Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Experimental investigation of Cherenkov flux-flow oscillators

Vladislav V. Kurin, Alexey V. Yulin, E. Goldobin, Alexander M. Klushin, H. Kohlstedt, M. Levitchev, Norbert Thyssen

Published Jun 1, 1999• 5 citations
Publisher

Abstract

This paper is devoted to the experimental investigation of a new class of superconducting microwave oscillators based on Cherenkov radiation from Josephson vortices. Samples consisting of a long Josephson junction embedded in a dispersive transmission line with space-periodical inhomogeneities were fabricated and tested. We report observation of new resonances on the I-V curve of the system and present the first radiation measurements in the 80-120 GHz frequency range.

DOI
10.1109/77.783839

Related papers

Design and fabrication of Cherenkov flux-flow oscillator

Andrey M. Baryshev, Alexey V. Yulin, Vladislav V. Kurin +5 more

The Josephson Flux-Flow Oscillator (FFO) has been used as an on chip local oscillator at frequencies up to 650 GHz. The FFO linewidth of about 1 MHz was measured in the resonant regime V<915 /spl mu/V for niobium-aluminum oxide-niobium tunnel junctions, while considerably larger values were reported at higher voltages. To overcome this fundamental linewidth broadening we propose a novel on chip Cherenkov radiation flux-flow oscillator (CRFFO). It consists of a long Josephson junction and a superconducting slow wave transmission line that modifies essentially the junction dispersion relation. Two SIS detectors are connected both to the long Josephson junction and the transmission line to evaluate available microwave power. The output power coming both from the long junction and the transmission line is estimated at different bias conditions.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•8 citations

Forward and backward waves in Cherenkov flux-flow oscillators

Andrey M. Baryshev, Alexey V. Yulin, Vladislav V. Kurin +3 more

Josephson flux-flow oscillators (FFOs) have been used as an on-chip local oscillator at frequencies up to 650 GHz. An autonomous FFO linewidth of about 1 MHz was measured in the resonant regime at V b <950 µV for niobium-aluminium oxide-niobium tunnel junctions, while considerably larger values were reported at higher voltages. To overcome this fundamental linewidth broadening we propose an on-chip Cherenkov radiation flux-flow oscillator (CRFFO). It consists of a long Josephson junction and a superconducting slow-wave transmission line that modifies significantly the junction dispersion relation. Two superconductor-insulator-superconductor junction detectors are connected to both the long Josephson junction and the slow-wave line to determine the available microwave power. The power is measured at different CRFFO biasing conditions. Both a forward wave and a backward wave oscillation regime are observed. An FFO and a CRFFO with the same junction parameters are compared.

Superconductor Science and Technology•Nov 1, 1999•5 citations

Flux-flow-type Josephson oscillator consisting of epitaxial NbCN/MgO/NbCN junction

Shogo Kiryu, Satoshi Kohjiro, Alexandre Shoji +3 more

Flux-flow-type Josephson oscillators consisting of epitaxial NbCN/MgO/NbCN junctions were fabricated and their current-voltage (I-V) characteristics were measured in various magnetic fields to evaluate their oscillation characteristics. On the I-V curve for a fabricated oscillator, clear current steps were observed up to 3 mV, indicating that oscillation occurs up to 1.4 THz. Using a theoretical model, available output power for the oscillator was calculated to be in the range from 20 mu W to 40 mu W in the frequency range from 500 GHz to 1.2 THz.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•6 citations

Flux-flow-type Josephson oscillator for millimeter and submillimeter wave region. II. Modeling

Tadao Nagatsuma, Keiji Enpuku, Keiji Yoshida +1 more

A theoretical study is made of a travelling-wave-type oscillator, which utilizes a flux flow in a long Josephson junction for use as a local oscillator in the integrated superconducting receiver system. An internal electromagnetic field of the oscillator junction in the flux-flow state is investigated both numerically and analytically. It is shown that the voltage amplitude of the internal oscillation increases gradually in the direction of the flux flow and reaches a maximum value at the junction end. An equivalent circuit of the oscillator is also obtained, which gives dependences of the emitted radiation on frequency, magnetic field, and load. It is shown that the output power attains the value of the order of 10−6 W in the frequency range between 100 and 500 GHz, and that the output power and the radiation frequency can be controlled by both the bias voltage and the applied magnetic field. These theoretical results explain quantitatively the experimental ones with a Pb-alloy long junction of length 24 λJ.

