Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physical review. B, Condensed matter

Impedance of radio-frequency-biased resistive superconducting quantum interference devices

Robert J. Soulen, Deborah van Vechten

Published Jul 1, 1987• 13 citations
Publisher

Abstract

We have measured with high accuracy (100 ppm) and high precision (5--10 ppm) the impedance of a rf-driven resistive superconducting quantum interference device (SQUID) as a function of the amplitude and frequency of the radio-frequency (rf) bias, as a function of the current bias, and as a function of several other circuit parameters. We have developed the coupled differential equations for the resistive SQUID and for the rf tank circuit. The fit of the solutions of these equations to the data for nonhysteretic junctions is excellent. We were unable to develop solutions for the hysteretic case and thus simply present examples of typical data obtained in order to illustrate the differences with the nonhysteretic case. The relationship of this study to noise thermometry using resistive SQUID's is indicated.

DOI
10.1103/physrevb.36.239

Related papers

Experimental study of amplitude–frequency characteristics of high-transition-temperature radio frequency superconducting quantum interference devices

Xian-Lin Zeng, Y. Zhang, Boris Chesca +3 more

We measured the amplitude–frequency characteristics of radio frequency superconducting quantum interference devices (rf SQUIDs) over a temperature range between 65 and 79 K. Using the expressions derived from the recently developed rf SQUID theory, valid also at large thermal fluctuations, we determined from these data the basic parameters of high-transition-temperature superconductor (HTS) rf SQUIDs. These parameters were: (a) the high-frequency coupling coefficient between the rf SQUID and the tank circuit resonator, k, (b) the SQUIDs hysteretic parameter, β, (c) the critical current of the Josephson junction, Ic, (d) its normal resistance, Rn, and (e) its noise parameter, Γ. We found a good agreement with the values of β(Ic) and Rn determined directly after destructively opening the SQUID loop. In accordance with the theoretical predictions, our experimental results show that at large thermal fluctuation levels (T≅77 K), rf SQUIDs with large loop inductance operate in nonhysteretic mode up to β values exceeding 3. Furthermore, we have shown that the optimal energy sensitivity is attained in the nonhysteretic mode at a value of β distinctly higher than 1. A quantitative comparison of white noise predicted by the theory with that obtained from the experiment showed a reasonable agreement. We also discussed the contribution of the phase information to the SQUID’s signal and noise at optimum operation conditions, when a mixer was used as a signal detector.

Journal of Applied Physics•Dec 1, 2000•13 citations

Influence of the tank circuit on the low frequency impedance of an rf-biased R-SQUID

Heikki Seppä

The dc -impedance of an rf-biased R-SQUID is studied analytically for the nonhysteretic regime. A mathematical analysis of the intrinsic behavior of an R-SQUID, including the mutual interaction between the tank circuit and the SQUID loop, is presented. The results obtained give good agreement with some experimentally observed features. Although the main aim of the present paper was to find an analytic solution for the dc -impedance of an R-SQUID, the results given here can also be used to estimate the R-SQUID parameters and to optimize the performance of a R-SQUID noise thermometer. The theory presented here also provides a good basis for modelling the noise properties of a Josephson junction noise thermometer.

Journal of Applied Physics•Mar 15, 1984•10 citations

Influence of the Josephson junction on the impedance and noise of a resistive superconductive quantum interference device

Robert J. Soulen, William E. Fogle, Jack H. Colwell +2 more

The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.

Journal of Applied Physics•Oct 15, 1993•4 citations

Inductance mode characteristics of a ceramic YBa2Cu3O7−x radio-frequency superconducting quantum interference device at 77 K

Evgeni V. Il’ichev, A. V. Andreev, Christian S. Jacobsen

Experimental results on some radio-frequency superconducting quantum interference device (rf-SQUID) signal properties are presented. The quantum interferometer was made of ceramic YBa2Cu3O7−x and was due to a low critical current operated in the inductance or nonhysteretic mode. With bias current as reference, amplitude variation, and phase shift of the voltage over the tank circuit coupled to the SQUID were measured simultaneously. It is shown that there is qualitative agreement between calculations based on the resistivity shunted junction model and the data. Moreover, using phase detection, signal instabilities predicted for the rf-SQUID inductance mode were observed. These signal instabilities may be exploited to enhance the transfer coefficient for measured flux-to-output signal.

Journal of Applied Physics•Sep 1, 1993•1 citation

Input impedance of the RF SQUID in high frequency regime

S.S. Tinchev

A simple method is developed for analysis of the RF SQUID in regime, where the bias frequency ω is comparable to the natural R/L frequency of the SQUID ring. The input impedance of the RF SQUID is calculated for various values of the parametersq = \omega L/R\leq \leq \pi/4, signal frequency and detuning of the rf bias frequency from tank circuit resonant frequency. It is shown, that both the input resistance and the input inductance may be positive or negative. Measurement of the real part of the input impedance of a hysteretic RF SQUID are described. The experimental data are in qualitative agreement with the prediction of the theory.

IEEE Transactions on Magnetics•May 1, 1983•0 citations

Analysis of the current-voltage characteristic of the rf SQUID

Philippe Lethuillier

The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.

