Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Quantum Electronics

Formation of a beam of cold atoms by laser frequency tuning

Yu. Rozhdestvensky, Anton K. Vershovskii, E A Ageichik, V. S. Zholnerov

Published Oct 11, 2016• 0 citations
Publisher

Abstract

We report the possibility of producing a beam of slow atoms with a characteristic velocity of ∼ 1 m s − 1 by the ‘chirp’ method, namely, cooling by variable-frequency radiation. Method modifications are considered, which substantially reduce dimensions of the slower, the width of the longitudinal velocity distribution of the atomic beam, and the area of its cross section. The modified method of laser radiation frequency tuning for cooling rubidium atoms is mathematically simulated.

DOI
10.1070/qel16167

Related papers

Laser cooling and trapping of rubidium

Christopher D. Wallace, Timothy T. Grove, T. Dinneen +2 more

We have laser cooled an atomic beam of rubidium with diode lasers and have used these slow atoms to load a magneto-optical trap. The cooling is performed with the frequency-chirp method,1,2 in which the laser's frequency is ramped linearly (by the injection currant) to maintain resonance with the decelerating atoms. Two synchronously chirped lasers are required to prevent optical hyperfine pumping of the ground state. The chirp typically covers 500 MHz in 10 ms. At the end of each ramp, the resulting velocity distribution is measured with a pulsed probe laser. By varying the end point of the chirp, we are able to obtain slow atoms with average velocities ranging from 200 to −50 m/s. The widths of the velocity distributions are measured to be approximately 40 m/s. This relatively large width results from the inherent linewidth (~30 MHz) of the free-running diode lasers used for both cooling and probing.

Quantum Electronics and Laser Science Conference•May 12, 1991•0 citations

Rubidium atomic funnel

T. B. Swanson, Nuno J. O. Silva, Shannon K. Mayer +2 more

A low-velocity beam of rubidium atoms is produced from a two-dimensional magneto-optic trap or atomic funnel. Atoms from a thermal beam are slowed by chirped laser cooling and then loaded into the funnel. The cold atoms are ejected by moving molasses formed with frequency-shifted laser beams. The resultant atomic beam has a controllable velocity in the range of 3 to 10 m/s, a temperature of 500 µK, and a flux of 1010 atoms/s.

Journal of the Optical Society of America B•Sep 1, 1996•29 citations

Laser cooling of a cesium beam utilizing Stark effect frequency compensation

Jeng-Rong Yeh, Barbara M. Hoeling, R. J. Knize

Laser cooling of neutral atoms has possible applications such as better frequency standards and high precision spectroscopy. It would be desirable to produce a cold continuous beam of atoms with small transverse velocity to be used in atomic fountains and collision studies. One method to produce a cold continuous beam uses Zeeman effect to compensate the Doppler shift as atoms are slowed. We present a new method for producing a cold Cesium beam using Stark effect frequency tuning.

•May 8, 1994•0 citations

Cooling cesium atoms using diode lasers

Carl Wieman, R. N. Watts

We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.

International Laser Science Conference•Jan 1, 1986•0 citations

A continuous slow atomic beam for a cesium frequency standard

Sang Eon Park, Hyuck Cho, Sung-Hoon Yang +1 more

A continuous slow cesium atomic beam was produced from a thermal atomic beam by using a laser-cooling technique. This beam will be used as an atomic source of a frequency standard. The mean longitudinal velocity and the rms velocity width of the slow atoms were approximately 24 m/s and 0.9 m/s, respectively.