Journal of Applied Physics•Dec 1, 1984•115 citations

Dynamics and Applications of Long Josephson Junctions

Yongming Zhang

The first object of this work is to theoretically study the effects of tunnel junction parameters on flux-flow Josephson oscillators (FFOs) by numerical simulation and to experimentally study the rf properties of FFOs by integrating them together with an SIS (superconductor-insulator-superconductor) mixer/detector on a chip. By using a CAD modeled integrated sub-mm wave receiver, the composite linewidth of two FFOs was measured to be less than 2.1 MHz in the band 280-330 GHz. The receiver consists of two identical FFOs and an SIS mixer. The linewidth was determined by mixing the two signals in the SIS mixer and analyzing the intermediate frequency. The output power coupled to a 10 .OMEGA. microstripline was about 0.5 µW, and could be adjusted by changing the current bias of the oscillator. The FFOs are connected to the SIS mixer via interdigital capacitors. The FFOs and the SIS element are made of Nb/NbOx/PbBi junctions by the "reactive ion beam oxidation" technique with the critical current density jc controlled by the oxidation time. Lift-off stencils for defining the junction sizes and the top-electrodes were made by using electron-beam writing on PMMA/Copolymer double layer resist. The jc of a long Josephson junction (LJJ) determines the fluxon motion. For LJJs which had jc > 1 kA/cm2, velocity-matching (VM, where the phase velocity of propagating fluxons equals that of the electromagnetic wave in the LJJ) steps could be tuned linearly from about 0.2 to 1.4 mV by an applied magnetic field. Coupled radiation at around 100 GHz (about 3 nW), 261 GHz (4.6 nW), and 330 GHz (0.43 µW), from flux-flow oscillations, was observed. From the step's steepness, the junction quality factor QJ is determined. QJ is between 4 to 7 in the voltage range of 0.4 to 1 mV. Coupled radiation (> 3 nW) at around 100 GHz corresponding to resonant soliton oscillation in low jc samples (250 to 1000 A/cm2) was detected. Simulations show that, for a uniform bias feed, the height of the VM step .gammam increases almost linearly with the external magnetic field .beta.e and the quasiparticle loss .alpha., but is less dependent on the surface loss .beta.. An approximate expression .gammam = a + .alpha(1+b).beta.e agrees with simulations. The maximum ac output voltage decreases with increasing dampings .alpha. and .beta.. It is important to include the .beta.-term in the mathematical model. The second part of this work is devoted to rf properties of long YBa2Cu3O7-.delta. (YBCO) grain boundary junctions made on 0- 32 °. [001]-tilt YSZ bicrystals. Josephson flux-flow resonances and Fiske resonances were observed. The first resonances could be tuned from about 0.5 to 2.0 mV in a 30 µm long junction at 16 K, and we determined the ratio between barrier thickness and relative dielectric constant td/.epsilon.r=2.9 Å and the loss .alpha.= 1.3 at 16 K. Simulations support the experimental observation that Josephson vortices can propagate unidirectionally in an overdamped, homogeneous junction up to .alpha.Ã? 2. From the Fiske resonances at 256-638 GHz, their Q-values, and the Steward-McCumber parameter, we find td/.epsilon.r=4 Å, the London penetration depth .gamma.L=145±5 nm and the surface resistance RS ~20 m.OMEGA. at 280 GHz. We conclude that the boundary is dielectric and the YBCO grains are well superconducting within 5-20 nm from the boundary. The dielectric between the grains could be part of a tunnel barrier and/or a matrix for filamentary conduction. Josephson flux-flow transitors based on long bicrystal junctions were made with an Au loop used as the control line. The line modulated the critical current Ic. Current gain larger than unity was obtained below 70 K. The gain increased with the junction length and varied roughly like the square root Ic when adjusting the temperature. A transresistance larger than 5 .OMEGA. was obtained at 15 K. Better performance is expected from junctions with high current densities.

