Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Photonics Technology Letters

Suppression of Relative Intensity Noise in Fiber-Optic Raman Polarizers

Victor V. Kozlov, Stefan W. Wabnitz

Published May 20, 2011• 12 citations
Publisher

Abstract

We propose a method for the suppression of relative intensity noise (RIN) at the output of a Raman polarizer, a special type of Raman amplifier that transforms an input weak beam of unpolarized light into an highly polarized amplified beam towards its output. We show that the RIN which is induced by polarization-dependent gain is suppressed whenever the Raman polarizer works in the depleted pump regime.

DOI
10.1109/lpt.2011.2157119

Related papers

Multichannel Raman polarizer with suppressed relative intensity noise for wavelength division multiplexing transmission lines

Victor V. Kozlov, Javier Nuño, Juan Diego Ania‐Castañón +1 more

We propose a method of suppressing the relative intensity noise caused by polarization-dependent gain that is inherent to Raman polarizers (RPs). This method involves bit-synchronously scrambling the state of polarization of a pulse (bit) before the pulse enters the RP. The proposed solution works for RPs operating in a depleted regime and is compatible with multichannel configurations.

Optics Letters•May 29, 2012•12 citations

Polarization-Dependent Gain in Raman Fiber Amplifiers with Depleted Pumps

Nawfel Azami

Polarization-dependent gain in a Raman fiber amplifier in the depleted pump regime is investigated. Numerical investigations are realized and show that gain fluctuations are highly reduced when signal and pump interactions allow pump depletion.

Fiber & Integrated Optics•Aug 22, 2007•0 citations

Study of noise properties in optical distributed Raman amplifiers using a semiclassical model

Philippe B. Gallion, Virginie Dallot, Edouard Bridoux

Using the semiclassical approach the gain and the noise powers, associated to signal and, generated in optical Raman amplifiers, are estimated for forward and backward configurations. Because it combines a corpuscular approach to a phase-amplitude description of the optical field and of the associated noise, this classical formalism allows to identify, to distinguish and to evaluate the respective noise contributions linked, first, to incident fields, such as input zero-point fluctuations, and relative intensity noise associated to the pump, and to the amplifier itself due to the electron momentum fluctuations at the optical frequency. The contribution of Rayleigh backscattering and pump depletion effects are taken into account. For both configurations, the effects of gain and pump power distribution on noise generation are underlined. The determination of the origin and of the amount of intensity noise at the output constitutes a first step toward the amplification of signal with reduced noise amount in Raman amplifiers.

Physics and simulation of optoelectronic devices. Conference•Jan 1, 2002•0 citations

Noise properties in optically distributed Raman amplifiers using a semiclassical model

Philippe B. Gallion, Virginie Dallot, Edouard Bridoux

Using the semiclassical approach the gain and noise powers, associated to signal and, generated in optical Raman amplifiers, are estimated for forward and backward configurations. Because it combines a corpuscular approach to a phase-amplitude description of the optical field and of the associated noise, this classical formalism allows to identify, to distinguish and to evaluate the respective noise contributions linked, first, to incident fields, such as input zero-point fluctuations, and relative intensity noise associated to the pump, and to the amplifier itself due to the electron momentum fluctuations at the optical frequency. The contribution of Rayleigh backscattering and pump depletion effects are taken into account. For both configurations, the effects of gain and pump power distribution on noise generation are underlined. The determination of the origin and of the amount of intensity noise at the output constitutes a first step toward the amplification of signal with reduced noise amount in Raman amplifiers.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 12, 2002•1 citation

Raman gain suppression with multimode lasers

Richard M. Heinrichs, Irwin C. Winkler

We have found the gain of a Raman amplifier to be almost completely suppressed when the amplifier is pumped by a multilongitudinal mode laser and seeded with an initially uncorrelated Stokes beam that is nearly as intense as the pump. This effect is predicted by a plane-wave model of Raman amplification that accounts for multimode pump and Stokes fields. Our experiments have also demonstrated that the beam quality of the pump is maintained to the extent that the amplification is suppressed.

