Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Dynamic performance of single-stage SQUID current amplifier with varying device parameters

Jin‐Mok Kim, Yong‐Ho Lee, Hyukchan Kwon, Yang-Sup Song

Published Jun 1, 2003• 0 citations
Publisher

Abstract

We have fabricated a single-stage superconducting quantum interference device (SQUID) current amplifier for detecting pulse outputs of a superconducting microcalorimeter. The current amplifier is made of a double relaxation oscillation SQUID (DROS) that provides a high flux-to-voltage transfer of about 1mV//spl Phi//sub 0/ and a large modulation depth of 80 /spl mu/V. Due to the high flux-to-voltage transfer, the voltage output of the DROS is measured directly with a room-temperature dc preamplifier. The bandwidth of the current amplifier is measured to be 1.2 MHz. Typical noise of the DROS current amplifier is about 6 pA//spl radic/Hz.

DOI
10.1109/tasc.2003.814042

Related papers

Two-stage amplifier based on a double relaxation oscillation superconducting quantum interference device

M. Podt, Michiel J. van Duuren, A.W. Hamster +2 more

A low-noise single-chip two-stage superconducting quantum interference device (SQUID) system with a double relaxation oscillation SQUID as the second stage has been realized. The system was operated in a direct voltage readout mode, with a closed loop bandwidth up to 1 MHz. Operated at 4.2 K, the white flux noise measured in flux locked loop was 1.3 μΦ0/√Hz, corresponding to an energy sensitivity of ε≈27h. Owing to the large flux-to-voltage transfer of up to 3.6 mV/Φ0, the room-temperature preamplifier noise did not dominate the overall flux noise.

Applied Physics Letters•Oct 11, 1999•25 citations

Broadband SQUID amplifiers for photonic applications

Vladimir Polushkin, D. Glowacka, R. Hart +1 more

The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•1 citation

Low-noise SQUIDs with large transfer - two stage SQUIDs based on DROSs

M. Podt, Jakob Flokstra, Horst Rogalla

We have realized a two-stage integrated superconducting quantum interference device (SQUID) system with a closed loop bandwidth of 2.5 MHz, operated in a direct voltage readout mode. The corresponding flux slew rate was 1.3×105 Φ0/s and the measured white flux noise was 1.3 μΦ0/√Hz at 4.2 K. The system is based on a conventional dc SQUID with a double relaxation oscillation SQUID (DROS) as the second stage. Because of the large flux-to-voltage transfer, the sensitivity of the system is completely determined by the sensor SQUID and not by the DROS or the room-temperature preamplifier. Decreasing the Josephson junction area enables a further improvement of the sensitivity of the two-stage SQUID systems.

•Aug 26, 2001•0 citations

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•72 citations

A low-noise, two-stage DC SQUID amplifier with high bandwidth and dynamic range

R. Cantor, L. P. Lee, Andrei N. Matlashov +1 more

We describe a low-noise, two-stage dc Superconducting QUantum Interference Device (SQUID) amplifier that is designed for applications requiring high bandwidth and dynamic range. The output signal of a low-noise SQUID in the input stage coherently modulates a series array of identical SQUIDs in the output stage via a common modulation line. The input stage is designed so its output signal does not produce multiple modulation periods in the output stage. The output stage is designed to have sufficient gain so the output noise is dominated by the amplified noise of the input SQUID and exceeds the noise of a preamplifier in the room temperature readout electronics. The SQUID amplifier may therefore be operated without flux modulation or any impedance matching network, resulting in a large dynamic range and high bandwidth.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•11 citations

1 pA/$\sqrt{\text{Hz}}$ Amplifier Using Superconducting Quantum Interference Device Array

T. Morooka, Hiroaki Myoren, S. Takada +1 more

An ultrahigh current resolution of 1 pA/√Hz was achieved by a superconducting quantum interference device (SQUID) amplifier, which consisted of 128 repeated dc-SQUID elements. Each element had a 7-turn input coil. The SQUID amplifier was fabricated using a Nb/AlO x /Nb fabrication process. To evaluate current resolution, flux noise and flux-voltage (Φ- V ) characteristics were measured at 4.2 K. The Φ- V characteristics showed a large voltage swing of more than 4 mV. The SQUID amplifier was operated at a smooth slope in the Φ- V characteristics, while asymmetric behavior appeared in the same Φ- V characteristics.

