Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEJ Transactions on Fundamentals and Materials

Energy Reduction in Shunt-resistor-free Low-voltage Rapid Single-flux-quantum Circuits

Masamitsu Tanaka, Ryo Sato, Yuki Hatanaka, Akira Fujimaki

Published Jan 1, 2016• 2 citations
Publisher

Abstract

We report energy reduction in low-voltage rapid single-flux-quantum (LV-RSFQ) circuits using shunt-resistor-free Josephson junctions. The LV-RSFQ logic is one of energy-efficient derivatives of rapid single-flux-quantum (RSFQ) logic, which operates in a constant voltage mode. By lowering bias voltages, we can reduce power consumption at bias resistors which account for more than 90% of total power consumption, and also reduce the energy dynamically consumed during switching events because of slower transition of superconductor phase. Voltage drops across Josephson junctions cause a complicated trade-off between operation speed and power consumption. In this paper, we evaluated shunt-resistor-free LV-RSFQ shift-registers in terms of operation speed, power consumption, and energy-efficiency. Numerical simulation revealed their faster operation by up to 50% and accordingly higher energy-efficiency. Experimental results showed that a 0.5mV shift-register had superiority in operation speed and energy-efficiency.

DOI
10.1541/ieejfms.136.740

Related papers

Low-Energy Consumption RSFQ Circuits Driven by Low Voltages

Masamitsu Tanaka, A. Kitayama, T. Koketsu +2 more

We report successful operations of low-energy consumption rapid single-flux-quantum (RSFQ) circuits applying lowered driving voltages, called LV-RSFQ, using different fabrication processes. In the LV-RSFQ, we feed bias currents to Josephson junctions from lowered constant voltages (less than 1 mV) through small resistors without extra inductors. Both static and dynamic energy consumption are reduced because of suppression of amplitudes of SFQ pulses, in exchange for slower switching speed. We show that the switching speed in LV-RSFQ circuits is improved by increasing critical current density of Josephson junctions. We demonstrated high-speed operations of LV-RSFQ shift registers in a range of 5-40 GHz and 15-90 GHz using the 2.5-kA/cm2and 10-kA/cm2fabrication technologies, respectively. Comparison of the experimental results of the LV-RSFQ circuits fabricated using two different technologies derives the optimum bias voltage in terms of energy-delay product ranged from 0.1 to 1.0ICRS, whereICRSis the product of Josephson critical current and shunt resistance.

IEEE Transactions on Applied Superconductivity•Jan 15, 2013•56 citations

18-GHz, 4.0-aJ/bit Operation of Ultra-Low-Energy Rapid Single-Flux-Quantum Shift Registers

Masamitsu Tanaka, Masato Ito, Kitayama Atsushi +2 more

We demonstrate rapid single-flux-quantum (RSFQ) circuits with reduced energy consumption by lowering the driving voltages and critical currents of Josephson junctions (JJs). At lowered voltages, the energy statically consumed by bias resistors (which is dominant in RSFQ circuits) is reduced. In addition, we show that when RSFQ circuits are driven by lowered constant voltages, the dynamic energy consumption resulting from the switching of JJs is reduced because of the suppression of the amplitudes of the signal voltage pulses, even though the switching speed becomes slower. Utilization of miniaturized JJs with smaller critical currents also leads to the reduction of static and dynamic energy consumption without decreasing the switching speed. We have designed and tested ultra-low-energy 8-bit shift registers, and verified the correctness of high-speed operations up to 18 GHz. The average energy consumption, including that at the bias resistors, was measured at 4.0 aJ/bit, which represents an energy efficiency two orders of magnitude better than that of standard RSFQ circuits.

