Introduction When an electromagnetic wave propagates through amedium stimulated emissions increase the intensity of the wave, while absorptions diminish it. The overall intensity will increase if the number of stimulated emissions can be made larger than the number of absorptions. If we can create such a situation then we have built an amplifier that operates through the mechanism of stimulated emission. This laser amplifier , in common with electronic amplifiers, has useful gain only over a particular frequency bandwidth. Its operating frequency range will be determined by the lineshape of the transition, and we expect the frequency width of its useful operating range to be of the same order as the width of the lineshape. It is very important to consider how this frequencywidth is related to the various mechanisms by which transitions between different energy states of a particle are smeared out over a range of frequencies. This line broadening affects in a fundamental way not only the frequency bandwidth of the amplifier, but also its gain. A laser amplifier can be turned into an oscillator by supplying an appropriate amount of positive feedback. The level of oscillation will stabilize because the amplifier saturates. Laser amplifiers fall into two categories, which saturate in different ways. A homogeneously broadened amplifier consists of a number of amplifying particles that are essentially equivalent, whereas an inhomogeneously broadened amplifier contains amplifying particles with a distribution of amplification characteristics. Homogeneous line broadening All energy states, except the lowest energy state of a particle (the ground state) cover a range of possible energies.
Introduction When an electromagnetic wave propagates through amedium stimulated emissions increase the intensity of the wave, while absorptions diminish it. The overall intensity will increase if the number of stimulated emissions can be made larger than the number of absorptions. If we can create such a situation then we have built an amplifier that operates through the mechanism of stimulated emission. This laser amplifier , in common with electronic amplifiers, has useful gain only over a particular frequency bandwidth. Its operating frequency range will be determined by the lineshape of the transition, and we expect the frequency width of its useful operating range to be of the same order as the width of the lineshape. It is very important to consider how this frequencywidth is related to the various mechanisms by which transitions between different energy states of a particle are smeared out over a range of frequencies. This line broadening affects in a fundamental way not only the frequency bandwidth of the amplifier, but also its gain. A laser amplifier can be turned into an oscillator by supplying an appropriate amount of positive feedback. The level of oscillation will stabilize because the amplifier saturates. Laser amplifiers fall into two categories, which saturate in different ways. A homogeneously broadened amplifier consists of a number of amplifying particles that are essentially equivalent, whereas an inhomogeneously broadened amplifier contains amplifying particles with a distribution of amplification characteristics. Homogeneous line broadening All energy states, except the lowest energy state of a particle (the ground state) cover a range of possible energies.
Introduction Previous discussions (see Section 10.4) suggested that stimulated emission can be used to generate optical gain, that is, to amplify radiation. The reader certainly has experience in the amplification of electronic signal. For example, radio receivers capture faint radio waves and turn them into a signal that is powerful enough to drive large speakers. This electronic amplification increases the amplitude of the signal while faithfully preserving its acoustic frequencies and modulation characteristics. Similarly, optical amplification is expected to increase the amplitude of an optical signal while preserving its frequency, its modulation characteristics, and its coherence. The latter requirement is of particular significance for optical radiation, where the coherence of naturally occurring radiation rarely exceeds one micrometer. Lasers are the primary source for coherent radiation. They depend on stimulated emission for amplification and for the generation of coherent radiation (the word laser is the acronym of Light Amplification by Stimulated Emission of Radiation). For amplification, an atomic system that is part of the laser medium must be prepared with a sufficiently large number of particles in the excited state. (The term atomic system is used here to describe all microscopic systems including molecules and free electrons.) Radiation passing through that excited medium encounters multiple events of stimulated emission, each event contributing one photon that is added coherently to the propagating beam. When the number of events of stimulated emission exceed all losses by absorption or scattering, the incident radiation is amplified.
All optical oscillators and amplifiers can be analyzed as an electromagnetic structure, such as a cavity or a transmission line, which contains an amplifying medium. The operating characteristics of lasers are governed by both the electromagnetic properties of the structures and the properties of the amplifying medium. Stimulated emission and absorption of radiation from energy states are the physical basis of amplification in all laser materials. In order to study lasers, it is necessary to understand the energy levels of the amplifying medium and the stimulated transitions involving them. Quantum mechanical analysis of the energy states and the stimulated emission and absorption is presented in most books on lasers. However, quantum mechanical analyses cover only the analysis of individual atoms. We need to relate the effects of the quantum mechanical interactions to the macroscopic properties of the materials so that properties of the lasers may be analyzed. Therefore, the macroscopic susceptibility of materials related to stimulated emission and absorption is the focus of discussion in this chapter. It is not the purpose of this book to teach quantum mechanics. There are already many excellent books on this topic. The readers are assumed to have a fundamental knowledge of quantum mechanics. However, it is necessary first to review some of the major steps in order to understand precisely the notation used and the meaning of the results. This is presented in Section 5.1.