Japanese Journal of Applied Physics•Nov 1, 2003•1 citation
We have fabricated a single-stage superconducting quantum interference device (SQUID) current amplifier for detecting pulse outputs of a superconducting microcalorimeter. The current amplifier is made of a double relaxation oscillation SQUID (DROS) that provides a high flux-to-voltage transfer of about 1mV//spl Phi//sub 0/ and a large modulation depth of 80 /spl mu/V. Due to the high flux-to-voltage transfer, the voltage output of the DROS is measured directly with a room-temperature dc preamplifier. The bandwidth of the current amplifier is measured to be 1.2 MHz. Typical noise of the DROS current amplifier is about 6 pA//spl radic/Hz.
A low-noise single-chip two-stage superconducting quantum interference device (SQUID) system with a double relaxation oscillation SQUID as the second stage has been realized. The system was operated in a direct voltage readout mode, with a closed loop bandwidth up to 1 MHz. Operated at 4.2 K, the white flux noise measured in flux locked loop was 1.3 μΦ0/√Hz, corresponding to an energy sensitivity of ε≈27h. Owing to the large flux-to-voltage transfer of up to 3.6 mV/Φ0, the room-temperature preamplifier noise did not dominate the overall flux noise.
The dynamics and noise of a dc SQUID (the Superconducting Quantum Interference Device), with the McCumber parameter /spl beta//sub c/=2/spl pi/R/sup 2/l/sub c/C//spl Phi//sub 0/ close to the unity (where I/sub c/, R, C is the critical current, the shunt resistance and the capacitance of the Josephson junctions comprising the SQUID, respectively, /spl Phi//sub 0/=2.07 10/sup -15/ Wb is the magnetic flux quantum) integrated with a planar spiral input coil, have been experimentally studied. The length of the spiral input coil was chosen so as to match its /spl lambda//4 microwave resonance frequency to the plasma resonance frequency of the SQUID. The input coil resonance is found to enhance the overall quality factor Q of the Josephson oscillations in the SQUID and, as a result, to increase the dynamic resistance R/sub d/ and the gradient of the flux-to-voltage characteristics, /spl delta/V//spl delta//spl Phi/, without hysteresis. A dc SQUID with a loop inductance L=30.5 pH, /spl beta//sub c/=0.72, and a 6 turn input coil demonstrated a non-distorted quasi-sinusoidal flux-to-voltage transfer function with an exceptionally large modulation depth of 140 /spl mu/V peak-to-peak. The spectral density of the magnetic flux noise was as low as 3.5/spl times/10/sup -7/ /spl Phi//sub 0//Hz/sup 1/2/ in the double stage configuration, measured at a temperature 4.2 K using direct read out electronics. In combination with an intermediary transformer, the current resolution of the SQUID is as low as 1.25 pA/Hz/sup 1/2/ with an input coil inductance of 100 nH.
We have realized a two-stage integrated superconducting quantum interference device (SQUID) system with a closed loop bandwidth of 2.5 MHz, operated in a direct voltage readout mode. The corresponding flux slew rate was 1.3×105 Φ0/s and the measured white flux noise was 1.3 μΦ0/√Hz at 4.2 K. The system is based on a conventional dc SQUID with a double relaxation oscillation SQUID (DROS) as the second stage. Because of the large flux-to-voltage transfer, the sensitivity of the system is completely determined by the sensor SQUID and not by the DROS or the room-temperature preamplifier. Decreasing the Josephson junction area enables a further improvement of the sensitivity of the two-stage SQUID systems.
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
We describe a low-noise, two-stage dc Superconducting QUantum Interference Device (SQUID) amplifier that is designed for applications requiring high bandwidth and dynamic range. The output signal of a low-noise SQUID in the input stage coherently modulates a series array of identical SQUIDs in the output stage via a common modulation line. The input stage is designed so its output signal does not produce multiple modulation periods in the output stage. The output stage is designed to have sufficient gain so the output noise is dominated by the amplified noise of the input SQUID and exceeds the noise of a preamplifier in the room temperature readout electronics. The SQUID amplifier may therefore be operated without flux modulation or any impedance matching network, resulting in a large dynamic range and high bandwidth.
1 pA/Hz\sqrt{\text{Hz}}Hz​ Amplifier Using Superconducting Quantum Interference Device Array
An ultrahigh current resolution of 1 pA/√Hz was achieved by a superconducting quantum interference device (SQUID) amplifier, which consisted of 128 repeated dc-SQUID elements. Each element had a 7-turn input coil. The SQUID amplifier was fabricated using a Nb/AlO x /Nb fabrication process. To evaluate current resolution, flux noise and flux-voltage (Φ- V ) characteristics were measured at 4.2 K. The Φ- V characteristics showed a large voltage swing of more than 4 mV. The SQUID amplifier was operated at a smooth slope in the Φ- V characteristics, while asymmetric behavior appeared in the same Φ- V characteristics.