Japanese Journal of Applied Physics•May 1, 2012•159 citations

消費電力数nWの単一磁束量子回路の動作実証

Atsushi KITAYAMA, MASATO ITO, 智仁 纐纈 +4 more

We have demonstrated rapid-single-flux-quantum (RSFQ) circuits with reduced power consumptions by lowering bias voltages and critical currents. The power consumption including a power consumption of a bias resistor is measured to be around 1 nW/JJ in 8-bit shift registers, while the operating frequency ranges from 7.5 GHz to 20 GHz. we lower bias voltages applied to RSFQ circuits. The values of bias resistances are proportional to bias voltages. At lowered bias voltages, the power consumption of the bias resistor is reduced. When a voltage begins to be generated at a Josephson junction, the net current provided to the junction and to the shunt resistor is decreased. As a result, the magnitude of the voltage is suppressed, and the power consumption of the shunt resistor is reduced. The power energy-delay product is about 70 times smaller and the the energy-delay product is more than 13 times smaller than that of the conventional RSFQ circuits. Low poewer SFQ circuits are superior in terms of energy-delay product to semiconductor circuits though the power consumption of SFQ cicuits contains the refrigerating machine.

•Jul 1, 2011•0 citations

Simulation Analysis and Energy-Saving Techniques for ERSFQ Circuits

Naveen Kumar Katam, Oleg A. Mukhanov, Massoud Pedram

Energy-efficient rapid single flux quantum (ERSFQ) circuits have become a viable alternative for the implementation of superconducting circuits due to a large amount of static power consumption in RSFQ circuits. ERSFQ circuits are built upon the popular RSFQ logic circuits by replacing the power-dissipating resistor bias network with a bias network consisting of active devices. In this paper, a simulation study of ERSFQ biasing scheme is carried out by building simulation test benches for both synchronous and asynchronous ERSFQ circuits. A study is carried out to present the optimum value of biasing inductance, influence of the feeding Josephson transmission line (FJTL) and the effect of its size, the effect of the feeding clock frequency, and the effect of the circuit operating frequency. An innovative clock-choking mechanism using magnetic Josephson junctions is also proposed for the FJTL in the case of no logic circuit activity for a current-recycling circuit block, which would help in eliminating the dynamic power consumed due to the switching of bias junctions in a logic circuit. Simulation results for current recycling ERSFQ circuits are presented along with a strategy for implementing large superconducting circuits.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•23 citations

Low-power high-speed half-flux-quantum circuits driven by low bias voltages

Feng Li, Yuto Takeshita, Daiki Hasegawa +3 more

Abstract Half-flux-quantum (HFQ) circuits store and propagate half-flux quanta. The basic circuit element is a 0-π SQUID, which is a superconducting quantum interference device with a conventional Josephson junction (0-junction) and a π-shifted ferromagnetic junction (π-junction). A 0-π SQUID achieves a small critical current in the absence of an external magnetic field, thus reducing power consumption. It is easy to set up 0-0-π SQUIDs with two 0-junctions and a π-junction which serves as a π phase-shifter. We simulated 0-0-π SQUID-based HFQ circuits driven by low bias voltages, referred to as LV-HFQ circuits. In these circuits, shunt resistors are not required for switching junctions because there is no hysteresis in the current–voltage characteristics of 0-0-π SQUIDs. We estimated the power consumption and maximum operating frequency of an HFQ Josephson transmission line based on 0-0-π SQUIDs. When operating at 43.5 GHz, the power dissipation of a single element composed of a 0-0-π SQUID and a bias resistor fell to about 0.165 nW when biased at 60 μV. The LV-HFQ circuit is potentially more power-efficient than all other currently available superconducting logic circuits.

