Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)

Study of a bright, slow, and cold cesium source for a continuous beam frequency standard

P. Berthoud, E. Fretel, P. Thomann

Published Jan 22, 2003• 2 citations
Publisher

Abstract

To achieve a primary frequency standard based on a continuous fountain of laser cooled cesium atoms, we report on the production of a bright, slow and cold continuous atomic beam. Atoms are cooled from a thermal vapor in a 45/spl deg/ laser geometry and launched directly from the optical molasses by the moving molasses technique. The effects of the source fluorescence on the continuous beam (average velocity, temperature and flux) have been observed, and ways to optimize simultaneously the atomic capture and the continuous beam are presented. Flux measurements rise to 2/spl times/10/sup 8/ at/s from a 2D magneto-optical trap at 7 m/s. The initial velocity is easily tunable from 1 to 10 m/s. If the longitudinal temperature is about 70 /spl mu/K, additional transverse cooling even reduces the transverse temperature in one dimension below 30 /spl mu/K. By extrapolating the obtained atomic flux to the continuous fountain under construction, we expect a short-term stability of 7/spl times/10/sup -14//spl tau//sup -1/2/. Other applications of continuous beams of cold atoms are suggested.

DOI
10.1109/freq.1999.840714

Related papers

Bright, slow, and continuous beam of laser-cooled cesium atoms

P. Berthoud, E. Fretel, P. Thomann

By the moving molasses technique we have extracted laser-cooled cesium atoms in a continuous way directly from an optical molasses. The mean launching velocity is precisely tunable from 1 to 12 m/s. The atomic beam has a flux of $1.3\ifmmode\times\else\texttimes\fi{}{10}^{8} \mathrm{a}\mathrm{t}\mathrm{o}\mathrm{m}/\mathrm{s}$ at 7 m/s and a longitudinal temperature of $70 \ensuremath{\mu}\mathrm{K},$ which represents the highest flux and lowest velocity spread obtained so far in a continuous beam of cold atoms. These features makes it well suited for atomic fountains. The atomic flux can be slightly increased in a two-dimensional magneto-optical trap operation $(+40%).$ A simple model accounts for the observed dependence of the flux with the magnetic-field gradient.

Physical Review A•Dec 1, 1999•41 citations

Low velocity, high flux, continuous source of cesium atoms

N. Castagna, Jocelyne Guéna, Mark D. Plimmer +1 more

We present a 2D magneto-optical trap (MOT) that uses an innovative simple optical configuration. Instead of mirrors and quarter-wave plates we use metal-coated retro-reflecting prisms so as to recycle the optical power of the cooling laser beam. We have characterised this source for three different configurations: with and without transverse magnetic field gradient, as well as with a pusher beam to produce a 2D+-MOT. The longitudinal velocity is about 25 m·s-1, with a transverse velocity spread ≤ 1 m·s-1, while the typical atomic flux density can be as much as 1.3×1014 at·s-1·m-2 for a cesium vapour pressure of ~4×10-8 mbar in the source. We use this low velocity atomic beam, instead of thermal vapour, to load a 3D moving optical molasses that launches a continuous cold cesium fountain. We achieve a gain of a factor ~ 20 in the fountain's atomic flux.

European Frequency and Time Forum•Mar 27, 2006•1 citation

A novel simplified two-dimensional magneto-optical trap as an intense source of slow cesium atoms

N. Castagna, Jocelyne Guéna, Mark D. Plimmer +1 more

We describe the design and performance of a slow atom source based on a 2D magneto-optical trap (MOT) that uses an innovative simple optical configuration. Metal-coated retro-reflecting prisms replace mirrors and quarter-wave plates so the optical power of the cooling laser beam is recycled. This source has been characterised for three different configurations: with and without transverse magnetic field gradient, and with a pusher beam to obtain a 2D+-MOT. The longitudinal velocity is of the order of 25 m·s−1, with a transverse velocity spread ≤1 m·s−1, while the typical atomic flux density obtained is up to 1.3×1014 at ·s−1·m−2 for a cesium vapour pressure of ~4×10−8 mbar in the source. We use this slow atom beam, instead of cesium vapour, to load a 3D moving optical molasses that feeds a continuous cold atom fountain. We obtain a gain of a factor ~20 in the atomic flux launched by the fountain.