Introduction In this chapter we will present the theory of spectral gain in optical amplifiers and the related optical power distribution. The concepts are general, as they apply to every optical amplifier configuration, independent of the specific architecture and implementation technology. We will configure the optical amplifying medium as a traveling-wave device, where the optical field undergoes optical amplification as it propagates from the input to the output sections. Generally speaking, optical amplification is achieved by a net stimulated emission process. Referring to a generic section z of infinitesimal thickness dz , optical gain is determined by the imbalance between net stimulated emission and cavity losses, including extrinsic absorption, reflection and radiated fields. As we know from the theory of light amplification in the three-level atomic system presented in Chapter 5, stimulated absorption of photons is governed by the same transition rate as stimulated emission, and is included in the net stimulated emission process. With this in mind, we note the identity between stimulated emission and the stimulated absorption rates, Γ 12 = Γ 21 , and the net stimulated photon term Γ[ j 2 ( t ) – j 1 ( t )] p ( t ) in the rate equation. In order to develop the traveling-wave model, the photon density becomes a function of the longitudinal position 0 ≤ z ≤ L along the amplifier medium. Accordingly, we will set p ( t , z ) as the relative density of stimulated photons per unit volume (0 ≤ p ( t , z ) ≤ 1) at time t and section z . When photons with appropriate energy proceed along the amplifying medium, they are amplified by means of net stimulated emission. At some section z = z 0 , the steady-state photon density P ( z ) can approach the saturation density P sat ( z ).
Introduction We were able to show in Chapter 3 that a medium in which we can obtain a population inversion (i.e. a situation in which the population density in the excited state is greater than that in the fundamental level) allows for optical gain of an electromagnetic wave having a frequency near to the resonant frequency of the system. By introducing feedback of the amplified signal into the medium, the system can be made to oscillate naturally, resulting in laser oscillations . To obtain this population inversion, we must introduce at least a third (and perhaps even a fourth) energy level into the system. (We saw how a two-level system under the influence of an intense pump beam will saturate with no resulting population inversion.) The aim then of this chapter is to introduce the concepts necessary to extend our two-level system into a working model capable of illustrating the phenomenon of laser oscillation. We will not spend too much time discussing atomic transition lasers as they do not figure readily in our treatment of quantum electronic properties of semiconductors. An exception will be made, however; we brush upon the particular topics of a diode pumped laser in Complement 4.E and a quantum cascade laser in Complement 13.H. Population inversion and optical amplification Population inversion We will show how population inversion can be achieved by carrier transfer from higher lying levels to the upper level of a two-level subsystem of interest.
This chapter begins with a heuristic derivation of atomic population rate equations which include changes to level populations due to stimulated transitions as well as level relaxations and pump. These equations are used to study the saturation of population inversion with increasing light intensity and its dependence on the type of gain medium (three-level gain media vs. four-level gain media), lineshape and nature of line broadening (homogeneous vs inhomogeneous broadening). How saturation affects lineshape and thus gain and absorption giving rise to phenomena like power broadening and spectral hole burning is also discussed. The chapter summarizes the equations of motion for atomic polarization, inversion and the cavity field describing their nonlinear dynamical coupling. These equations, known as the Maxwell-Bloch equations, provide a complete description of atom-field interaction in a laser. Approximations of these equations, including the rate equation approximation, to deal with different laser classes are briefly described. These will be used in the next few chapters to explore and understand the rich and varied behavior of lasers. The chapter ends with a summary of select gain media for different types of commonly used lasers.
The theory of the laser amplifier is developed for conditions in which the strength of the input signal is increased from small values, where the amplification is linear, to larger values, where the amplification becomes nonlinear. The below-threshold laser amplifier oscillates at a single frequency equal to that of the input signal, and its properties are found by solution of the nonlinear equation of motion for the single excitation amplitude. For the above-threshold laser amplifier, the effects of the nonlinear behavior are to shift the laser frequency from its free-running value and to transfer intensity from the laser line to the signal frequency and to a range of satellite lines, whose frequency detunings are integer multiples of the signal detuning. The intensities of the various emission lines of the laser are calculated by power-series expansions of the field amplitudes up to terms of fourth order in the input signal strength. The onset of injection locking is determined by the conditions for which the intensity at the shifted free-running laser frequency falls to zero. The injection-locked state is characterized by a single excitation frequency equal to that of the input signal, and its properties are found by solution of the same nonlinear equation of motion as for the below-threshold amplifier. The ranges of input signal strength and detuning are determined for which the injection-locked state is stable. The energy conservation properties of the laser amplifier are considered for each of its operating states. \textcopyright{} 1996 The American Physical Society.