Superconductor Science and Technology•Nov 16, 2020•34 citations

Research on the Bias Network of Energy-Efficient Single Flux Quantum Circuits

Guanqun Li, Jie Ren, Yu Wu +4 more

Superconducting single flux quantum (SFQ) circuits have been shown to offer huge advantages that are ideal for high performance computing applications. These circuits can operate at very high frequencies (tens of GHz) but consume very low power (from nanowatts to microwatts per gate). Energy-efficient SFQ (ERSFQ) circuits, evolved from traditional rapid SFQ (RSFQ) circuits, were invented with the goal of elimination of static power dissipation. When compared with RSFQ circuits, ERSFQ circuits require a new biasing network that includes biasing Josephson junction(s), biasing inductor(s), and feeding Josephson transmission line(s). Some general suggestions on how to design the network have been offered, but a detailed analysis and optimization scenario for the network is still to be provided. In this paper, we first optimize the previously reported DC-biased two-Josephson junction per bit RSFQ shift register circuit, which can be used to provide a more robust, energy-efficient, and high memory capacity storage unit. The simulated power dissipation of 16-bit RSFQ shift register is 0.45 μW per bit when operating at 21.7 GHz. We then convert the RSFQ-based shift register into an ERSFQ structure and investigate the effects of the ERSFQ bias network on the margins of the ERSFQ circuit. Finally, we propose a more comprehensive optimization method for the ERSFQ biasing network.