Physical Review A•Jan 1, 1990•1 citation

Stimulated Raman Scattering for All Optical Switches

Ariel Flores-Rosas, Evgeny A. Kuzin, Orlando Díaz-Hernández +4 more

We theoretically and experimentally investigate an all optical switch based on stimulated Raman scattering in optical fibers. The experimental setup consists of a Raman circuit of two stages connected in series through a bandpass filter. In the first stage, we have a saturated amplifier, in this stage the pump pulses are saturated when pump and signal are launched to the input or the pump pulses remain without saturation when pump only is launched at the input. The second stage works as the Raman amplifier; for this stage amplification is directly dependent on the pump power entering from the first stage. For the case when pump pulse only is launched at the input pass to the second stage without saturation and amplifies the signal entering in the second stage, very intense signal pulses appear at the output of this stage. For the case when both pump and signal pulses are launched to the input, the pump pulse is saturated in the first stage and the filter rejected the amplified signal, so that only low power pump enters the second stage and consequently no signal pulses appear at the output. We show that the contrast can be improved when using fibers with normal and anomalous dispersion connected in series in the first stage. The best contrast (the ratio of energies) obtained was 15 dB at 6 W pump peak power.

InTech eBooks•Feb 15, 2017•0 citations
We propose a method for the suppression of relative intensity noise (RIN) at the output of a Raman polarizer, a special type of Raman amplifier that transforms an input weak beam of unpolarized light into an highly polarized amplified beam towards its output. We show that the RIN which is induced by polarization-dependent gain is suppressed whenever the Raman polarizer works in the depleted pump regime.
Using the semiclassical approach the gain and the noise powers, associated to signal and, generated in optical Raman amplifiers, are estimated for forward and backward configurations. Because it combines a corpuscular approach to a phase-amplitude description of the optical field and of the associated noise, this classical formalism allows to identify, to distinguish and to evaluate the respective noise contributions linked, first, to incident fields, such as input zero-point fluctuations, and relative intensity noise associated to the pump, and to the amplifier itself due to the electron momentum fluctuations at the optical frequency. The contribution of Rayleigh backscattering and pump depletion effects are taken into account. For both configurations, the effects of gain and pump power distribution on noise generation are underlined. The determination of the origin and of the amount of intensity noise at the output constitutes a first step toward the amplification of signal with reduced noise amount in Raman amplifiers.
Using the semiclassical approach the gain and noise powers, associated to signal and, generated in optical Raman amplifiers, are estimated for forward and backward configurations. Because it combines a corpuscular approach to a phase-amplitude description of the optical field and of the associated noise, this classical formalism allows to identify, to distinguish and to evaluate the respective noise contributions linked, first, to incident fields, such as input zero-point fluctuations, and relative intensity noise associated to the pump, and to the amplifier itself due to the electron momentum fluctuations at the optical frequency. The contribution of Rayleigh backscattering and pump depletion effects are taken into account. For both configurations, the effects of gain and pump power distribution on noise generation are underlined. The determination of the origin and of the amount of intensity noise at the output constitutes a first step toward the amplification of signal with reduced noise amount in Raman amplifiers.
We theoretically and experimentally investigate an all optical switch based on stimulated Raman scattering in optical fibers. The experimental setup consists of a Raman circuit of two stages connected in series through a bandpass filter. In the first stage, we have a saturated amplifier, in this stage the pump pulses are saturated when pump and signal are launched to the input or the pump pulses remain without saturation when pump only is launched at the input. The second stage works as the Raman amplifier; for this stage amplification is directly dependent on the pump power entering from the first stage. For the case when pump pulse only is launched at the input pass to the second stage without saturation and amplifies the signal entering in the second stage, very intense signal pulses appear at the output of this stage. For the case when both pump and signal pulses are launched to the input, the pump pulse is saturated in the first stage and the filter rejected the amplified signal, so that only low power pump enters the second stage and consequently no signal pulses appear at the output. We show that the contrast can be improved when using fibers with normal and anomalous dispersion connected in series in the first stage. The best contrast (the ratio of energies) obtained was 15 dB at 6 W pump peak power.