The quantum efficiency of photon counters can be measured with standard uncertainty below 1% level using correlated photon pairs generated through spontaneous parametric down-conversion process. Normally a laser in UV, blue or green wavelength range with sufficient photon energy is applied to produce energy and momentum conserved photon pairs in two channels with desired wavelengths for calibration. One channel is used as the heralding trigger, and the other is used for the calibration of the detector under test. A superconducting nanowire single photon detector with advantages such as high photon counting speed (<20 MHz), low dark count rate (<50 counts per second), and wideband responsivity (UV to near infrared) is used as the trigger detector, enabling correlated photons calibration capabilities into shortwave visible range. For a 355nm single longitudinal mode pump laser, when a superconducting nanowire single photon detector is used as the trigger detector at 1064nm and 1560nm in the near infrared range, the photon counting efficiency calibration capabilities can be realized at 532nm and 460nm. The quantum efficiency measurement on photon counters such as photomultiplier tubes and avalanche photodiodes can be then further extended in a wide wavelength range (e.g. 400-1000nm) using a flat spectral photon flux source to meet the calibration demands in cutting edge low light applications such as time resolved fluorescence and nonlinear optical spectroscopy, super resolution microscopy, deep space observation, and so on.
The quantum efficiency of photon counters can be measured with standard uncertainty below 1% level using correlated photon pairs generated through spontaneous parametric down-conversion process. Normally a laser in UV, blue or green wavelength range with sufficient photon energy is applied to produce energy and momentum conserved photon pairs in two channels with desired wavelengths for calibration. One channel is used as the heralding trigger, and the other is used for the calibration of the detector under test. A superconducting nanowire single photon detector with advantages such as high photon counting speed (<20 MHz), low dark count rate (<50 counts per second), and wideband responsivity (UV to near infrared) is used as the trigger detector, enabling correlated photons calibration capabilities into shortwave visible range. For a 355nm single longitudinal mode pump laser, when a superconducting nanowire single photon detector is used as the trigger detector at 1064nm and 1560nm in the near infrared range, the photon counting efficiency calibration capabilities can be realized at 532nm and 460nm. The quantum efficiency measurement on photon counters such as photomultiplier tubes and avalanche photodiodes can be then further extended in a wide wavelength range (e.g. 400-1000nm) using a flat spectral photon flux source to meet the calibration demands in cutting edge low light applications such as time resolved fluorescence and nonlinear optical spectroscopy, super resolution microscopy, deep space observation, and so on.
For photon-counting applications at ultraviolet wavelengths, there are currently no detectors that combine high efficiency (> 50%), sub-nanosecond timing resolution, and sub-Hz dark count rates. Superconducting nanowire single-photon detectors (SNSPDs) have seen success over the past decade for photon-counting applications in the near-infrared, but little work has been done to optimize SNSPDs for wavelengths below 400 nm. Here, we describe the design, fabrication, and characterization of UV SNSPDs operating at wavelengths between 250 and 370 nm. The detectors have active areas up to 56 μm in diameter, 70 - 80% efficiency at temperatures up to 4.2 K, timing resolution down to 60 ps FWHM, blindness to visible and infrared photons, and dark count rates of ∼ 0.25 counts/hr for a 56 μm diameter pixel. These performance metrics make UV SNSPDs ideal for applications in trapped-ion quantum information processing, lidar studies of the upper atmosphere, UV fluorescent-lifetime imaging microscopy, and photon-starved UV astronomy.
Superconducting single-photon detectors have been shown to have extremely high detection efficiency over a large wavelength range, typically exceeding 90 % [1, 2]. Their use in quantum and classical optics is becoming more and more widespread in part due to improvements to and ease of use of the cryogenic packaging. In this talk, we will review two superconducting detector technologies, the superconducting nanowire single-photon detector (SNSPD) and the optical transition-edge sensor (TES) [3], that are being developed at NIST. We will also describe their applications in quantum and classical optics and present our recent effort to use these detectors as calibration standards, as well as our effort to establish a single-photon detector calibration service. Superconducting Nanowire Single Photon Detectors The SNSPD is based on a meandering, narrow, thin superconducting nanowire, current-biased close to its critical current. Our SNSPDs operate at temperatures around 1K. When a photon is absorbed in the detection region, the energy deposited drives the wire normal and a voltage pulse can be observed. Due to the speed of the detection process, the SNSPD offers high timing resolution along with detection of the photon flux at the shot-noise limit. The combination of both these features yields a detector that can measure the photon’s arrival time from a faint object or source. SNSPDs also offer single-photon detection capability beyond the wavelength detection range of silicon and InGaAs, out to at least 5000 nm [4]. SNSPDs were also recently implemented in an 8×8-pixel array enabling low-resolution, real-time imaging [5]. For our calibration service effort, we built an SNSPD system that can be used as a transfer standard between labs for single-photon detector calibrations. Transition Edge Sensors In contrast to the SNSPD, the TES is a photon-number resolving detector that has almost unity detection efficiency. The TES consists of a superconducting thin film, voltage-biased so that its resistance is in the transition between the superconducting regime and the normal conducting regime. The steep slope of the resistive transition allows for small temperature changes to be measured. The TES is designed such that the absorption of a single photon increases the temperature of the superconducting film enough to discern the resulting signal from the TES system noise. Therefore, the TES needs to be electrically and thermally quiet and is generally operated at temperatures around 100 mK. Due to its energy resolving capability, the TES can be also used as a spectrally resolving single-photon detector with limited resolution [6]. The TES can also be operated as a cryogenic radiometer in combination with an electrical substitution method, and can, in principle, yield absolute calibration of optical powers on the order of a few tens of femtowatts [7]. References 1 A. E. Lita, A. J. Miller, and S. W. Nam, Opt. Express 16, 3032 (2008). 2 F. Marsili, et al., Nat Photon 7, 210 (2013). 3 R. Hadfield and G. Johansson, Superconducting Devices in Quantum Optics (Springer, 2016). 4 F. Marsili, et al., in CLEO: 2013 (OSA, San Jose, California, 2013), p. CTu1H.1. 5 M. S. Allman, et al., Applied Physics Letters 106, 192601 (2015). 6 M. Fortsch, et al., Journal of Optics 17, 065501 (2015). 7 N. A. Tomlin, J. H. Lehman, and S. Nam, Optics Letters 37, 2346 (2012).
