on the single photon emitted by a qubit. In particular, we use two different models. In the first model, we consider an opto-mechanical cavity with an oscillating mirror in front of a qubit, initially in its excited state. A photon is emitted and reflected by the mirror so it can re-excite the qubit and so continue a process of controlled emission. The qubit interacts with a continuous bath of harmonic oscillators with which energy can be partially exchanged. Results show that the time-dependent dynamics of light emission can be Markovian or non-Markovian. In both cases, the frequency spectrum exhibits sideband photons associated with nano-mechanical oscillations. In the second model, in addition to the opto-mechanical cavity, the qubit is located on an optical nano-cavity. In this picture we have two couplings, while the first one acts between the qubit and the single mode of the optical nano-cavity, the second one acts between the external modes of the opto-mechanical and the single mode of optical nano-cavity. The results of the time-dependent dynamics in the qubit-nanocavity, show that this system is capable of exchanging its only coherent excitation due to feedback produced by the mirror, even if the first coupling is weak. The energy exchange with the external modes produces a type-like Rabi oscillation, in which the system behaves as if it were in the strong coupling regime. The low amplitude of these oscillations shows that energy is partially exchanged between the external modes and the optical nano-cavity. Finally, we show that if we change the state of motion of the mirror, the entire structure of external modes does also change, causing a damping in the Rabi oscillations over time.
Quantum opto-mechanics is a fast moving, broad research field which aims to investigate and control the interaction of light and the quantized motion of mechanical objects and the coupling between them. This allows one to engineer the mechanical quantum state by controlling and measuring the electromagnetic field, and conversely, to control the dynamical evolution of the optical field via its interaction with a mechanical system. Mechanical resonators are accessible in many different shapes and sizes, from kilogram scales in experiments that test gravitational theories to micro- and nano-scales in resolved sideband regime, where the frequency of the mechanical resonator is larger than the bandwidth of the optical cavity. In this regime, it is possible to cool the mechanical object to the ground state which allows a high degree of control and the ability to prepare interesting non-classical states, states that could aid in investigating the quantum dynamics of macroscopic objects. The field of quantum opto-mechanics is a promising testbed for quantum control technologies, such as fundamental tests of quantum mechanics, ultra-sensitive quantum sensors for precise measurements, phonon lasing, mechanical memories with long lifetime and quantum information processing. Furthermore, experiments are progressing toward strong opto-mechanical coupling regimes with single photons. This creates a platform that can take advantage of the nonlinear optical interactions to generate highly non-classical states in such light-matter interfaces. Photonic systems working in the single photon regime will be promising for low power applications and also for implementations of quantum information and computation. Motivated by these applications, this thesis consists of theoretical studies in the context of single photonics. This includes investigating non-classical mechanical state generation and mechanically controlling the dynamical evolution of optical fields in the strong coupling regime single photon opto-mechanics and furthermore, proposing a quantum sensor using single photonics. In this regard, we employ three important formalisms to treat and measure open quantum systems with non-Gaussian input fields: the conditional and unconditional cascaded master equations, Fock-state master equations and input-output Langevin equations. In the context of opto-mechanics, the system to be investigated is composed of two optical cavities with a coupling modulated via a mechanical resonator. In one case, a sequence of single photons are irreversibly sent to one of the optical cavities. After photons go through the opto-mechanical interaction, photon counting measurements are performed on the cavity output, conditionally steering the mechanical state to a highly non-classical Fock state. Numerical calculations are performed to predict the experimental parameters needed to generate a mechanical Fock state before the mechanical object is thermalized. In another case, the same opto-mechanical scheme is employed to conversely modify the state of the optical mode by engineering the state of the mechanical degree of freedom. In this case, it is shown that the opto-mechanical system operates as an effective beam splitter for the input single photons, with a transmission that can be controlled by tuning the number of excitations in the bulk mechanical resonator. When the mechanical resonator has a small coherent amplitude it acts as a quantum control, entangling the optical and mechanical degrees of freedom. As the coherent amplitude of the resonator increases, it acts as a classical control for the input photons. Finally, we propose a novel multi-purpose sensor architecture that can be used for force, refractive index and possibly local temperature detection. In this scheme, two coupled cavities behave as an effective beam splitter. This sensor is based on fourth order interference (the Hong-Ou-Mandel effect) and requires a sequence of single photon pulses and consequently has low pulse power. Changes in the parameter to be measured induce variations in the effective beam splitter reflectivity and result in changes to the visibility of interference. We propose that this generic scheme could be implemented with coupled L3 photonic crystal cavities and find that this system, which only relies on photon coincidence detection and does not need any spectral resolution, can estimate forces as small as 10-7 Newtons and can measure one part per million change in refractive index using a very low input power of 10-10 W.