The European Physical Journal Applied Physics•Apr 1, 2006•23 citations

CW fountain of laser-cooled Yb atoms

Ketan D. Rathod, Alok K. Singh, Vasant Natarajan A

We demonstrate launching of laser-cooled Yb atoms in a continuous atomic beam. The continuous cold beam has significant advantages over the more-common pulsed fountain, which was also demonstrated by us recently. The cold beam is formed in the following steps---(i) Atoms from a thermal beam are first Zeeman slowed to a small final velocity, (ii) the slowed atoms are captured in a two-dimensional magneto-optic trap (2D-MOT), and (iii) atoms are launched {\em continuously} in the vertical direction using two sets of moving-molasses beams, inclined at $\pm 15^\circ$ to the vertical. The cooling transition used is the strongly-allowed ${^1S}_0 \rightarrow {^1P}_1$ transition at 399 nm. We capture about $7 \times 10^6$ atoms in the 2D-MOT, and then launch them with a vertical velocity of 13 m/s at a longitudinal temperature of 125(6) mK.

•Mar 28, 2013•0 citations

An intense, highly collimated continuous Cesium fountain

N. Castagna

The realisation of cold and slow atomic beams has opened the way to a series of precision measurements of high scientific interest, as atom interferometry, Bose-Einstein Condensation and atomic fountain clocks. The latter are used since several years as reference clocks, given the high performance that they can reach both in accuracy and stability. The common philosophy in the construction of atomic fountains has been the pulsed technique, where an atoms sample is launched vertically and then falls down under the effect of the gravity. The Observatoire de Neuchâtel had a different approach and has built a fountain clock (FOCS1) operating in a continuous mode. This technique offers two main advantages: the diminution of the undesirable effects due to the atomic density (e.g. collisions between the atoms and cavity pulling) and to the noise of the local oscillator (intermodulation effect). To take full advantage of the continuous fountain approach however, we need to increase the atomic flux. The techniques chosen to reach this goal are an efficient transverse collimation together with more atoms to begin with. Here we report on a study of different transverse collimation techniques performed in a two-dimensional phase stable optical lattice (namely gray molasses and magnetically induced laser cooling) as well as the development and characterisation of a 2D-magneto-optical trap used to load the fountain. Best performances are reached in a 2D+-MOT configuration of such a pre-source, for which we detect an atomic flux 20 times greater than the one measured when the fountain is loaded by a Cs vapour. This gain could improve the atomic clock stability by a factor 6. An even better stability is expected after introducing a pre-cooling stage before performing the transverse collimation. This new configuration is currently under investigation and will be implemented in a second continuous fountain (FOCS2).

•Jan 1, 2006•0 citations

An intense, highly collimated continous cesium fountain

N. Castagna

The realisation of cold and slow atomic beams has opened the way to a series of precision measurements of high scientific interest, as atom interferometry, Bose-Einstein Condensation and atomic fountain clocks. The latter are used since several years as reference clocks, given the high performance that they can reach both in accuracy and stability. The common philosophy in the construction of atomic fountains has been the pulsed technique, where an atoms sample is launched vertically and then falls down under the effect of the gravity. The Observatoire de Neuchâtel had a different approach and has built a fountain clock (FOCS1) operating in a continuous mode. This technique offers two main advantages: the diminution of the undesirable effects due to the atomic density (e.g. collisions between the atoms and cavity pulling) and to the noise of the local oscillator (intermodulation effect). To take full advantage of the continuous fountain approach however, we need to increase the atomic flux. The techniques chosen to reach this goal are an efficient transverse collimation together with more atoms to begin with. Here we report on a study of different transverse collimation techniques performed in a two-dimensional phase stable optical lattice (namely gray molasses and magnetically induced laser cooling) as well as the development and characterisation of a 2D-magneto-optical trap used to load the fountain. Best performances are reached in a 2D+-MOT configuration of such a pre-source, for which we detect an atomic flux 20 times greater than the one measured when the fountain is loaded by a Cs vapour. This gain could improve the atomic clock stability by a factor 6. An even better stability is expected after introducing a pre-cooling stage before performing the transverse collimation. This new configuration is currently under investigation and will be implemented in a second continuous fountain (FOCS2).

•Jan 1, 2006•0 citations
To achieve a primary frequency standard based on a continuous fountain of laser cooled cesium atoms, we report on the production of a bright, slow and cold continuous atomic beam. Atoms are cooled from a thermal vapor in a 45/spl deg/ laser geometry and launched directly from the optical molasses by the moving molasses technique. The effects of the source fluorescence on the continuous beam (average velocity, temperature and flux) have been observed, and ways to optimize simultaneously the atomic capture and the continuous beam are presented. Flux measurements rise to 2/spl times/10/sup 8/ at/s from a 2D magneto-optical trap at 7 m/s. The initial velocity is easily tunable from 1 to 10 m/s. If the longitudinal temperature is about 70 /spl mu/K, additional transverse cooling even reduces the transverse temperature in one dimension below 30 /spl mu/K. By extrapolating the obtained atomic flux to the continuous fountain under construction, we expect a short-term stability of 7/spl times/10/sup -14//spl tau//sup -1/2/. Other applications of continuous beams of cold atoms are suggested.
By the moving molasses technique we have extracted laser-cooled cesium atoms in a continuous way directly from an optical molasses. The mean launching velocity is precisely tunable from 1 to 12 m/s. The atomic beam has a flux of $1.3\ifmmode\times\else\texttimes\fi{}{10}^{8} \mathrm{a}\mathrm{t}\mathrm{o}\mathrm{m}/\mathrm{s}$ at 7 m/s and a longitudinal temperature of $70 \ensuremath{\mu}\mathrm{K},$ which represents the highest flux and lowest velocity spread obtained so far in a continuous beam of cold atoms. These features makes it well suited for atomic fountains. The atomic flux can be slightly increased in a two-dimensional magneto-optical trap operation (+40(+40%).(+40 A simple model accounts for the observed dependence of the flux with the magnetic-field gradient.
We present a 2D magneto-optical trap (MOT) that uses an innovative simple optical configuration. Instead of mirrors and quarter-wave plates we use metal-coated retro-reflecting prisms so as to recycle the optical power of the cooling laser beam. We have characterised this source for three different configurations: with and without transverse magnetic field gradient, as well as with a pusher beam to produce a 2D+-MOT. The longitudinal velocity is about 25 m·s-1, with a transverse velocity spread ≤ 1 m·s-1, while the typical atomic flux density can be as much as 1.3×1014 at·s-1·m-2 for a cesium vapour pressure of ~4×10-8 mbar in the source. We use this low velocity atomic beam, instead of thermal vapour, to load a 3D moving optical molasses that launches a continuous cold cesium fountain. We achieve a gain of a factor ~ 20 in the fountain's atomic flux.
We describe the design and performance of a slow atom source based on a 2D magneto-optical trap (MOT) that uses an innovative simple optical configuration. Metal-coated retro-reflecting prisms replace mirrors and quarter-wave plates so the optical power of the cooling laser beam is recycled. This source has been characterised for three different configurations: with and without transverse magnetic field gradient, and with a pusher beam to obtain a 2D+-MOT. The longitudinal velocity is of the order of 25 m·s−1, with a transverse velocity spread ≤1 m·s−1, while the typical atomic flux density obtained is up to 1.3×1014 at ·s−1·m−2 for a cesium vapour pressure of ~4×10−8 mbar in the source. We use this slow atom beam, instead of cesium vapour, to load a 3D moving optical molasses that feeds a continuous cold atom fountain. We obtain a gain of a factor ~20 in the atomic flux launched by the fountain.
We demonstrate launching of laser-cooled Yb atoms in a continuous atomic beam. The continuous cold beam has significant advantages over the more-common pulsed fountain, which was also demonstrated by us recently. The cold beam is formed in the following steps---(i) Atoms from a thermal beam are first Zeeman slowed to a small final velocity, (ii) the slowed atoms are captured in a two-dimensional magneto-optic trap (2D-MOT), and (iii) atoms are launched {\em continuously} in the vertical direction using two sets of moving-molasses beams, inclined at ±15∘\pm 15^\circ±15∘ to the vertical. The cooling transition used is the strongly-allowed 1S0→1P1{^1S}_0 \rightarrow {^1P}_11S0​→1P1​ transition at 399 nm. We capture about 7×1067 \times 10^67×106 atoms in the 2D-MOT, and then launch them with a vertical velocity of 13 m/s at a longitudinal temperature of 125(6) mK.
