We study an electrical readout scheme for superconducting nanowire single photon detectors using commercial off-the-shelf amplifiers operating at cryogenic temperatures. Low power consumption and improved noise performance enable multichannel readout circuit solution with high timing resolution.
The superconducting nanowire single-photon detector (SNSPD) is a leading technology for quantum information science applications using photons, and is finding increasing uses in photon-starved classical imaging applications. Critical detector characteristics, such as timing resolution (jitter), reset time, and maximum count rate, are heavily influenced by the readout electronics that sense and amplify the photon detection signal. We describe a readout circuit for SNSPDs using commercial off-the-shelf amplifiers operating at cryogenic temperatures. Our design demonstrates a 35 ps timing resolution and a maximum count rate of over 2 × 107 counts per second, while maintaining <3 mW power consumption per channel, making it suitable for a multichannel readout.
Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.
Superconducting nanowire single-photon detectors (SNSPD) have the advantages of high maximal counting rate (MCR), high detection efficiency, and low dark count rate. They play an important role in the fields of optical quantum communication, optical quantum computing, laser ranging, and imaging. The MCR (i.e. detection speed) of SNSPD can be affected by the front-end readout circuit. To increase MCR, it is usually necessary to use a cryogenic DC-coupled readout circuit with a broad bandwidth. This study reports an SNSPD cryogenic DC-coupled amplification readout circuit based on a commercial high-speed operational amplifier chip OPA855. We systematically characterize its performance parameters in a temperature range from a room temperature of 300 K to a low temperature of 4.2 K. We address the problem of bandwidth loss of the circuit in a low-temperature environment by increasing the operating voltage of the OPA855 chip. For example, at 40 K, the operating voltage increases from ±2.5 V to ±4.9 V, and the quiescent current is about 8 mA, which is equivalent to a power consumption of 78 mW; meanwhile, the gain of this readout circuit is 16.7 dB, and the –3 dB cutoff bandwidth is ~2.7 GHz. We further install a cryogenic DC-coupled readout circuit based on the OPA855 amplifier at 40 K and characterize the performance parameters of the SNSPD at 2.2 K, such as the switching current, system detection efficiency, and MCR. The comparison with the conventional AC-coupled readout circuit at room temperature shows that the MCR increases about 1.3 times after using the DC-coupling circuit. Our study provides the interesting information about the OPA855 amplifier’s performance at low temperatures which facilitates its application in cryogenic environments and related fields.
We demonstrate the transfer of single photon triggered electrical pulses from a superconducting nanowire single photon detector (SNSPD) to a single flux quantum (SFQ) pulse. We describe design and test of a digital SFQ based SNSPD readout circuit and demonstrate its correct operation. Both circuits (SNSPD and SFQ) operate under the same cryogenic conditions and are directly connected by wire bonds. A future integration of the present multi-chip configuration seems feasible because both fabrication process and materials are very similar. In contrast to commonly used semiconductor amplifiers, SFQ circuits combine very low power dissipation (a few microwatts) with very high operation speed, thus enabling count-rates of several gigahertz. The SFQ interface circuit simplifies the SNSPD readout and enables large numbers of detectors for future compact multi-pixel systems with single photon counting resolution. The demonstrated circuit has great potential for scaling the present interface solution to 1,000 detectors by using a single SFQ chip.
Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.
Abstract Scalable, low power, high speed data transfer between cryogenic (0.1–4 K) and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1,000–10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD.