Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

SNS programmable voltage standard

C.A. Hamilton, Samuel P. Benz, Charles J. Burroughs, Todd E. Harvey

Published Jun 1, 1997• 26 citations
Publisher

Abstract

Superconductor-Normal-Superconductor (SNS) junctions have been used in the design and fabrication of a 1-V rapidly programmable voltage standard. The superconducting circuit is a series array of 32 768 Nb-PdAu-Nb junctions with taps that divide the array into a binary sequence of smaller array segments with a minimum segment size of 128 junctions. The 16-GHz drive frequency is set by the characteristic frequency of the junctions. A computer-controlled 8-channel bias system controls the current in each segment and allows the rapid selection of any one of 513 discrete voltage levels. The system is designed for fast dc measurements and the synthesis of precise ac waveforms.

DOI
10.1109/77.621740

Related papers

Superconductor-normal-superconductor junctions for programmable voltage standards

S. P. Benz

Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.

Applied Physics Letters•Oct 30, 1995•133 citations

SNS junction on Nb-Ti base for microwave circuits

M. Schubert, Ludwig Fritzsch, G. Wende +1 more

Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•12 citations

Stacked SNS Josephson junction arrays for quantum voltage standards

Paul D. Dresselhaus, Yonuk Chong, J. H. Plantenberg +1 more

NIST is using and developing superconductor-normal metal-superconductor (SNS) Josephson arrays for both programmable DC and AC voltage standards. Increasing the output voltage is difficult because the output voltage per junction is small; hence series arrays with large numbers of junctions are needed. The best way to generate higher voltages and achieve the best operating margins for the broadband drive signals is by densely packing the junctions into shorter arrays. NIST has been working on stacked SNS junctions to achieve this goal. By stacking junctions in the array, more junctions may be placed per length, while preserving a lumped microwave element. In this paper we introduce our results on stacked SNS junctions using MoSi/sub 2/ and Ti as barrier materials. These barriers were chosen because they can be reactive-ion etched (RIE) in contrast to our standard PdAu barriers, which must be wet etched. Using RIE, alternating layers of barrier material and Nb may be etched in a single step. We indirectly quantify the junction uniformity in the arrays by measuring the current range of the constant-voltage steps when the arrays are biased with a microwave drive.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•36 citations

Development and Investigation of SNS Josephson Arrays for the Josephson Arbitrary Waveform Synthesizer

J. Kohlmann, Oliver Kieler, Ricardo Iuzzolino +4 more

Superconductor-normal metal-superconductor(SNS) Josephson junction series arrays are developed and investigated for applications in the Josephson arbitrary waveform synthesizer (JAWS). The series arrays contain up to about 10 000 junctions arranged in a meanderlike design. AC voltages and arbitrary waveforms are synthesized by operation of the Josephson junctions by short current pulses. Higher harmonics are at least 110 dB below the fundamental. To verify the generated waveforms, a spectrum analyzer that has initially been calibrated using a binary-divided programmable Josephson voltage standard is used.

IEEE Transactions on Instrumentation and Measurement•Dec 3, 2008•26 citations

Improved design of superconductor/normal conductor/superconductor Josephson junction series arrays for an ac Josephson voltage standard

Oliver Kieler, J. Kohlmann, Franz Müller

Superconductor/normal conductor/superconductor (SNS) Josephson junction series arrays are the subject of research for the realization of a Josephson arbitrary waveform synthesizer (JAWS) based on pulse-driven Josephson junctions. Lumped arrays of SNS Josephson junctions are investigated for this application at the Physikalisch-Technische Bundesanstalt (PTB). The series arrays consisting of Nb/HfTi/Nb SNS junctions are embedded in the center line of a coplanar waveguide transmission line. To increase the ac output voltage, the Josephson junction series array is designed as a meander-like structure. A broadband response of the arrays is required for the complex pulse operation of the JAWS. The arrays are investigated by dc measurements and for test purposes under continuous microwave irradiation at different frequencies. Flat Shapiro steps were measured for meander-like series arrays with 21 parallel lines containing up to 10 752 junctions. A sine wave with a frequency of 2.5 kHz and a peak voltage of 214 mV Peak was synthesized under pulse mode operation.

