Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Superconductive Electronics Conference (ISEC)

SFQ Amplified Circuit for Photon-Number-Resolving SNSPD Array

Kazuki Ota, Masato Naruse, Tohru Taino, Jian Chen, Lin Kang, Peiheng Wu, Hiroaki Myoren

Published Jul 1, 2015• 3 citations
Publisher

Abstract

Superconducting nanowire single-photon detectors (SNSPDs) with series-parallel meander-type configuration are demonstrated to have photon-number- resolving (PNR) capabilities. Based on this unique feature, SNSPDs are expected to be used in the evaluation of single photon sources. However, increasing the number of SNSPDs causes an increase in the heat flow and further degradation in the timing jitter. To resolve this problem, the use of single flux quantum (SFQ) logic circuits is proposed. In this study, we present the read-out circuit for the SNSPD array, based on the SFQ logic. Our design of the read- out circuit makes it feasible to simultaneously process six SNSPD signals at 500 MHz and amplify the output voltage as an input to other circuits without the need for any amplifiers. We confirm using simulations that our designed read-out circuit has these capabilities. Furthermore, it is shown that the output voltage increases by 4.8 mV, proportional to the number of SNSPD signals and the output voltage is between 4.8 and 27.8 mV.

DOI
10.1109/isec.2015.7383479

Related papers

Readout Circuit Based on Single-Flux-Quantum Logic Circuit for Photon-Number-Resolving SNSPD Array

Hiroaki Myoren, Satoshi Denda, Kazuki Ota +5 more

A read-out circuit for photon-number-resolving superconducting nanowire single-photon detector (SNSPD) based on the single-flux-quantum (SFQ) circuit was designed and the basic performance of the fabricated circuit was confirmed. The current pulse output from an SNSPD array was converted to a SFQ pulse. The SFQ pulse triggered two stacks of double-flux-quantum (DFQ) amplifiers. A single block of a 40-series DFQ amplifier (DFQA) generated 2.3-mV voltage with a rising time of 400 ps for an operation frequency of 1.25 GHz, and the two stacks of DFQA generated 4.6-mV voltage when the SFQ pulse trains supplied both the DFQAs. The total voltage generated by twelve-series of 40-series DFQAs was expected to be 27.6 mV, with the same rising time of 400 ps. Using the fabricated circuit, the 40-series DFQA and the two stacks of the 40-series DFQA generated 2.3- and 4.6-mV voltage, respectively. The output voltage of the SFQ readout circuit was compatible to a room-temperature photon counter with a wide-band low-noise amplifier operating at low temperature.

IEEE Transactions on Applied Superconductivity•Mar 2, 2018•11 citations

Single-Flux Quantum Readout Circuits for Photon-Number-Resolving Superconducting Nanowire Single-Photon Detectors

Hiroaki Myoren, Shunsuke Takeda, Masato Naruse +3 more

Superconducting nanowire single-photon detectors (SNSPDs) with series-parallel meander-type configurations are demonstrated to have photon-number-resolving capabilities and are expected to be used for an evaluation system of single-photon generators and/or an energy-resolved fast detector for a new-generation time-of-flight mass spectrometry. In this paper, we present the design, fabrication, and confirmation of correct operations of two kinds of single-flux-quantum (SFQ) digital readout circuits for an SNSPD with a series-parallel meander-type configuration. Assuming a six-parallel meander-type configuration, we designed: a six-level current discriminator using six different magnetically coupled DC/SFQ converter circuits; and a Δ-type A/D converter using a quasi-one-junction SQUID (QOS) comparator with an SFQ feedback loop. For the design of the magnetically coupled inputs, we used a 3-D inductance extraction program FastHenry and the designed circuits were fabricated using a HYPRES 4.5-kA/cm2Nb process and a National Institute of Advanced Industrial Science and Technology (AIST) standard 2.5-kA/cm2Nb process.