Journal of Applied Physics•Jun 1, 1993•0 citations
We have measured with high accuracy (100 ppm) and high precision (5--10 ppm) the impedance of a rf-driven resistive superconducting quantum interference device (SQUID) as a function of the amplitude and frequency of the radio-frequency (rf) bias, as a function of the current bias, and as a function of several other circuit parameters. We have developed the coupled differential equations for the resistive SQUID and for the rf tank circuit. The fit of the solutions of these equations to the data for nonhysteretic junctions is excellent. We were unable to develop solutions for the hysteretic case and thus simply present examples of typical data obtained in order to illustrate the differences with the nonhysteretic case. The relationship of this study to noise thermometry using resistive SQUID's is indicated.
We measured the amplitude–frequency characteristics of radio frequency superconducting quantum interference devices (rf SQUIDs) over a temperature range between 65 and 79 K. Using the expressions derived from the recently developed rf SQUID theory, valid also at large thermal fluctuations, we determined from these data the basic parameters of high-transition-temperature superconductor (HTS) rf SQUIDs. These parameters were: (a) the high-frequency coupling coefficient between the rf SQUID and the tank circuit resonator, k, (b) the SQUIDs hysteretic parameter, β, (c) the critical current of the Josephson junction, Ic, (d) its normal resistance, Rn, and (e) its noise parameter, Γ. We found a good agreement with the values of β(Ic) and Rn determined directly after destructively opening the SQUID loop. In accordance with the theoretical predictions, our experimental results show that at large thermal fluctuation levels (T≅77 K), rf SQUIDs with large loop inductance operate in nonhysteretic mode up to β values exceeding 3. Furthermore, we have shown that the optimal energy sensitivity is attained in the nonhysteretic mode at a value of β distinctly higher than 1. A quantitative comparison of white noise predicted by the theory with that obtained from the experiment showed a reasonable agreement. We also discussed the contribution of the phase information to the SQUID’s signal and noise at optimum operation conditions, when a mixer was used as a signal detector.
The dc -impedance of an rf-biased R-SQUID is studied analytically for the nonhysteretic regime. A mathematical analysis of the intrinsic behavior of an R-SQUID, including the mutual interaction between the tank circuit and the SQUID loop, is presented. The results obtained give good agreement with some experimentally observed features. Although the main aim of the present paper was to find an analytic solution for the dc -impedance of an R-SQUID, the results given here can also be used to estimate the R-SQUID parameters and to optimize the performance of a R-SQUID noise thermometer. The theory presented here also provides a good basis for modelling the noise properties of a Josephson junction noise thermometer.
The impedance and noise of a resistive superconductive quantum interference device (R-SQUID) have been measured as a function of the dc and rf currents applied to it. The Josephson junction was adjustable so that data were also taken for several values of the junction critical current. The results were compared with the predictions of a resistively shunted junction (RSJ) model which takes into account the influence of the Josephson junction on the impedance and noise. The agreement was found to be quite good and demonstrates that the noise in the circuit is well understood. Use of the R-SQUID as a noise thermometer below 1 K is assessed in terms of corrections due to the RSJ model. It is demonstrated how the dc and rf currents may be adjusted so that the total noise of the R-SQUID is reduced to within 0.1% of the Johnson noise generated by the resistor alone. Under these conditions, the R-SQUID may be used as a noise thermometer to determine thermodynamic temperature to this inaccuracy from 6 to 700 mK.
Experimental results on some radio-frequency superconducting quantum interference device (rf-SQUID) signal properties are presented. The quantum interferometer was made of ceramic YBa2Cu3O7−x and was due to a low critical current operated in the inductance or nonhysteretic mode. With bias current as reference, amplitude variation, and phase shift of the voltage over the tank circuit coupled to the SQUID were measured simultaneously. It is shown that there is qualitative agreement between calculations based on the resistivity shunted junction model and the data. Moreover, using phase detection, signal instabilities predicted for the rf-SQUID inductance mode were observed. These signal instabilities may be exploited to enhance the transfer coefficient for measured flux-to-output signal.
A simple method is developed for analysis of the RF SQUID in regime, where the bias frequency ω is comparable to the natural R/L frequency of the SQUID ring. The input impedance of the RF SQUID is calculated for various values of the parametersq = \omega L/R\leq \leq \pi/4, signal frequency and detuning of the rf bias frequency from tank circuit resonant frequency. It is shown, that both the input resistance and the input inductance may be positive or negative. Measurement of the real part of the input impedance of a hysteretic RF SQUID are described. The experimental data are in qualitative agreement with the prediction of the theory.
The electrical equations of a resonant circuit fed with a radio-frequency current and inductively coupled to a weakly superconducting loop have been derived. The current-voltage characteristic of the rf superconducting quantum interference device can then be calculated and studied as a function of the junction resistance or of the resonance frequency, enabling its behavior to be better understood. As shown by Kurkijärvi, the large positive slope of the steps and the rounding of the characteristic result from thermal noise. However, in order to explain quantitatively the experimental results concerning, namely, point contact weak links which are generally oxidized or which have several contact points, it is useful to remark that the connection between the two superconductors constituting the Josephson junction may be made from n resistive paths. The mean thermal energy of the fluctuating flux is then close to nkbT instead of kbT if the inductances linking the contact points are large enough, that is, on the order of 10−11 H.