Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Noise properties of HTS Josephson mixers at 345 GHz and operating temperatures at 20 K

Jens Scherbel, Marian Darula, Oliver Harnack, M. Siegel

Published Jun 1, 2002• 24 citations
Publisher

Abstract

The authors report on the mixing properties of high-temperature superconductor bicrystal Josephson junctions at 345 GHz and high-operating temperatures. A variable backshort and E-plane tuner enabled the control of impedance matching between the junction and the RF environment. The local oscillator frequency and intermediate frequency were 345 and 1.4 GHz, respectively. The double-side band (DSB) mixer noise temperature and the conversion efficiency were determined using the hot/cold method. The authors observed that the noise temperature was strongly dependent on the matching conditions. The lowest noise temperatures were observed for tuner positions supporting the formation of a subharmonic step which appeared between the zeroth and first Shapiro step. At T = 20 K they obtained a lowest DSB mixer noise temperature of 1003 K and a conversion efficiency of -1.2 dB. They have investigated the dependence of the noise temperature on the operating temperature in detail. The impact of resonances on the device performance will be discussed.

DOI
10.1109/tasc.2002.1020345

Related papers

Noise and Conversion Efficiency of High-T c Superconductor Josephson Mixers

Oliver Harnack, S. Beuven, Marian Darula +4 more

We report on experimental studies of the noise performance and conversion efficiency of high-Te Josephson mixers at frequencies between 90 GHz and 550 GHz. The heterodyne mixing experiments have been performed by using YBa2Cu307_8 step-edge junctions and bicrystal junctions on MgO (E--9.6) substrates. We studied the Josephson mixer performance for the case of internal pumping (selfpumping) and external pumping. Receiver noise measurements in a waveg,uide setup for the case of external pumping at 90-94 GHz gave formally calculated double-side-band (DSB) mixer noise temperatures (Tm) of about 2000 K at physical temperatures of 10 K. Similar measurements in a quasioptical setup at 4.2 K and at operation frequencies of 430 GHz and 546 GHz yielded mixer noise temperatures of 1200 K and 1100 K, respectively. Using the internal pumped mode, i.e. mixing without external local oscillator signal, we also obtained clear IF response in hot/cold-measurements. The formally calculated Tm were between 580 K and 2300 K.

Softwaretechnik-Trends•Mar 1, 1998•1 citation

Optimization of a 115 GHz waveguide mixer based on an HTS Josephson junction

Oliver Harnack, Marian Darula, Jens Scherbel +4 more

A waveguide mixer based on a Josephson junction made from a high-temperature superconductor (HTS) has been analysed at frequencies of 90 GHz and 115 GHz. The mixer consisted of a single-grain-boundary bicrystal junction which was integrated with a bow-tie antenna and a microstrip filter structure fabricated on an MgO substrate. Two different designs of mixer block were tested. Using the first design the best noise performance was measured at a local oscillator (LO) frequency of about 90 GHz. At the projected LO frequency of 115 GHz significant deterioration of performance was observed. A computer simulation of the mixer chip and substrate channel structure was performed using the 3D simulation program HFSS. Sufficient RF signal rejection by the filter structure was confirmed at 90 GHz. After a simulation cycle at 115 GHz the substrate channel in the mixer block was modified. Using this second design we measured a double-sideband mixer noise temperature of 1090 K at 10 K operating temperature which is the best performance of an HTS Josephson mixer to date obtained at this frequency and temperature.

Superconductor Science and Technology•Nov 1, 1999•25 citations

Noise and conversion properties of Y–Ba–Cu–O Josephson mixers at operating temperatures above 20 K

Oliver Harnack, Marian Darula, Stephan Beuven +1 more

We have measured the noise performance and conversion efficiency of Y–Ba–Cu–O bicrystal Josephson mixers at operating temperatures between 20 and 60 K and at operating frequencies around 90 GHz. A double-sideband mixer noise temperature of about 1600 K and a conversion efficiency of −10 dB at 20 K operating temperature has been measured using the Y-factor method. The absorbed local oscillator power was in the range of 10 nW. The dependence of the mixer performance on the normalized frequency Ω and the fluctuation parameter Γ has been studied. In accordance with the resistively shunted junction model, the experimental data show the presence of excess noise. The temperature dependence of the mixer noise temperature can be explained by the variation of the linewidth of the Josephson oscillations with the operating temperature.