IEEE Transactions on Applied Superconductivity•Oct 28, 2014•10 citations

Photon number resolvability of multi-pixel superconducting nanowire single photon detectors using a single flux quantum circuit

Hou-Rong Zhou, Kun-Jie Cheng, Jie Ren +5 more

Superconducting nanowire single-photon detectors (SNSPDs) are typical switching devices capable of detecting single photons with almost 100% detection efficiency. However, they cannot determine the exact number of incident photons during a detection event. Multi-pixel SNSPDs employing multiple read-out channels can provide photon number resolvability (PNR), but they require increased cooling power and costly multi-channel electronic systems. In this work, a single-flux quantum (SFQ) circuit is employed, and PNR based on multi-pixel SNSPDs is successfully demonstrated. A multi-input magnetically coupled DC/SFQ converter (MMD2Q) circuit with a mutual inductance M is used to combine and record signals from a multi-pixel SNSPD device. The designed circuit is capable of discriminating the amplitude of the combined signals in accuracy of Φ 0/M with Φ 0 being a single magnetic flux quantum. By employing the MMD2Q circuit, the discrimination of up to 40 photons can be simulated. A 4-parallel-input MMD2Q circuit is fabricated, and a PNR of 3 is successfully demonstrated for an SNSPD array with one channel reserved for the functional verification. The results confirm that an MMD2Q circuit is an effective tool for implementing PNR with multi-pixel SNSPDs.

Chinese Physics B•Nov 15, 2021•3 citations

Improving photon number resolvability of a superconducting nanowire single-photon detector array using a level comparator circuit

Jia Huang, Xingyu Zhang, Weijun Zhang +7 more

Abstract Photon number resolving (PNR) capability is very important in many optical applications, including quantum information processing, fluorescence detection, and few-photon-level ranging and imaging. Superconducting nanowire single-photon detectors (SNSPDs) with a multipixel interleaved architecture give the array an excellent spatial PNR capability. However, the signal-to-noise ratio (SNR) of the PNR (SNRPNR) of the array will be degraded with increasing the element number due to the electronic noise in the readout circuit, which limits the PNR resolution as well as the maximum PNR number. In this study, a 16-element interleaved SNSPD array was fabricated, and the PNR capability of the array was investigated and analyzed. By introducing a level comparator circuit (LCC), the SNRPNR of the detector array was improved over a factor of four. In addition, we performed a statistical analysis of the photon number on this SNSPD array with LCC, showing that the LCC method effectively enhances the PNR resolution. Besides, the system timing jitter of the detector was reduced from 90 ps to 72 ps due to the improved electrical SNR.

Superconductor Science and Technology•Apr 9, 2024•7 citations

Readout Electronics Using Single-Flux-Quantum Circuit Technology for Superconducting Single-Photon Detector Array

Hirotaka Terai, Shigehito Miki, Zhen Wang

Superconducting single-photon detectors (SSPDs) based on NbN nanowires possess properties such as high counting rate, low dark count rate and small timing jitter, which are promising characteristics for a quantum key distribution system. An SSPD array has recently attracted attention, because it can provide a higher counting rate, and spatial and photon-number resolutions. We propose readout electronics using single-flux-quantum (SFQ) circuits to process a large number of output signals from an SSPD array. We designed and tested an interface circuit between an SSPD and SFQ circuit, and successfully observed SFQ pulse generation for an input pulse with a current amplitude of 17.4 ~ 36.4 muA , which is comparable with an output current amplitude of the SSPD. The interface circuit was also operational for an input pulse duration of 1.6 ns, which is shorter than the typical recovery time of the SSPD.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•63 citations

