Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physics Procedia

Investigation of Robust CMOS Amplifiers for Josephson-CMOS Hybrid Memories

Hyunjoo Jin, 啓太 桑原, Yuki Yamanashi, Nobuyuki Yoshikaw

Published Jan 1, 2012• 10 citations
Publisher

Abstract

In this paper, we investigated three types of robust and high-speed cryogenic CMOS amplifiers for Josephson-CMOS hybrid memories. One is a cascaded CMOS amplifier and the others are source-follower CMOS amplifiers. The source-follower CMOS amplifiers consist of a first-stage PMOS-input source-follower to shift the input voltage level, and a second-stage self-biased differential amplifier. For the first-stage source-follower, we employed two types of circuits: a single-ended source-follower and a self-biased differential source-follower. We compared their performance and robustness by circuit simulations using a cryogenic device model. It was found that the amplifier with the self-biased differential source-follower has better characteristics in terms of speed, power consumption and robustness. We also measured transient characteristics of the amplifiers at liquid helium temperature and showed that the amplifier with the self-biased differential source-follower has wider and robust bias margins.

DOI
10.1016/j.phpro.2012.06.151

Related papers

DC-biased Suzuki stack circuit for Josephson-CMOS memory applications

Yerzhan Mustafa, Keith Krause, Archit Shah +2 more

Abstract Josephson-CMOS hybrid memory leverages the high speed and low power operation of single-flux quantum logic and the high integration densities of CMOS technology. One of the commonly used type of interface circuits in Josephson-CMOS memory is a Suzuki stack, which is a latching high-voltage driver circuit. Suzuki stack circuits are typically powered by an AC bias voltage that has several limitations such as synchronization and coupling effects. To address these issues, a novel DC-biased Suzuki stack circuit is proposed in this paper. As compared to a conventional AC-biased Suzuki stack circuit, the proposed DC-biased design can provide similar output voltage levels and parameter margins, approximately two times higher operating frequency, and three orders of magnitude lower heat load of bias cables.

Superconductor Science and Technology•Jul 4, 2024•14 citations

Experimental Demonstration of 1.2-Gb/s/Channel Readout Operation of Josephson–CMOS Hybrid Memory

Yuki Hironaka, Nobuyuki Yoshikawa

In this study, we aimed to achieve high-speed readout operations of Josephson–CMOS hybrid memory. We first experimentally evaluated the timing margin in the readout operations of the hybrid memory. In single-channel bit line measurements, we confirmed that the hybrid memory could work at a 1-GHz memory clock frequency with a timing margin as high as 0.63 ns. Subsequently, we designed and measured a Josephson–CMOS hybrid accumulator circuit to demonstrate high-speed read operations of the hybrid memory. The core design of the Josephson–CMOS hybrid memory follows our previous design. We introduced a sequential-access read-only CMOS memory and a single-flux-quantum accumulator into a test circuit, enabling high-speed measurement of Josephson–CMOS hybrid memory with only two high-speed external inputs. We designed and fabricated a test circuit using the Rohm 180-nm CMOS process and the AIST-ADP2 Josephson process. In the measurement, we achieved correct operation of the test circuit, including the readout operation of the 32-b hybrid memory at a memory clock frequency as high as 1.2 GHz, corresponding to a 38.4-Gb/s readout.

IEEE Transactions on Applied Superconductivity•Oct 22, 2024•1 citation

Design and development of a cryogenic semiconductor amplifier for interfacing RSFQ circuits at 4.2 K

S. Wünsch, E. Crocoll, M. Schubert +3 more

There is a great deal of interest in amplifiers with extremely high bandwidth, low noise and low power consumption which interface RSFQ circuits with commercial room temperature electronics or amplifying SFQ pulses. In this special application a hybrid amplifier should interface an RSFQ circuitry with a Josephson junction array quantizer chip (JA-Q) at 4.2 K. The input signal for the amplifier is generated by an RSFQ signal generator and the output signal fed-in to a Josephson array quantizer. A voltage gain of about 10 4 with a pattern frequency of 2 GHz for a good transfer of the SFQ pulses is required. Additionally, the JA-Q requires a high output current at low power consumption of the amplifier at the same time. Various hybrid amplifiers based on commercially available p-HEMT transistors in an embedded microwave design were designed and characterized. For the p-HEMT transistor characterization at cryogenic temperatures the biasing settings according to an optimum between voltage gain A V and low power consumption P V were determined. Thus a power consumption of P V = 2 mW and a voltage gain of about A V = 4 per stage were achieved. For a preamplifier and an amplifier concept a number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers and the combination of the amplifiers and the JA-Q at 4.2 K showed their good performance without any disturbances of the quantized voltage steps.