IEEE Transactions on Applied Superconductivity•May 2, 2019•11 citations
We report energy reduction in low-voltage rapid single-flux-quantum (LV-RSFQ) circuits using shunt-resistor-free Josephson junctions. The LV-RSFQ logic is one of energy-efficient derivatives of rapid single-flux-quantum (RSFQ) logic, which operates in a constant voltage mode. By lowering bias voltages, we can reduce power consumption at bias resistors which account for more than 90% of total power consumption, and also reduce the energy dynamically consumed during switching events because of slower transition of superconductor phase. Voltage drops across Josephson junctions cause a complicated trade-off between operation speed and power consumption. In this paper, we evaluated shunt-resistor-free LV-RSFQ shift-registers in terms of operation speed, power consumption, and energy-efficiency. Numerical simulation revealed their faster operation by up to 50% and accordingly higher energy-efficiency. Experimental results showed that a 0.5mV shift-register had superiority in operation speed and energy-efficiency.
We report successful operations of low-energy consumption rapid single-flux-quantum (RSFQ) circuits applying lowered driving voltages, called LV-RSFQ, using different fabrication processes. In the LV-RSFQ, we feed bias currents to Josephson junctions from lowered constant voltages (less than 1 mV) through small resistors without extra inductors. Both static and dynamic energy consumption are reduced because of suppression of amplitudes of SFQ pulses, in exchange for slower switching speed. We show that the switching speed in LV-RSFQ circuits is improved by increasing critical current density of Josephson junctions. We demonstrated high-speed operations of LV-RSFQ shift registers in a range of 5-40 GHz and 15-90 GHz using the 2.5-kA/cm2and 10-kA/cm2fabrication technologies, respectively. Comparison of the experimental results of the LV-RSFQ circuits fabricated using two different technologies derives the optimum bias voltage in terms of energy-delay product ranged from 0.1 to 1.0ICRS, whereICRSis the product of Josephson critical current and shunt resistance.
We demonstrate rapid single-flux-quantum (RSFQ) circuits with reduced energy consumption by lowering the driving voltages and critical currents of Josephson junctions (JJs). At lowered voltages, the energy statically consumed by bias resistors (which is dominant in RSFQ circuits) is reduced. In addition, we show that when RSFQ circuits are driven by lowered constant voltages, the dynamic energy consumption resulting from the switching of JJs is reduced because of the suppression of the amplitudes of the signal voltage pulses, even though the switching speed becomes slower. Utilization of miniaturized JJs with smaller critical currents also leads to the reduction of static and dynamic energy consumption without decreasing the switching speed. We have designed and tested ultra-low-energy 8-bit shift registers, and verified the correctness of high-speed operations up to 18 GHz. The average energy consumption, including that at the bias resistors, was measured at 4.0 aJ/bit, which represents an energy efficiency two orders of magnitude better than that of standard RSFQ circuits.
We have demonstrated rapid-single-flux-quantum (RSFQ) circuits with reduced power consumptions by lowering bias voltages and critical currents. The power consumption including a power consumption of a bias resistor is measured to be around 1 nW/JJ in 8-bit shift registers, while the operating frequency ranges from 7.5 GHz to 20 GHz. we lower bias voltages applied to RSFQ circuits. The values of bias resistances are proportional to bias voltages. At lowered bias voltages, the power consumption of the bias resistor is reduced. When a voltage begins to be generated at a Josephson junction, the net current provided to the junction and to the shunt resistor is decreased. As a result, the magnitude of the voltage is suppressed, and the power consumption of the shunt resistor is reduced. The power energy-delay product is about 70 times smaller and the the energy-delay product is more than 13 times smaller than that of the conventional RSFQ circuits. Low poewer SFQ circuits are superior in terms of energy-delay product to semiconductor circuits though the power consumption of SFQ cicuits contains the refrigerating machine.
Energy-efficient rapid single flux quantum (ERSFQ) circuits have become a viable alternative for the implementation of superconducting circuits due to a large amount of static power consumption in RSFQ circuits. ERSFQ circuits are built upon the popular RSFQ logic circuits by replacing the power-dissipating resistor bias network with a bias network consisting of active devices. In this paper, a simulation study of ERSFQ biasing scheme is carried out by building simulation test benches for both synchronous and asynchronous ERSFQ circuits. A study is carried out to present the optimum value of biasing inductance, influence of the feeding Josephson transmission line (FJTL) and the effect of its size, the effect of the feeding clock frequency, and the effect of the circuit operating frequency. An innovative clock-choking mechanism using magnetic Josephson junctions is also proposed for the FJTL in the case of no logic circuit activity for a current-recycling circuit block, which would help in eliminating the dynamic power consumed due to the switching of bias junctions in a logic circuit. Simulation results for current recycling ERSFQ circuits are presented along with a strategy for implementing large superconducting circuits.
Abstract Half-flux-quantum (HFQ) circuits store and propagate half-flux quanta. The basic circuit element is a 0-π SQUID, which is a superconducting quantum interference device with a conventional Josephson junction (0-junction) and a π-shifted ferromagnetic junction (π-junction). A 0-π SQUID achieves a small critical current in the absence of an external magnetic field, thus reducing power consumption. It is easy to set up 0-0-π SQUIDs with two 0-junctions and a π-junction which serves as a π phase-shifter. We simulated 0-0-π SQUID-based HFQ circuits driven by low bias voltages, referred to as LV-HFQ circuits. In these circuits, shunt resistors are not required for switching junctions because there is no hysteresis in the current–voltage characteristics of 0-0-π SQUIDs. We estimated the power consumption and maximum operating frequency of an HFQ Josephson transmission line based on 0-0-π SQUIDs. When operating at 43.5 GHz, the power dissipation of a single element composed of a 0-0-π SQUID and a bias resistor fell to about 0.165 nW when biased at 60 μV. The LV-HFQ circuit is potentially more power-efficient than all other currently available superconducting logic circuits.
Superconducting single flux quantum (SFQ) circuits have been shown to offer huge advantages that are ideal for high performance computing applications. These circuits can operate at very high frequencies (tens of GHz) but consume very low power (from nanowatts to microwatts per gate). Energy-efficient SFQ (ERSFQ) circuits, evolved from traditional rapid SFQ (RSFQ) circuits, were invented with the goal of elimination of static power dissipation. When compared with RSFQ circuits, ERSFQ circuits require a new biasing network that includes biasing Josephson junction(s), biasing inductor(s), and feeding Josephson transmission line(s). Some general suggestions on how to design the network have been offered, but a detailed analysis and optimization scenario for the network is still to be provided. In this paper, we first optimize the previously reported DC-biased two-Josephson junction per bit RSFQ shift register circuit, which can be used to provide a more robust, energy-efficient, and high memory capacity storage unit. The simulated power dissipation of 16-bit RSFQ shift register is 0.45 μW per bit when operating at 21.7 GHz. We then convert the RSFQ-based shift register into an ERSFQ structure and investigate the effects of the ERSFQ bias network on the margins of the ERSFQ circuit. Finally, we propose a more comprehensive optimization method for the ERSFQ biasing network.