Technologies for superconducting nanowire single-photon detector array system

Shigehito Miki, Taro Yamashita, Hirotaka Terai +2 more

We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 3, 2013•1 citation
Superconducting nanowire single-photon detectors (SNSPDs) with series-parallel meander-type configuration are demonstrated to have photon-number- resolving (PNR) capabilities. Based on this unique feature, SNSPDs are expected to be used in the evaluation of single photon sources. However, increasing the number of SNSPDs causes an increase in the heat flow and further degradation in the timing jitter. To resolve this problem, the use of single flux quantum (SFQ) logic circuits is proposed. In this study, we present the read-out circuit for the SNSPD array, based on the SFQ logic. Our design of the read- out circuit makes it feasible to simultaneously process six SNSPD signals at 500 MHz and amplify the output voltage as an input to other circuits without the need for any amplifiers. We confirm using simulations that our designed read-out circuit has these capabilities. Furthermore, it is shown that the output voltage increases by 4.8 mV, proportional to the number of SNSPD signals and the output voltage is between 4.8 and 27.8 mV.
A read-out circuit for photon-number-resolving superconducting nanowire single-photon detector (SNSPD) based on the single-flux-quantum (SFQ) circuit was designed and the basic performance of the fabricated circuit was confirmed. The current pulse output from an SNSPD array was converted to a SFQ pulse. The SFQ pulse triggered two stacks of double-flux-quantum (DFQ) amplifiers. A single block of a 40-series DFQ amplifier (DFQA) generated 2.3-mV voltage with a rising time of 400 ps for an operation frequency of 1.25 GHz, and the two stacks of DFQA generated 4.6-mV voltage when the SFQ pulse trains supplied both the DFQAs. The total voltage generated by twelve-series of 40-series DFQAs was expected to be 27.6 mV, with the same rising time of 400 ps. Using the fabricated circuit, the 40-series DFQA and the two stacks of the 40-series DFQA generated 2.3- and 4.6-mV voltage, respectively. The output voltage of the SFQ readout circuit was compatible to a room-temperature photon counter with a wide-band low-noise amplifier operating at low temperature.
Superconducting nanowire single-photon detectors (SNSPDs) with series-parallel meander-type configurations are demonstrated to have photon-number-resolving capabilities and are expected to be used for an evaluation system of single-photon generators and/or an energy-resolved fast detector for a new-generation time-of-flight mass spectrometry. In this paper, we present the design, fabrication, and confirmation of correct operations of two kinds of single-flux-quantum (SFQ) digital readout circuits for an SNSPD with a series-parallel meander-type configuration. Assuming a six-parallel meander-type configuration, we designed: a six-level current discriminator using six different magnetically coupled DC/SFQ converter circuits; and a Δ-type A/D converter using a quasi-one-junction SQUID (QOS) comparator with an SFQ feedback loop. For the design of the magnetically coupled inputs, we used a 3-D inductance extraction program FastHenry and the designed circuits were fabricated using a HYPRES 4.5-kA/cm2Nb process and a National Institute of Advanced Industrial Science and Technology (AIST) standard 2.5-kA/cm2Nb process.
Superconducting nanowire single-photon detectors (SNSPDs) are typical switching devices capable of detecting single photons with almost 100% detection efficiency. However, they cannot determine the exact number of incident photons during a detection event. Multi-pixel SNSPDs employing multiple read-out channels can provide photon number resolvability (PNR), but they require increased cooling power and costly multi-channel electronic systems. In this work, a single-flux quantum (SFQ) circuit is employed, and PNR based on multi-pixel SNSPDs is successfully demonstrated. A multi-input magnetically coupled DC/SFQ converter (MMD2Q) circuit with a mutual inductance M is used to combine and record signals from a multi-pixel SNSPD device. The designed circuit is capable of discriminating the amplitude of the combined signals in accuracy of Φ 0/M with Φ 0 being a single magnetic flux quantum. By employing the MMD2Q circuit, the discrimination of up to 40 photons can be simulated. A 4-parallel-input MMD2Q circuit is fabricated, and a PNR of 3 is successfully demonstrated for an SNSPD array with one channel reserved for the functional verification. The results confirm that an MMD2Q circuit is an effective tool for implementing PNR with multi-pixel SNSPDs.
Abstract Photon number resolving (PNR) capability is very important in many optical applications, including quantum information processing, fluorescence detection, and few-photon-level ranging and imaging. Superconducting nanowire single-photon detectors (SNSPDs) with a multipixel interleaved architecture give the array an excellent spatial PNR capability. However, the signal-to-noise ratio (SNR) of the PNR (SNRPNR) of the array will be degraded with increasing the element number due to the electronic noise in the readout circuit, which limits the PNR resolution as well as the maximum PNR number. In this study, a 16-element interleaved SNSPD array was fabricated, and the PNR capability of the array was investigated and analyzed. By introducing a level comparator circuit (LCC), the SNRPNR of the detector array was improved over a factor of four. In addition, we performed a statistical analysis of the photon number on this SNSPD array with LCC, showing that the LCC method effectively enhances the PNR resolution. Besides, the system timing jitter of the detector was reduced from 90 ps to 72 ps due to the improved electrical SNR.
Superconducting single-photon detectors (SSPDs) based on NbN nanowires possess properties such as high counting rate, low dark count rate and small timing jitter, which are promising characteristics for a quantum key distribution system. An SSPD array has recently attracted attention, because it can provide a higher counting rate, and spatial and photon-number resolutions. We propose readout electronics using single-flux-quantum (SFQ) circuits to process a large number of output signals from an SSPD array. We designed and tested an interface circuit between an SSPD and SFQ circuit, and successfully observed SFQ pulse generation for an input pulse with a current amplitude of 17.4 ~ 36.4 muA , which is comparable with an output current amplitude of the SSPD. The interface circuit was also operational for an input pulse duration of 1.6 ns, which is shorter than the typical recovery time of the SSPD.
We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.