Superconductor Science and Technology•Oct 18, 2007•6 citations

Cryogenic Semiconductor Amplifier for RSFQ-Circuits With High Data Rates at 4.2 K

S. Wünsch, Thomas Ortlepp, E. Crocoll +2 more

The connection of RSFQ circuits with commercial room temperature electronics and amplifying SFQ pulses with high data rates require cryogenic interface amplifiers. Such amplifiers should provide extremely high bandwidth, low noise and low power consumption at the same time. Various hybrid amplifiers based on commercial p-HEMT transistors in an embedded microwave design were designed and characterized. Towards the p-HEMT transistor characterization at cryogenic temperature the biasing settings according to an optimum between voltage gain and low power consumption were determined. Thus a total power consumption of 2 mW and a voltage gain of 12 dB per single stage were achieved. For a preamplifier and an amplifier concept a multiple number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers, the combination of an amplifier with a RSFQ circuit at 4.2 K showed their good performances without any disturbance of the RSFQ circuit. Due to the losses between the stages a total gain of 25 dB with a four stage amplifier was achieved; pulse rates went up to 3 Gb/s. The total power consumption was in the range of 8 mW. Further increase of data rates will be achieved by improving the matching between RSFQ output stage and amplifier.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•15 citations

Josephson-CMOS Hybrid Memory With Nanocryotrons

Masamitsu Tanaka, Masato Suzuki, Gen Konno +3 more

We present hybridization of Josephson, CMOS, and nanocryotron (nTron) devices for a large-scale cryogenic memory application. The memory system proposed here is dynamic random access memory composed of address decoders based on an energy-efficient rapid single-flux-quantum logic, nTron line drivers, a CMOS memory cell array, and Josephson current sensors. Because drivers with voltage amplification and decoders are the major causes of power dissipation in the conventional Josephson-CMOS hybrid memory, drastic reduction in power consumption is expected. We show estimates that the power consumption of a 16-Mb memory is reduced to 1.36-2.77 mW, approximately 1/12 of the conventional Josephson-CMOS hybrid memory, and the access time is 0.78 ns for a read operation, when we assume a 65-nm CMOS process and a 1.0-μm Nb/AlOx/Nb process. In the preliminary experiment, we fabricated nTrons using NbTiN thin film that are suitable for hybrid memory implementation, and measured with eight-transistor static random access memory cells fabricated using the Rohm 0.18-μm CMOS process. We successfully triggered the nTron into the normal state, and observed output voltage of ~0.1 V at 13.5 K. The experimental results support the potential of the hybrid memory using NbTiN nTrons.

IEEE Transactions on Applied Superconductivity•Dec 30, 2016•40 citations

Cryogenic CMOS circuits for single charge digital readout

Kevin Eng, Thomas M. Gurrieri, Jason Hamlet +1 more

The readout of a solid state qubit often relies on single charge sensitive electrometry. However the combination of fast and accurate measurements is non trivial due to large RC time constants due to the electrometers resistance and shunt capacitance from wires between the cold stage and room temperature. Currently fast sensitive measurements are accomplished through rf reflectrometry. I will present an alternative single charge readout technique based on cryogenic CMOS circuits in hopes to improve speed, signal-to-noise, power consumption and simplicity in implementation. The readout circuit is based on a current comparator where changes in current from an electrometer will trigger a digital output. These circuits were fabricated using Sandia's 0.35 {micro}m CMOS foundry process. Initial measurements of comparators with an addition a current amplifier have displayed current sensitivities of < 1nA at 4.2K, switching speeds up to {approx}120ns, while consuming {approx}10 {micro}W. I will also discuss an investigation of noise characterization of our CMOS process in hopes to obtain a better understanding of the ultimate limit in signal to noise performance.