•Jan 1, 1993•7 citations

Long Josephson junction embedded into a planar resonator at microwave frequencies: Numerical simulation of fluxon dynamics

E. Goldobin, Alexander M. Klushin, M. Siegel +1 more

We have investigated numerically a system consisting of a long Josephson junction embedded into a microstrip resonator. For such a configuration the Josephson vortex dynamics in the junction is driven by the oscillating currents in the resonator. We have calculated the complex impedance of the junction at the resonant frequency. The Q factor of the resonator and the change of the resonant frequency of the whole system can then be easily calculated knowing the parameters of the resonator without Josephson junction. The fluxon dynamics and the complex impedance of the junction are simulated for different values of the junction length, damping, dc bias current, and dc magnetic field. This allows us to explain the behavior of the impedance of the junction and different loss mechanisms. In particular, we predict a nonmonotonic dependence of the both real and imaginary parts of the impedance on the amplitude of the oscillating current in the resonator for some range of parameters. Our results show that such a combination of active and passive superconducting elements forms a rather interesting nonlinear physical system which might be useful for development of tunable/switchable superconducting resonators and suggests an experimental technique for detecting trapped vortices in long junctions.

Journal of Applied Physics•Aug 30, 2002•7 citations
This paper is devoted to the experimental investigation of a new class of superconducting microwave oscillators based on Cherenkov radiation from Josephson vortices. Samples consisting of a long Josephson junction embedded in a dispersive transmission line with space-periodical inhomogeneities were fabricated and tested. We report observation of new resonances on the I-V curve of the system and present the first radiation measurements in the 80-120 GHz frequency range.
The Josephson Flux-Flow Oscillator (FFO) has been used as an on chip local oscillator at frequencies up to 650 GHz. The FFO linewidth of about 1 MHz was measured in the resonant regime V<915 /spl mu/V for niobium-aluminum oxide-niobium tunnel junctions, while considerably larger values were reported at higher voltages. To overcome this fundamental linewidth broadening we propose a novel on chip Cherenkov radiation flux-flow oscillator (CRFFO). It consists of a long Josephson junction and a superconducting slow wave transmission line that modifies essentially the junction dispersion relation. Two SIS detectors are connected both to the long Josephson junction and the transmission line to evaluate available microwave power. The output power coming both from the long junction and the transmission line is estimated at different bias conditions.
Josephson flux-flow oscillators (FFOs) have been used as an on-chip local oscillator at frequencies up to 650 GHz. An autonomous FFO linewidth of about 1 MHz was measured in the resonant regime at V b <950 µV for niobium-aluminium oxide-niobium tunnel junctions, while considerably larger values were reported at higher voltages. To overcome this fundamental linewidth broadening we propose an on-chip Cherenkov radiation flux-flow oscillator (CRFFO). It consists of a long Josephson junction and a superconducting slow-wave transmission line that modifies significantly the junction dispersion relation. Two superconductor-insulator-superconductor junction detectors are connected to both the long Josephson junction and the slow-wave line to determine the available microwave power. The power is measured at different CRFFO biasing conditions. Both a forward wave and a backward wave oscillation regime are observed. An FFO and a CRFFO with the same junction parameters are compared.
Flux-flow-type Josephson oscillators consisting of epitaxial NbCN/MgO/NbCN junctions were fabricated and their current-voltage (I-V) characteristics were measured in various magnetic fields to evaluate their oscillation characteristics. On the I-V curve for a fabricated oscillator, clear current steps were observed up to 3 mV, indicating that oscillation occurs up to 1.4 THz. Using a theoretical model, available output power for the oscillator was calculated to be in the range from 20 mu W to 40 mu W in the frequency range from 500 GHz to 1.2 THz.>
A theoretical study is made of a travelling-wave-type oscillator, which utilizes a flux flow in a long Josephson junction for use as a local oscillator in the integrated superconducting receiver system. An internal electromagnetic field of the oscillator junction in the flux-flow state is investigated both numerically and analytically. It is shown that the voltage amplitude of the internal oscillation increases gradually in the direction of the flux flow and reaches a maximum value at the junction end. An equivalent circuit of the oscillator is also obtained, which gives dependences of the emitted radiation on frequency, magnetic field, and load. It is shown that the output power attains the value of the order of 10−6 W in the frequency range between 100 and 500 GHz, and that the output power and the radiation frequency can be controlled by both the bias voltage and the applied magnetic field. These theoretical results explain quantitatively the experimental ones with a Pb-alloy long junction of length 24 λJ.