Superconductor Science and Technology•Oct 18, 2007•28 citations

Josephson Series Arrays for Programmable 10-V SINIS Josephson Voltage Standards and for Josephson Arbitrary Waveform Synthesizers Based on SNS Junctions

J. Kohlmann, F. Muller, Oliver Kieler +4 more

Programmable Josephson voltage standards for output voltages up to 10 V have been realized. Binary-divided series arrays consisting of 69 632 overdamped SINIS Josephson junctions have been fabricated using reliable Nb-Al/Al2O3technology (S: superconductor, I: insulator, N: normal metal). Series arrays of about 1000 SNS Josephson junctions were realized as lumped arrays for applications in the Josephson arbitrary waveform synthesizer (JAWS). We suggest a novel scheme for combining the higher voltages generated by the binary-divided arrays with the frequency spectral characteristics of the JAWS, in order to optimize the frequency spectrum of the generated ac voltages

IEEE Transactions on Instrumentation and Measurement•Mar 16, 2007•32 citations
Superconductor-Normal-Superconductor (SNS) junctions have been used in the design and fabrication of a 1-V rapidly programmable voltage standard. The superconducting circuit is a series array of 32 768 Nb-PdAu-Nb junctions with taps that divide the array into a binary sequence of smaller array segments with a minimum segment size of 128 junctions. The 16-GHz drive frequency is set by the characteristic frequency of the junctions. A computer-controlled 8-channel bias system controls the current in each segment and allows the rapid selection of any one of 513 discrete voltage levels. The system is designed for fast dc measurements and the synthesis of precise ac waveforms.
Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.
Superconductor-normal metal-superconductor (SNS) junctions are well-suited for large-scale integrated superconducting circuits. Potential applications are programmable voltage standards, digital-to-analog converters and large-scale RSFQ circuits. The application of SNS junctions provides some advantages, e.g. a simplified fabrication technology and reduced parasitic inductances. But it requires a technological process with dimensions down to the submicrometer region to achieve sufficiently high characteristic voltages I/sub C/R/sub N/. In our process the normal metal interlayer is titanium. Therefore the sidewall insulation of the junctions can be made by anodization, as it is known from the Nb-Al technology. Nb-Ti-Nb Josephson junctions and junction arrays were fabricated down to the submicrometer range with I/sub C/R/sub N/ values up to 87 microvolt depending on the titanium thickness. Their measured critical currents have a small spread of about 10 percent. Shapiro steps are observed under the influence of microwave irradiation. For the application of such junctions in a programmable Josephson voltage standard a new type of microwave circuit using coplanar strips is proposed and successfully tested in 10 V SIS circuits.
NIST is using and developing superconductor-normal metal-superconductor (SNS) Josephson arrays for both programmable DC and AC voltage standards. Increasing the output voltage is difficult because the output voltage per junction is small; hence series arrays with large numbers of junctions are needed. The best way to generate higher voltages and achieve the best operating margins for the broadband drive signals is by densely packing the junctions into shorter arrays. NIST has been working on stacked SNS junctions to achieve this goal. By stacking junctions in the array, more junctions may be placed per length, while preserving a lumped microwave element. In this paper we introduce our results on stacked SNS junctions using MoSi/sub 2/ and Ti as barrier materials. These barriers were chosen because they can be reactive-ion etched (RIE) in contrast to our standard PdAu barriers, which must be wet etched. Using RIE, alternating layers of barrier material and Nb may be etched in a single step. We indirectly quantify the junction uniformity in the arrays by measuring the current range of the constant-voltage steps when the arrays are biased with a microwave drive.
Superconductor-normal metal-superconductor(SNS) Josephson junction series arrays are developed and investigated for applications in the Josephson arbitrary waveform synthesizer (JAWS). The series arrays contain up to about 10 000 junctions arranged in a meanderlike design. AC voltages and arbitrary waveforms are synthesized by operation of the Josephson junctions by short current pulses. Higher harmonics are at least 110 dB below the fundamental. To verify the generated waveforms, a spectrum analyzer that has initially been calibrated using a binary-divided programmable Josephson voltage standard is used.
Superconductor/normal conductor/superconductor (SNS) Josephson junction series arrays are the subject of research for the realization of a Josephson arbitrary waveform synthesizer (JAWS) based on pulse-driven Josephson junctions. Lumped arrays of SNS Josephson junctions are investigated for this application at the Physikalisch-Technische Bundesanstalt (PTB). The series arrays consisting of Nb/HfTi/Nb SNS junctions are embedded in the center line of a coplanar waveguide transmission line. To increase the ac output voltage, the Josephson junction series array is designed as a meander-like structure. A broadband response of the arrays is required for the complex pulse operation of the JAWS. The arrays are investigated by dc measurements and for test purposes under continuous microwave irradiation at different frequencies. Flat Shapiro steps were measured for meander-like series arrays with 21 parallel lines containing up to 10 752 junctions. A sine wave with a frequency of 2.5 kHz and a peak voltage of 214 mV Peak was synthesized under pulse mode operation.
Programmable Josephson voltage standards for output voltages up to 10 V have been realized. Binary-divided series arrays consisting of 69 632 overdamped SINIS Josephson junctions have been fabricated using reliable Nb-Al/Al2O3technology (S: superconductor, I: insulator, N: normal metal). Series arrays of about 1000 SNS Josephson junctions were realized as lumped arrays for applications in the Josephson arbitrary waveform synthesizer (JAWS). We suggest a novel scheme for combining the higher voltages generated by the binary-divided arrays with the frequency spectral characteristics of the JAWS, in order to optimize the frequency spectrum of the generated ac voltages