In this thesis three different approaches to control the quantum statistics in nanoscopic devices are investigated. In the first part of the thesis, mechanical oscillations in solid state devices are manipulated by an external laser to show bistabilities, coherent amplification, and enhanced damping. The dynamics is controlled by the frequency of the external laser. This study is performed in a semiclassical approximation, where expectation values of operators are factorized. These effects are used to show the similarities and differences between optomechanical systems and phonon cavities. In the regime of coherent amplification of phonons the theoretical description is extended to a fully quantum mechanical model. This reveals additional resonances due to collective processes that can be addressed via the frequency of the external laser. In the second part, a quantum light source is considered for manipulation of the emission statistics of a second quantum optical system serving as target. A Jaynes-Cummings system is used as a source that may be tuned from nonclassical to thermal emission via the pump strength. The target consists of a cavity with two emitters. The nature of the imprinted statistics is studied by higher order correlation functions. The resulting statistics deviates strongly from thermal, coherent or antibunched statistics. The third part considers coherent self feedback with time-delay, which is motivated by classical Pyragas control. The finite time delay is used as control parameter. The matrix product state evolution in the picture of the quantum stochastic Schrödinger equation is employed as a systematic way of dealing with quantum self-feedback. In this thesis, the approach is extended to include higher order terms in the time evolution operator. This is done systematically so that arbitrary order can be included enabling faster numerical evaluation. This extension of the matrix product state evolution method allows to investigate efficiently the emission statistics of a single mode cavity containing two emitters. It is shown that feedback can enhance antibunching in the light field while also counter-intuitively increasing the number of emitted photons at the same time. Expressing the time evolution operator as a sum of sparse matrices allows to include time dependent Hamiltonians in an efficient manner. Considering the pulsed excitation of a two level emitter, it is demonstrated that emission statistics may be tuned via feedback. This allows to switch between single photon emission and enhanced two photon emission.
Impressive progress has been achieved in controlling the spontaneous emission rate for emitters in Nanophotonic structures, such as microcavities, photonic crystals and nano-antennas. In all cases, however, the modification of the emission is stationary in time. Thus, the emission rate is time-independent and the distribution of photon emission times are stochastic and follow an exponential distribution in the weak coupling regime. In this paper, by using fast all-optical switching of a microcavity, the cavity resonance is tuned within tens of picosesonds. This drastically changes the local optical density of states at the emission frequency within the emission lifetime of the emitters. This paper theoretically studied an ensemble of two-level sources with a time dependent decay rate and have derived the excited state population and emitted intensity as a function of time for continuous wave and pulsed excitation. Deterministic bursts of dramatically enhanced or inhibited emission intensity within short intervals. Thereby, we control the photon distribution to show behavior that strongly deviates from single exponential decay. This can be used to protect quantum information systems against decoherence and to realize non-Markovian dynamics in cavity quantum electrodynamics.
We theoretically investigate quantum Rabi oscillations in a system consisting of a two-level atom (qubit) strongly coupled to a one-dimensional open waveguide. In contrast to conventional cavity quantum electrodynamics, the qubit interacts with a continuum of propagating modes, which gives rise to fundamentally different dynamical behavior. Within the rotating-wave approximation, we express the multimode Jaynes-Cummings Hamiltonian in terms of collective bosonic operators and show that the system possesses two integrals of motion, enabling an exact diagonalization of the Hamiltonian in the single-excitation subspace. We show that for a strongly interacting qubit-photon system, the dynamics are captured by a reduced two-level model. In this framework, each level is defined as the product of the atomic excited state and a specific field mode, which takes the form of a multiphoton Fock-like state. In this picture, the Rabi oscillations represent a collective phenomenon corresponding to oscillations between multiphoton states differing by a single photon. We then extend our analysis to multiphoton processes in which the initial field is a coherent state with a continuous spectrum. In this case, the Rabi frequency is shown to be sensitive to the spectral profile of the function that generates the coherent state.
Abstract The future of quantum information processing hinges on chip-scale nanophotonics, specifically cavity QED and waveguide QED. One of the foremost processes underpinning quantum photonic technologies is the phenomenon of Rabi oscillations, which manifests when a qubit is irradiated by an intense laser source. Departing from the conventional semiclassical framework, we explore the more general, quantum theoretical case where the optical excitation takes the form of a multiphoton Fock state, and the qubit couples to a continuum of radiation modes. By employing the real-space formalism, we analytically explore the scattering dynamics of the photonic Fock state as it interfaces with a two-level emitter. The resulting amplitude for atomic excitation features a linear superposition of various independent scattering events that are triggered by the potential of sequential, time-delayed photon absorptions and emissions. The lowest-order excitation event, initiated by the stochastic scattering of one of the several photons, appropriately characterizes the dynamics in a weak-field environment. This event is complemented by a multitude of higher-order scattering events ensuing from repeated atom–photon interactions. The temporal evolution of the qubit excitation in our configuration closely mirrors the semiclassical predictions, particularly in the strong-pumping limit where Rabi oscillations unfold. Notably, this compatibility with the semiclassical paradigm transcends beyond the strong-excitation regime and applies both to the weak-driving and large-detuning limits. In a nutshell, our analysis extends the existing results on quantum Rabi oscillations pertinent to single-mode cavity QED, to the multimode, waveguide-QED configurations wherein flying photons are the information carriers. Additionally, we delve into the dynamics of pulsed wave packets, shedding light on the potential to substantially enhance excitation efficiency, even in scenarios involving just a few photons. Beyond their theoretical merit, these findings should hold practical relevance for future Fock-state-based quantum computing and emerging waveguide-integrated photonic technologies such as those involving superconducting circuitry.
