Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Strongly coupled, low noise dc-SQUID amplifiers

J. Pleikies

Published Apr 1, 2009• 0 citations
Publisher

Abstract

The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.

DOI
10.3990/1.9789036528320

Related papers

Optimization of a Low-Tc DC SQUID Amplifier With Tightly Coupled Input Coils

J. Pleikies, O. Usenko, G. Frossati +1 more

We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•6 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations

Development of Low-Noise Two-stage dc-SQUID for TES Detector Readout

Nan Li, Mengjie Song, Sixiao Hu +9 more

Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22-48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer (TDM) SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array (SSA) with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at $300$ $mK$ in an adiabatic demagnetisation refrigerator (ADR). The the measured magnetic flux noise of the two-stage SQUID circuit system is approximately $0.3$ $μΦ_{0}/\sqrt{Hz}$ at $10$ $kHz$. The current noise equivalent to the input coil of input SQUID is about $2.4$ $pA/\sqrt{Hz}$. This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.

arXiv:2601.19565•Jan 27, 2026•0 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation

Development of low-noise two-stage dc-SQUID for TES detector readout

Nan Li, Mengjie Song, Sixiao Hu +9 more

Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.

Superconductor Science and Technology•Apr 1, 2026•0 citations

Sensitivity enhancement of Quantum Design dc superconducting quantum interference devices in two-stage configuration

R. Mezzena, Andrea Vinante, P. Falferi +5 more

The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.

Review of Scientific Instruments•Sep 1, 2001•31 citations
The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.
We optimized the design and operation of a low-Tc direct current superconducting quantum interference device (dc SQUID) with an integrated coupling coil of 1.5 muH inductance taking into account typical effects observed for similar devices. Numerical simulations were performed on a model including the capacitance of the Josephson junctions, thermal noise of the integrated shunt- and damping- resistors as well as a complex frequency dependent impedance of the SQUID loop originating from the integrated coils. The experimentally and numerically determined characteristics and sensitivity are in good agreement. A minimum additional coupled energy resolution of 700 (h/2p) and 250 (h/2p) was measured at a temperature of 4.2 K and 1.5 K, respectively.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22-48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer (TDM) SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array (SSA) with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300300300 mKmKmK in an adiabatic demagnetisation refrigerator (ADR). The the measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.30.30.3 μΦ0/HzμΦ_{0}/\sqrt{Hz}μΦ0​/Hz​ at 101010 kHzkHzkHz. The current noise equivalent to the input coil of input SQUID is about 2.42.42.4 pA/HzpA/\sqrt{Hz}pA/Hz​. This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.
The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.