Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wuhan University Journal of Natural Sciences

Optical switching and digital signal amplification using an optical fiber grating OBD

Qian Song, Yuancheng Zhang

Published Dec 1, 1997• 0 citations
Publisher

Abstract

It is proposed that an optical fiber grating bistability device may be used for an all-optical switching or an all-optical digital signal amplifier with low power and high speed. The principle, characteristic and parameter are analysed, and some design ideas are given.
DOI
10.1007/bf02830248

Related papers

Optical Switching and Digital Optical Signal Amplification Using a Fiber Grating OBD

D Cenler

It is proposed that an Er doped fiber bistability device with fiber gratings may be used as an all optical switch or a digital signal amplifier of low power and high speed. And, the device is one dimensionally integratable along the fiber. The operation, characteristics, and parameters of these devices are analysed and calculated to give a design principle.

Chinese Journal of Lasers•Jan 1, 1998•1 citation

Digital optical signal amplifier using an Er-doped fiber optical bistable device

Yuancheng Zhang, Jixing Li, Qian Song

The principle and charecteristics of verious digital optical signal amplifiers using Er-doped fiber optical bistability devices have been discussed. Optical signal gain and its variation with the parameters of the devices with constant or pulse optical bias have been calculated, and the design principle of those devices has been given.

Wuhan University Journal of Natural Sciences•Mar 1, 1997•2 citations

Optical fiber grating bistability

Yuancheng Zhang, Qian Song

It is proposed that a segment of Er-doped fiber with a couple of fiber gratings on the ends may be used as a novel optical bistability device with low power and high speed. Operation and bistability threshold of device are analysed in accordance with the distributed feedback couple-mode theory and the nonlinear characteristic of Er-doped fiber. It is shown that a nanoseconds microwatts bistable operation of a centimeter device is realizable under nowaday technological condition.

Wuhan University Journal of Natural Sciences•Dec 1, 1997•1 citation

Optical switching method based on two diffraction gratings bistable system

Piotr A. Kisała, Sławomir Cięszczyk

This paper presents properties of all-optical bistable fibre switch using two fibre Bragg gratings and rare earth elements doped optical fiber. It is not possible to obtain bistable properties at low switching power level in case of a single fibre grating. In this article the method of optical switching that uses all-optical switch has been proposed. It has been achieved by varying the refractive index of nonlinear optical material as a result of light signal amplitude changes. Presented optical bistable device can be used both in contemporary optically switched networks as well as in optoelectronic sensors, owing to their high achievable resolution.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 12, 2014•6 citations

A study and modeling of Fabry-Perot cavities with rare earth doped fiber

Sławomir Cięszczyk, Jacek Klimek, Krzysztof Skorupski +1 more

This paper presents properties of all-optical bistable fibre switch using two fibre Bragg gratings and rare earth elements doped optical fiber. It is not possible to obtain bistable properties at low switching power level in case of a single fibre grating. In this article the method of optical switching that uses all-optical switch has been proposed. It has been achieved by varying the refractive index of nonlinear optical material as a result of light signal amplitude changes. Presented optical bistable device can be used both in contemporary optically switched networks as well as in optoelectronic sensors, owing to their high achievable resolution.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 12, 2014•6 citations

Low-switching power (<45 mW) optical bistability based on optical nonlinearity of ytterbium-doped fiber with a fiber Bragg grating pair

Zhigang Zang, Yujun Zhang

We propose a new optical bistable device (OBD), which is constructed by connecting two symmetrical fiber Bragg gratings with a ytterbium-doped fiber to form a nonlinear Fabry–Perot cavity. The principle of this new OBD is described using the transfer-matrix method, and the two groups of transmitted and reflected optical bistability loops under different parameters are investigated symmetrically. Compared with single fiber Bragg grating switching, whose switching power is greater than 2 kW, this new device has evident merits in reducing the switching power to less than 45 mW.

Journal of Modern Optics•Oct 14, 2011•127 citations
This paper presents properties of all-optical bistable fibre switch using two fibre Bragg gratings and rare earth elements doped optical fiber. It is not possible to obtain bistable properties at low switching power level in case of a single fibre grating. In this article the method of optical switching that uses all-optical switch has been proposed. It has been achieved by varying the refractive index of nonlinear optical material as a result of light signal amplitude changes. Presented optical bistable device can be used both in contemporary optically switched networks as well as in optoelectronic sensors, owing to their high achievable resolution.
This paper presents properties of all-optical bistable fibre switch using two fibre Bragg gratings and rare earth elements doped optical fiber. It is not possible to obtain bistable properties at low switching power level in case of a single fibre grating. In this article the method of optical switching that uses all-optical switch has been proposed. It has been achieved by varying the refractive index of nonlinear optical material as a result of light signal amplitude changes. Presented optical bistable device can be used both in contemporary optically switched networks as well as in optoelectronic sensors, owing to their high achievable resolution.
We propose a new optical bistable device (OBD), which is constructed by connecting two symmetrical fiber Bragg gratings with a ytterbium-doped fiber to form a nonlinear Fabry–Perot cavity. The principle of this new OBD is described using the transfer-matrix method, and the two groups of transmitted and reflected optical bistability loops under different parameters are investigated symmetrically. Compared with single fiber Bragg grating switching, whose switching power is greater than 2 kW, this new device has evident merits in reducing the switching power to less than 45 mW.