A single two-level emitter coupled to a single mode of an electromagnetic resonator constitutes the most fundamental instance of light--matter interaction. Realizations of this type of system are investigated in the field of cavity quantum electrodynamics (cavity QED). Particularly important are schemes in which the coupling is strong enough to exceed the spontaneous emission rate as well as cavity damping. In this case, the coherent exchange of excitation between source and photon is the dominating process, providing the unique possibility to deterministically control the quantum evolution of the system. Great progress has recently been accomplished, technologically as well as conceptually, and the focus section in this issue of Journal of Optics B: Quantum and Semiclassical Optics features five articles highlighting important recent developments in the field. Strong coupling between single atoms and the electromagnetic cavity field have been achieved in two distinct regimes, the optical and the microwave region. The latter is represented by the micromaser, a high-Q microwave cavity pumped by a beam of highly excited Rydberg atoms. It has proved to be an almost ideal system for the generation of non-classical field states. A constraint in these experiments is the fact that the field inside the cavity can only be examined indirectly, by analysing the occupation of atoms leaving the cavity. While only two atomic states were previously identified for this purpose, V A Reshetov shows in his article (pages 119--126) that more information on the field may be extracted by taking advantage of the Zeeman substructure of the atomic levels. In the optical domain of cavity QED, by contrast, the state of the resonator field may be probed directly by measuring the light leaking from the cavity using photodetectors. In order to minimize damping, high-quality cavities must be employed. In most optical experiments these are Fabry--Perot resonators with ultra-high reflectivity mirrors, with losses as low as a few parts per million being state of the art. At the same time, the coupling of atoms and photons is enhanced by reducing the length of the cavity, so that strong coupling conditions are reached. A very attractive application of this type of cavity QED setup is the possibility of exerting control over the quantum dynamics of the system. An impressive example is the implementation of quantum feedback, reported in the paper by W P Smith and L A Orozco (pages 127--134). Using information gained from detecting a single photon escaping from the cavity, active feedback is applied to halt the dynamical evolution of the system. This is the first time active feedback has been used to modify the quantum evolution of a system at the single-photon level. The authors discuss how detunings between the subsystems affect the quantum feedback, an issue particularly relevant for ensembles of atoms with a spread in detuning. Perfect quantum feedback in this case requires the use of additional parameters to control the system. The majority of optical cavity QED experiments performed so far have used as a medium atoms traversing the cavity on random trajectories, such as, for example, thermal atomic beams. In this case, the observation of quantum effects is degraded in two ways. The Doppler effect and the finite transit time lead to line broadening, while the spatial structure of the cavity mode results in atoms in different locations experiencing different coupling with the photonic field. J E Reiner et al (pages 135--142) investigate the impact of these effects on quantum fluctuations in their cavity QED system. In order to overcome line broadening, they have developed a continuous cold atomic beam, extracted from a magneto-optical trap. An even better control of broadening effects and fluctuating coupling strength is provided by trapping the atoms inside the cavity and cooling them to temperatures at which their position spread is smaller than the optical wavelength. Much recent activity has been devoted to developing such an ultimate cavity QED system. A Vukics et al (pages 143--153) present a theoretical proposal for dynamically trapping and cooling atoms inside a cavity. By driving the atoms with a standing wave injected from the side of the cavity and by weakly exciting the cavity field itself, they predict three-dimensional trapping of the atom for periods around 1 second, an extremely long time on the typical scale of cavity QED dynamics. The essential component of their scheme is the interference between the two driving fields, determining the temperature of the particle and the stable trapping positions. In the quest for better confinement of radiation, lately, an appealing alternative to the Fabry--Perot cavity has been investigated -- the optical microsphere resonator. A sphere with a diameter of a few tens of microns, it supports so-called whispering gallery modes near its circumference, for which quality factors up to 10 10 have been measured. In order to exploit the correspondingly low field damping rates for cavity QED, a method must be found to couple atomic or solid state emitters to these modes. S Göotzinger et al (pages 154--158) report the coupling of single nanocrystals on the surface of a microsphere through the evanescent field of the mode. Selective excitation of a single nano-emitter was accomplished with a scanning confocal microscope. The system is a promising candidate for cavity QED with single-quantum emitters. The ability to fully control the quantum dynamics of atoms and light is beginning to spawn early applications. The most notable example is quantum information processing. This requires the coherent manipulation of single-quantum systems, which is ideally provided by cavity QED interaction in the strong-coupling limit. The development of practical devices will be among the principal future tasks for research in the field. This will include physical systems, which have not been covered in this issue, such as semiconductors, quantum dots as emitters, or photonic crystals as resonator structures. Cavity QED is therefore guaranteed to remain a vigorous field in the years to come.