Applied Physics Letters•Mar 27, 2000•12 citations

Performance of a two-junction array SIS-mixer operating around 345 GHz

Cornelia E. Honingh, Gert J. de Lange, M. M. T. M. Dierichs +3 more

The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1993•14 citations

Noise and conversion performance of a high-Tc superconducting Josephson junction mixer at 0.6 THz

Xiang Gao, Jia Du, Ting Zhang +1 more

This letter presents both theoretical and experimental investigations on the noise and conversion performance of a high-Tc superconducting (HTS) step-edge Josephson-junction mixer at the frequency of 0.6 THz and operating temperatures of 20–40 K. Based on the Y-factor and U-factor methods, a double-sideband noise temperature of around 1000 K and a conversion gain of −3.5 dB were experimentally obtained at 20 K. At the temperature of 40 K, the measured mixer noise and conversion efficiency are around 2100 K and −10 dB, respectively. The experimental data are in good agreement with the numerical analysis results using the three-port model. A detailed performance comparison with other reported HTS terahertz mixers has confirmed the superior performance of our presented mixer device.

Applied Physics Letters•Nov 6, 2017•25 citations

Submicron-long HTS hot-electron mixers

Oliver Harnack, Boris S. Karasik, William R. McGrath +2 more

We have measured the device length and temperature dependence of the intermediate frequency (IF) bandwidth and noise of hot-electron bolometer (HEB) mixers made from a high- T c superconductor. Mixer devices with lengths (L) between 50 nm and 1 µm were fabricated from 25-35 nm thick YBCO films on MgO and sapphire substrates. Bandwidth measurements were made using signal and local oscillator (LO) frequencies in the range 1-20 GHz. At low operation temperatures the IF bandwidths were about 100 MHz and several hundred MHz for devices on MgO and sapphire, respectively. At higher operation temperatures, where self-heating disappeared and flux-flow effects define the shape of the I - V characteristic, the measured IF bandwidth increased significantly. The temperature and IF dependence of absolute conversion efficiencies determined from noise measurements are in good agreement with the bandwidth data. At 2.7 GHz LO frequency the single-side-band mixer noise temperature of a 50 nm long HEB on MgO was about 8000 K.