The realisation of cold and slow atomic beams has opened the way to a series of precision measurements of high scientific interest, as atom interferometry, Bose-Einstein Condensation and atomic fountain clocks. The latter are used since several years as reference clocks, given the high performance that they can reach both in accuracy and stability. The common philosophy in the construction of atomic fountains has been the pulsed technique, where an atoms sample is launched vertically and then falls down under the effect of the gravity. The Observatoire de Neuchâtel had a different approach and has built a fountain clock (FOCS1) operating in a continuous mode. This technique offers two main advantages: the diminution of the undesirable effects due to the atomic density (e.g. collisions between the atoms and cavity pulling) and to the noise of the local oscillator (intermodulation effect). To take full advantage of the continuous fountain approach however, we need to increase the atomic flux. The techniques chosen to reach this goal are an efficient transverse collimation together with more atoms to begin with. Here we report on a study of different transverse collimation techniques performed in a two-dimensional phase stable optical lattice (namely gray molasses and magnetically induced laser cooling) as well as the development and characterisation of a 2D-magneto-optical trap used to load the fountain. Best performances are reached in a 2D+-MOT configuration of such a pre-source, for which we detect an atomic flux 20 times greater than the one measured when the fountain is loaded by a Cs vapour. This gain could improve the atomic clock stability by a factor 6. An even better stability is expected after introducing a pre-cooling stage before performing the transverse collimation. This new configuration is currently under investigation and will be implemented in a second continuous fountain (FOCS2).
The realisation of cold and slow atomic beams has opened the way to a series of precision measurements of high scientific interest, as atom interferometry, Bose-Einstein Condensation and atomic fountain clocks. The latter are used since several years as reference clocks, given the high performance that they can reach both in accuracy and stability. The common philosophy in the construction of atomic fountains has been the pulsed technique, where an atoms sample is launched vertically and then falls down under the effect of the gravity. The Observatoire de Neuchâtel had a different approach and has built a fountain clock (FOCS1) operating in a continuous mode. This technique offers two main advantages: the diminution of the undesirable effects due to the atomic density (e.g. collisions between the atoms and cavity pulling) and to the noise of the local oscillator (intermodulation effect). To take full advantage of the continuous fountain approach however, we need to increase the atomic flux. The techniques chosen to reach this goal are an efficient transverse collimation together with more atoms to begin with. Here we report on a study of different transverse collimation techniques performed in a two-dimensional phase stable optical lattice (namely gray molasses and magnetically induced laser cooling) as well as the development and characterisation of a 2D-magneto-optical trap used to load the fountain. Best performances are reached in a 2D+-MOT configuration of such a pre-source, for which we detect an atomic flux 20 times greater than the one measured when the fountain is loaded by a Cs vapour. This gain could improve the atomic clock stability by a factor 6. An even better stability is expected after introducing a pre-cooling stage before performing the transverse collimation. This new configuration is currently under investigation and will be implemented in a second continuous fountain (FOCS2).