The first object of this work is to theoretically study the effects of tunnel junction parameters on flux-flow Josephson oscillators (FFOs) by numerical simulation and to experimentally study the rf properties of FFOs by integrating them together with an SIS (superconductor-insulator-superconductor) mixer/detector on a chip. By using a CAD modeled integrated sub-mm wave receiver, the composite linewidth of two FFOs was measured to be less than 2.1 MHz in the band 280-330 GHz. The receiver consists of two identical FFOs and an SIS mixer. The linewidth was determined by mixing the two signals in the SIS mixer and analyzing the intermediate frequency. The output power coupled to a 10 .OMEGA. microstripline was about 0.5 µW, and could be adjusted by changing the current bias of the oscillator. The FFOs are connected to the SIS mixer via interdigital capacitors. The FFOs and the SIS element are made of Nb/NbOx/PbBi junctions by the "reactive ion beam oxidation" technique with the critical current density jc controlled by the oxidation time. Lift-off stencils for defining the junction sizes and the top-electrodes were made by using electron-beam writing on PMMA/Copolymer double layer resist. The jc of a long Josephson junction (LJJ) determines the fluxon motion. For LJJs which had jc > 1 kA/cm2, velocity-matching (VM, where the phase velocity of propagating fluxons equals that of the electromagnetic wave in the LJJ) steps could be tuned linearly from about 0.2 to 1.4 mV by an applied magnetic field. Coupled radiation at around 100 GHz (about 3 nW), 261 GHz (4.6 nW), and 330 GHz (0.43 µW), from flux-flow oscillations, was observed. From the step's steepness, the junction quality factor QJ is determined. QJ is between 4 to 7 in the voltage range of 0.4 to 1 mV. Coupled radiation (> 3 nW) at around 100 GHz corresponding to resonant soliton oscillation in low jc samples (250 to 1000 A/cm2) was detected. Simulations show that, for a uniform bias feed, the height of the VM step .gammam increases almost linearly with the external magnetic field .beta.e and the quasiparticle loss .alpha., but is less dependent on the surface loss .beta.. An approximate expression .gammam = a + .alpha(1+b).beta.e agrees with simulations. The maximum ac output voltage decreases with increasing dampings .alpha. and .beta.. It is important to include the .beta.-term in the mathematical model. The second part of this work is devoted to rf properties of long YBa2Cu3O7-.delta. (YBCO) grain boundary junctions made on 0- 32 °. [001]-tilt YSZ bicrystals. Josephson flux-flow resonances and Fiske resonances were observed. The first resonances could be tuned from about 0.5 to 2.0 mV in a 30 µm long junction at 16 K, and we determined the ratio between barrier thickness and relative dielectric constant td/.epsilon.r=2.9 Å and the loss .alpha.= 1.3 at 16 K. Simulations support the experimental observation that Josephson vortices can propagate unidirectionally in an overdamped, homogeneous junction up to .alpha.Ã? 2. From the Fiske resonances at 256-638 GHz, their Q-values, and the Steward-McCumber parameter, we find td/.epsilon.r=4 Å, the London penetration depth .gamma.L=145±5 nm and the surface resistance RS ~20 m.OMEGA. at 280 GHz. We conclude that the boundary is dielectric and the YBCO grains are well superconducting within 5-20 nm from the boundary. The dielectric between the grains could be part of a tunnel barrier and/or a matrix for filamentary conduction. Josephson flux-flow transitors based on long bicrystal junctions were made with an Au loop used as the control line. The line modulated the critical current Ic. Current gain larger than unity was obtained below 70 K. The gain increased with the junction length and varied roughly like the square root Ic when adjusting the temperature. A transresistance larger than 5 .OMEGA. was obtained at 15 K. Better performance is expected from junctions with high current densities.
We have investigated numerically a system consisting of a long Josephson junction embedded into a microstrip resonator. For such a configuration the Josephson vortex dynamics in the junction is driven by the oscillating currents in the resonator. We have calculated the complex impedance of the junction at the resonant frequency. The Q factor of the resonator and the change of the resonant frequency of the whole system can then be easily calculated knowing the parameters of the resonator without Josephson junction. The fluxon dynamics and the complex impedance of the junction are simulated for different values of the junction length, damping, dc bias current, and dc magnetic field. This allows us to explain the behavior of the impedance of the junction and different loss mechanisms. In particular, we predict a nonmonotonic dependence of the both real and imaginary parts of the impedance on the amplitude of the oscillating current in the resonator for some range of parameters. Our results show that such a combination of active and passive superconducting elements forms a rather interesting nonlinear physical system which might be useful for development of tunable/switchable superconducting resonators and suggests an experimental technique for detecting trapped vortices in long junctions.