Bulletin of the American Physical Society•Mar 15, 2010•0 citations
In this paper, we investigated three types of robust and high-speed cryogenic CMOS amplifiers for Josephson-CMOS hybrid memories. One is a cascaded CMOS amplifier and the others are source-follower CMOS amplifiers. The source-follower CMOS amplifiers consist of a first-stage PMOS-input source-follower to shift the input voltage level, and a second-stage self-biased differential amplifier. For the first-stage source-follower, we employed two types of circuits: a single-ended source-follower and a self-biased differential source-follower. We compared their performance and robustness by circuit simulations using a cryogenic device model. It was found that the amplifier with the self-biased differential source-follower has better characteristics in terms of speed, power consumption and robustness. We also measured transient characteristics of the amplifiers at liquid helium temperature and showed that the amplifier with the self-biased differential source-follower has wider and robust bias margins.
Abstract Josephson-CMOS hybrid memory leverages the high speed and low power operation of single-flux quantum logic and the high integration densities of CMOS technology. One of the commonly used type of interface circuits in Josephson-CMOS memory is a Suzuki stack, which is a latching high-voltage driver circuit. Suzuki stack circuits are typically powered by an AC bias voltage that has several limitations such as synchronization and coupling effects. To address these issues, a novel DC-biased Suzuki stack circuit is proposed in this paper. As compared to a conventional AC-biased Suzuki stack circuit, the proposed DC-biased design can provide similar output voltage levels and parameter margins, approximately two times higher operating frequency, and three orders of magnitude lower heat load of bias cables.
In this study, we aimed to achieve high-speed readout operations of Josephson–CMOS hybrid memory. We first experimentally evaluated the timing margin in the readout operations of the hybrid memory. In single-channel bit line measurements, we confirmed that the hybrid memory could work at a 1-GHz memory clock frequency with a timing margin as high as 0.63 ns. Subsequently, we designed and measured a Josephson–CMOS hybrid accumulator circuit to demonstrate high-speed read operations of the hybrid memory. The core design of the Josephson–CMOS hybrid memory follows our previous design. We introduced a sequential-access read-only CMOS memory and a single-flux-quantum accumulator into a test circuit, enabling high-speed measurement of Josephson–CMOS hybrid memory with only two high-speed external inputs. We designed and fabricated a test circuit using the Rohm 180-nm CMOS process and the AIST-ADP2 Josephson process. In the measurement, we achieved correct operation of the test circuit, including the readout operation of the 32-b hybrid memory at a memory clock frequency as high as 1.2 GHz, corresponding to a 38.4-Gb/s readout.
There is a great deal of interest in amplifiers with extremely high bandwidth, low noise and low power consumption which interface RSFQ circuits with commercial room temperature electronics or amplifying SFQ pulses. In this special application a hybrid amplifier should interface an RSFQ circuitry with a Josephson junction array quantizer chip (JA-Q) at 4.2 K. The input signal for the amplifier is generated by an RSFQ signal generator and the output signal fed-in to a Josephson array quantizer. A voltage gain of about 10 4 with a pattern frequency of 2 GHz for a good transfer of the SFQ pulses is required. Additionally, the JA-Q requires a high output current at low power consumption of the amplifier at the same time. Various hybrid amplifiers based on commercially available p-HEMT transistors in an embedded microwave design were designed and characterized. For the p-HEMT transistor characterization at cryogenic temperatures the biasing settings according to an optimum between voltage gain A V and low power consumption P V were determined. Thus a power consumption of P V = 2 mW and a voltage gain of about A V = 4 per stage were achieved. For a preamplifier and an amplifier concept a number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers and the combination of the amplifiers and the JA-Q at 4.2 K showed their good performance without any disturbances of the quantized voltage steps.
The connection of RSFQ circuits with commercial room temperature electronics and amplifying SFQ pulses with high data rates require cryogenic interface amplifiers. Such amplifiers should provide extremely high bandwidth, low noise and low power consumption at the same time. Various hybrid amplifiers based on commercial p-HEMT transistors in an embedded microwave design were designed and characterized. Towards the p-HEMT transistor characterization at cryogenic temperature the biasing settings according to an optimum between voltage gain and low power consumption were determined. Thus a total power consumption of 2 mW and a voltage gain of 12 dB per single stage were achieved. For a preamplifier and an amplifier concept a multiple number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers, the combination of an amplifier with a RSFQ circuit at 4.2 K showed their good performances without any disturbance of the RSFQ circuit. Due to the losses between the stages a total gain of 25 dB with a four stage amplifier was achieved; pulse rates went up to 3 Gb/s. The total power consumption was in the range of 8 mW. Further increase of data rates will be achieved by improving the matching between RSFQ output stage and amplifier.
We present hybridization of Josephson, CMOS, and nanocryotron (nTron) devices for a large-scale cryogenic memory application. The memory system proposed here is dynamic random access memory composed of address decoders based on an energy-efficient rapid single-flux-quantum logic, nTron line drivers, a CMOS memory cell array, and Josephson current sensors. Because drivers with voltage amplification and decoders are the major causes of power dissipation in the conventional Josephson-CMOS hybrid memory, drastic reduction in power consumption is expected. We show estimates that the power consumption of a 16-Mb memory is reduced to 1.36-2.77 mW, approximately 1/12 of the conventional Josephson-CMOS hybrid memory, and the access time is 0.78 ns for a read operation, when we assume a 65-nm CMOS process and a 1.0-μm Nb/AlOx/Nb process. In the preliminary experiment, we fabricated nTrons using NbTiN thin film that are suitable for hybrid memory implementation, and measured with eight-transistor static random access memory cells fabricated using the Rohm 0.18-μm CMOS process. We successfully triggered the nTron into the normal state, and observed output voltage of ~0.1 V at 13.5 K. The experimental results support the potential of the hybrid memory using NbTiN nTrons.
The readout of a solid state qubit often relies on single charge sensitive electrometry. However the combination of fast and accurate measurements is non trivial due to large RC time constants due to the electrometers resistance and shunt capacitance from wires between the cold stage and room temperature. Currently fast sensitive measurements are accomplished through rf reflectrometry. I will present an alternative single charge readout technique based on cryogenic CMOS circuits in hopes to improve speed, signal-to-noise, power consumption and simplicity in implementation. The readout circuit is based on a current comparator where changes in current from an electrometer will trigger a digital output. These circuits were fabricated using Sandia's 0.35 {micro}m CMOS foundry process. Initial measurements of comparators with an addition a current amplifier have displayed current sensitivities of < 1nA at 4.2K, switching speeds up to {approx}120ns, while consuming {approx}10 {micro}W. I will also discuss an investigation of noise characterization of our CMOS process in hopes to obtain a better understanding of the ultimate limit in signal to noise performance.