Conference on Precision Electromagnetic Measurements•Nov 7, 2002•1 citation

Trapping and cooling of atoms

C. J. Pethick, H. Smith

The advent of the laser opened the way to the development of powerful methods for producing and manipulating cold atomic gases. To set the stage we describe a typical experiment, which is shown schematically in Fig. 4.1. A beam of sodium atoms emerges from an oven at a temperature of about 600 K, corresponding to a speed of about 800 m s −1 , and is then passed through a so-called Zeeman slower, in which the velocity of the atoms is reduced to about 30 m s −1 , corresponding to a temperature of about 1 K. In the Zeeman slower, a laser beam propagates in the direction opposite that of the atomic beam, and the radiation force produced by absorption of photons retards the atoms. Due to the Doppler effect, the frequency of the atomic transition in the laboratory frame is not generally constant, since the atomic velocity varies. However, by applying an inhomogeneous magnetic field designed so that the Doppler and Zeeman effects cancel, the frequency of the transition in the rest frame of the atom may be held fixed. On emerging from the Zeeman slower the atoms are slow enough to be captured by a magneto-optical trap (MOT), where they are further cooled by interactions with laser light to temperatures of order 100 μK. Another way of compensating for the changing Doppler shift is to increase the laser frequency in time, which is referred to as ‘chirping’.

Cambridge University Press eBooks•Sep 11, 2008•0 citations
We report the possibility of producing a beam of slow atoms with a characteristic velocity of ∼ 1 m s − 1 by the ‘chirp’ method, namely, cooling by variable-frequency radiation. Method modifications are considered, which substantially reduce dimensions of the slower, the width of the longitudinal velocity distribution of the atomic beam, and the area of its cross section. The modified method of laser radiation frequency tuning for cooling rubidium atoms is mathematically simulated.
We have laser cooled an atomic beam of rubidium with diode lasers and have used these slow atoms to load a magneto-optical trap. The cooling is performed with the frequency-chirp method,1,2 in which the laser's frequency is ramped linearly (by the injection currant) to maintain resonance with the decelerating atoms. Two synchronously chirped lasers are required to prevent optical hyperfine pumping of the ground state. The chirp typically covers 500 MHz in 10 ms. At the end of each ramp, the resulting velocity distribution is measured with a pulsed probe laser. By varying the end point of the chirp, we are able to obtain slow atoms with average velocities ranging from 200 to −50 m/s. The widths of the velocity distributions are measured to be approximately 40 m/s. This relatively large width results from the inherent linewidth (~30 MHz) of the free-running diode lasers used for both cooling and probing.
We have cooled and stopped a beam of cesium atoms using frequency chirped diode lasers. In this technique, a moving atom absorbs and reemits many photons from a counter propagating laser that is frequency swept to keep it in resonance with an atomic transition. The resulting momentum transfer slows the atom. The basic approach is identical to that developed by Hall and co-workers, however, the use of diode lasers allows us to obtain the necessary frequency modulation simply by sweeping the laser injection current. We use two diode lasers tuned to each of the 6s hyperfine ground state levels to drive the 6s—6p3/2 transitions. Each laser is simultaneously swept over the Doppler profile of the 100°C thermal cesium beam to bring a substantial number to a stop. Using additional fast frequency modulation, the same lasers are used to probe the resulting velocity distribution. This technique allows us to bring ~106 atoms/cm3 to a temperature of 1 K. This method is an extremely simple and inexpensive way to produce cold atoms.
The advent of the laser opened the way to the development of powerful methods for producing and manipulating cold atomic gases. To set the stage we describe a typical experiment, which is shown schematically in Fig. 4.1. A beam of sodium atoms emerges from an oven at a temperature of about 600 K, corresponding to a speed of about 800 m s −1 , and is then passed through a so-called Zeeman slower, in which the velocity of the atoms is reduced to about 30 m s −1 , corresponding to a temperature of about 1 K. In the Zeeman slower, a laser beam propagates in the direction opposite that of the atomic beam, and the radiation force produced by absorption of photons retards the atoms. Due to the Doppler effect, the frequency of the atomic transition in the laboratory frame is not generally constant, since the atomic velocity varies. However, by applying an inhomogeneous magnetic field designed so that the Doppler and Zeeman effects cancel, the frequency of the transition in the rest frame of the atom may be held fixed. On emerging from the Zeeman slower the atoms are slow enough to be captured by a magneto-optical trap (MOT), where they are further cooled by interactions with laser light to temperatures of order 100 μK. Another way of compensating for the changing Doppler shift is to increase the laser frequency in time, which is referred to as ‘chirping’.