Superconductor Science and Technology•Nov 1, 1999•4 citations
The authors report on the mixing properties of high-temperature superconductor bicrystal Josephson junctions at 345 GHz and high-operating temperatures. A variable backshort and E-plane tuner enabled the control of impedance matching between the junction and the RF environment. The local oscillator frequency and intermediate frequency were 345 and 1.4 GHz, respectively. The double-side band (DSB) mixer noise temperature and the conversion efficiency were determined using the hot/cold method. The authors observed that the noise temperature was strongly dependent on the matching conditions. The lowest noise temperatures were observed for tuner positions supporting the formation of a subharmonic step which appeared between the zeroth and first Shapiro step. At T = 20 K they obtained a lowest DSB mixer noise temperature of 1003 K and a conversion efficiency of -1.2 dB. They have investigated the dependence of the noise temperature on the operating temperature in detail. The impact of resonances on the device performance will be discussed.
We report on experimental studies of the noise performance and conversion efficiency of high-Te Josephson mixers at frequencies between 90 GHz and 550 GHz. The heterodyne mixing experiments have been performed by using YBa2Cu307_8 step-edge junctions and bicrystal junctions on MgO (E--9.6) substrates. We studied the Josephson mixer performance for the case of internal pumping (selfpumping) and external pumping. Receiver noise measurements in a waveg,uide setup for the case of external pumping at 90-94 GHz gave formally calculated double-side-band (DSB) mixer noise temperatures (Tm) of about 2000 K at physical temperatures of 10 K. Similar measurements in a quasioptical setup at 4.2 K and at operation frequencies of 430 GHz and 546 GHz yielded mixer noise temperatures of 1200 K and 1100 K, respectively. Using the internal pumped mode, i.e. mixing without external local oscillator signal, we also obtained clear IF response in hot/cold-measurements. The formally calculated Tm were between 580 K and 2300 K.
A waveguide mixer based on a Josephson junction made from a high-temperature superconductor (HTS) has been analysed at frequencies of 90 GHz and 115 GHz. The mixer consisted of a single-grain-boundary bicrystal junction which was integrated with a bow-tie antenna and a microstrip filter structure fabricated on an MgO substrate. Two different designs of mixer block were tested. Using the first design the best noise performance was measured at a local oscillator (LO) frequency of about 90 GHz. At the projected LO frequency of 115 GHz significant deterioration of performance was observed. A computer simulation of the mixer chip and substrate channel structure was performed using the 3D simulation program HFSS. Sufficient RF signal rejection by the filter structure was confirmed at 90 GHz. After a simulation cycle at 115 GHz the substrate channel in the mixer block was modified. Using this second design we measured a double-sideband mixer noise temperature of 1090 K at 10 K operating temperature which is the best performance of an HTS Josephson mixer to date obtained at this frequency and temperature.
We have measured the noise performance and conversion efficiency of Y–Ba–Cu–O bicrystal Josephson mixers at operating temperatures between 20 and 60 K and at operating frequencies around 90 GHz. A double-sideband mixer noise temperature of about 1600 K and a conversion efficiency of −10 dB at 20 K operating temperature has been measured using the Y-factor method. The absorbed local oscillator power was in the range of 10 nW. The dependence of the mixer performance on the normalized frequency Ω and the fluctuation parameter Γ has been studied. In accordance with the resistively shunted junction model, the experimental data show the presence of excess noise. The temperature dependence of the mixer noise temperature can be explained by the variation of the linewidth of the Josephson oscillations with the operating temperature.
The authors have made a detailed study of the gain and noise of a SIS (superconductor-insulator-superconductor) heterodyne receiver at 345 GHz. An array of two Nb-Al/sub 2/O/sub 3/-Nb SIS junctions in series are used as the mixing element. The array is operated in a waveguide mount with a backshort and an E-plane tuner. The best receiver noise temperature achieved is 140 K DSB (double sideband). The embedding impedances were determined by fitting theory to the measured pumped curves. High-quality fits were obtained, providing the first detailed test of the Tucker-theory at frequencies above 300 GHz. The impedances found by this method are in very good agreement with impedances measured in a scale model at 3.3 GHz. From these embedding impedances, the gain and noise of the mixer were calculated over a full bias range using the Tucker theory in the three-port low-IF approximation. The measured dependence of mixer gain and noise on bias voltage, pump power and embedding impedance is in good agreement with theory. However the absolute values show discrepancies that appear to be independent of the bias parameters of the mixer.>
This letter presents both theoretical and experimental investigations on the noise and conversion performance of a high-Tc superconducting (HTS) step-edge Josephson-junction mixer at the frequency of 0.6 THz and operating temperatures of 20–40 K. Based on the Y-factor and U-factor methods, a double-sideband noise temperature of around 1000 K and a conversion gain of −3.5 dB were experimentally obtained at 20 K. At the temperature of 40 K, the measured mixer noise and conversion efficiency are around 2100 K and −10 dB, respectively. The experimental data are in good agreement with the numerical analysis results using the three-port model. A detailed performance comparison with other reported HTS terahertz mixers has confirmed the superior performance of our presented mixer device.
We have measured the device length and temperature dependence of the intermediate frequency (IF) bandwidth and noise of hot-electron bolometer (HEB) mixers made from a high- T c superconductor. Mixer devices with lengths (L) between 50 nm and 1 µm were fabricated from 25-35 nm thick YBCO films on MgO and sapphire substrates. Bandwidth measurements were made using signal and local oscillator (LO) frequencies in the range 1-20 GHz. At low operation temperatures the IF bandwidths were about 100 MHz and several hundred MHz for devices on MgO and sapphire, respectively. At higher operation temperatures, where self-heating disappeared and flux-flow effects define the shape of the I - V characteristic, the measured IF bandwidth increased significantly. The temperature and IF dependence of absolute conversion efficiencies determined from noise measurements are in good agreement with the bandwidth data. At 2.7 GHz LO frequency the single-side-band mixer noise temperature of a 50 nm long HEB on MgO was about 8000 K.