Single-photon counting has become an essential tool in quantum optics experiments, as well as remote sensing and life science applications. However conventional technologies such as single-photon avalanche diodes, as well as the availability of standard telecom optical components, has limited much of this work to the near infrared/telecom wavelength range. Superconducting nanowire single photon detectors (SNSPDs) have emerged in recent years as the gold standard in photon counting applications due to their low dark count rates, fast timing resolution and high efficiency [1]. SNSPDs have also demonstrated photon counting efficiency out to much greater wavelengths which enables us to explore new experimental possibilities in the mid-infrared [2]. In this work we design and fabricate mid-infrared SNSPDs and deploy them in a variety of photon counting experiments [3,4]. The devices are based on a NbTiN superconducting film integrated into an optical cavity to enhance absorption in the mid-infrared. We characterise these devices using an optical parametric oscillator, tuneable between 1.5 m and 4.2 m. We then deploy these in a proof-of-principle tabletop light detection and ranging (LIDAR) experiment at 2.3 m. LIDAR in the mid-infrared is attractive due to spectral regions of low atmospheric absorption and reduced solar background photon flux, when compared to telecom wavelengths. We also present results from a photon-pair source operating at 2 m. This is a key resource for extending quantum optics and quantum secure communications to the mid infrared domain. Pairs are generated using a custom lithium niobate crystal and detected using SNSPDs. We demonstrate two-photon interference and polarisation entanglement of the photon pairs at 2 m. This work opens the pathway to future development of quantum optics and quantum technologies in the mid-infrared spectral region. References [1] Gol’tsman et al Applied Physics Letters 79 705 (2001) [2] Marisli et al Nano Letters 12 (9) 4799 (2012) [3] G. G. Taylor et al Optics Express 26 (27) 38147 (2018) [4] S. Prabhakar et al Science Advances 6 (13) eaay5195 (2019)
We present a new class of single-photon devices for counting of both visible and infrared photons. Our superconducting single-photon detectors (SSPDs) are characterized by the intrinsic quantum efficiency (QE) reaching up to 100%, above 10 GHz counting rate, and negligible dark counts. The detection mechanism is based on the photon-induced hotspot formation and subsequent appearance of a transient resistive barrier across an ultrathin and submicron-wide superconducting stripe. The devices are fabricated from 3.5-nm-thick NbN films and operate at 4.2 K, well below the NbN superconducting transition temperature. Various continuous and pulsed laser sources in the wavelength range from 0.4 μm up to >3 μm were implemented in our experiments, enabling us to determine the detector QE in the photon-counting mode, response time, and jitter. For our best 3.5-nm-thick, 10×10 μm2-area devices, QE was found to reach almost 100% for any wavelength shorter than about 800 nm. For longer-wavelength (infrared) radiation, QE decreased exponentially with the photon wavelength increase. Time-resolved measurements of our SSPDs showed that the system-limited detector response pulse width was below 150 ps. The system jitter was measured to be 35 ps. In terms of the counting rate, jitter, and dark counts, the NbN SSPDs significantly outperform their semiconductor counterparts. Already identifeid and implemented applications of our devices range from noninvasive testing of semiconductor VLSI circuits to free-space quantum communications and quantum cryptography.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
The realization of an ultralow-dark-count rate (DCR) along with the conservation of high detection efficiency (DE) is critical for many applications using single photon detectors in quantum information technologies, material sciences, and biological sensing. For this purpose, a fiber-coupled superconducting nanowire single-photon detector (SNSPD) with a meander-type niobium nitride nanowire (width: 50 nm) is studied. Precise measurements of the bias current dependence of DE are carried out for a wide spectral range (from 500 to 1650 nm in steps of 50 nm) using a white light source and a laser line Bragg tunable band-pass filter. An ultralow DCR (0.0015 cps) and high DE (32%) are simultaneously achieved by the SNSPD at a wavelength of 500 nm.