Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Diffusion-cooled superconducting hot electron bolometer heterodyne mixer between 630 and 820 GHz

Klaus Fiegle, D. Diehl, Karl Jacobs

Published Jun 1, 1997• 13 citations
Publisher

Abstract

We report on heterodyne mixing experiments between 630-820 GHz using a diffusion-cooled superconducting hot electron bolometer at intermediate frequencies from 1-2 GHz. The niobium bolometer which is cooled by diffusion of the hot electrons into a normal conductor has dimensions of 0.3 /spl mu/m/spl times/0.15 /spl mu/m and was fabricated at KOSMA with a two-step electron beam lithography process. The film thickness of the device is 30 nm with T/sub c/ of 6.1 K and /spl Delta/T/sub c/ of 0.7 K. The mixing experiments are performed with a tunerless waveguide mixer block previously used for very low-noise SIS receivers. At a physical temperature of 2.2 K, receiver noise temperatures at 666 GHz are 1500 K at 1.0 GHz intermediate frequency, increasing rapidly above 1.5 GHz. The dissipated local oscillator power is evaluated to be 65-90 nW.

DOI
10.1109/77.622165

Related papers

A heterodyne receiver at 533 GHz using a diffusion-cooled superconducting hot electron bolometer mixer

Anders J. Skalare, William R. McGrath, B. Bumble +4 more

This paper describes heterodyne measurements at 533 GHz using a novel superconducting hot electron bolometer in a waveguide mixer block. The bolometer is a thin (10 nm) and narrow (0.1 /spl mu/m) strip of niobium with a length of less than half a micron and a critical temperature of approximately 5.5 K. The short length ensures that diffusion dominates over electron-phonon interaction as a cooling mechanism for the hot electrons, thus allowing heterodyne detection with intermediate frequencies of several GHz. A Y-factor response of 1.15 dB has been obtained at an intermediate frequency of 1.4 GHz with hot/cold load temperatures of approximately 295/77 K, indicating a receiver noise temperature around 650 K DSB. The IF response extends up to at least 2 GHz and possibly higher.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•32 citations

A low-noise 2.5 THz superconductive Nb hot-electron mixer

Boris S. Karasik, Michael C. Gaidis, William R. McGrath +2 more

We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•32 citations

Measurements with a Diffusion-Cooled Nb Hot-Electron Bolometer Mixer at 1100 GHz

Anders J. Skalare, William R. McGrath, B. Bumble +1 more

In this paper we report receiver sensitivity measurements with a diffusion-cooled niobium hot-electron bolometer around 1100 GHz. The lowest receiver noise temperature was 1670 K DSB, with approximately 40 nW of local oscillator power being dissipated in the device. The intermediate frequency bandwidth of this device, due to its short length (0.15 gm) and low normal resistance (43 a), exceeded the 1.8 GHz bandwidth of the measurement setup. The receiver was used to detect the sulfur dioxide gas absorption line at 1102 GHz in a heterodyne mode.

•Mar 1, 1998•9 citations

Fabrication and characterisation of a Nb diffusion-cooled hot electron bolometer for a 730 GHz waveguide mixer

D. Wilms Floet, No Value Gao, W. Hulshoff +3 more

We have fabricated Nb diffusion-cooled hot electron bolometers for a waveguide mixer around 700 GHz. The device in this work is a thin (12 nm) Nb bridge with a length and width of 220 nm and is defined by a two-step electron beam lithography process. The resistance as a function of temperature shows two transitions, which we attribute to the Nb bridge (6.1 K) and to parts of the Nb which are covered by the Au pads (5.4 K). We have measured a DSB receiver noise temperature of 2200 K at 735 GHz and a bath temperature of 3.3 K. No significant increase of the noise temperature is observed at IF frequencies between 1.1 and 1.7 GHz. The coupled LO power is estimated to be 35 nW.

•Jan 1, 1997•0 citations

Large bandwidth and low noise in a diffusion-cooled hot-electron bolometer mixer

Anders J. Skalare, William R. McGrath, B. Bumble +5 more

Heterodyne measurements have been made at 533 GHz using a novel superconducting hot-electron bolometer in a waveguide mixer. The bolometer is a 0.3 μm long niobium microbridge with a superconducting transition temperature of 5 K. The short length ensures that electron diffusion dominates over electron-phonon interactions as the electron cooling mechanism, which should allow heterodyne detection with intermediate frequencies (if) of several GHz. A Y-factor response of 1.15 dB has been obtained at an if of 1.4 GHz with 77 and 295 K loads, indicating a receiver noise temperature of 650 K DSB. The −3 dB rolloff in the if response occurs at 1.7 GHz.

Applied Physics Letters•Mar 11, 1996•73 citations

Low-noise and wideband hot-electron superconductive mixers for THz frequencies

Boris S. Karasik, Anders J. Skalare, Rolf A. Wyss +5 more

Superconductive hot-electron bolometer (HEB) mixers have been built and tested in the frequency range 1.1-2.5 THz. The mixer device is a 0.15-03 /spl mu/m microbridge made from a 10 nm thick Nb film. This device employs diffusion as a cooling mechanism for hot electrons. The double sideband noise temperature was measured to be /spl les/3000 K at 2.5 THz and the mixer IF bandwidth is /spl ap/9-10 GHz for a 0.1 /spl mu/m long device. The local oscillator (LO) power dissipated in the HEB microbridge was 20-100 nW. Further improvement of the mixer characteristics can be potentially achieved by using Al microbridges. The advantages and parameters of such devices are evaluated The HEB mixer Is a primary candidate for ground based, airborne and spaceborne heterodyne instruments at THz frequencies. HEB receivers are planned for use on the NASA Stratospheric Observatory for Infrared Astronomy (SOFIA) and the ESA Far Infrared and Submillimeter Space Telescope (FIRST). The prospects of a submicron-size YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// (YBCO) HEB are also discussed. The expected LO power of 1-10 /spl mu/W and SSB noise temperature of /spl ap/2000 K may make this mixer attractive for various remote sensing applications.

IEEE International Conference on Terahertz Electronics (THz)•Nov 27, 2002•5 citations
We report on heterodyne mixing experiments between 630-820 GHz using a diffusion-cooled superconducting hot electron bolometer at intermediate frequencies from 1-2 GHz. The niobium bolometer which is cooled by diffusion of the hot electrons into a normal conductor has dimensions of 0.3 /spl mu/m/spl times/0.15 /spl mu/m and was fabricated at KOSMA with a two-step electron beam lithography process. The film thickness of the device is 30 nm with T/sub c/ of 6.1 K and /spl Delta/T/sub c/ of 0.7 K. The mixing experiments are performed with a tunerless waveguide mixer block previously used for very low-noise SIS receivers. At a physical temperature of 2.2 K, receiver noise temperatures at 666 GHz are 1500 K at 1.0 GHz intermediate frequency, increasing rapidly above 1.5 GHz. The dissipated local oscillator power is evaluated to be 65-90 nW.
This paper describes heterodyne measurements at 533 GHz using a novel superconducting hot electron bolometer in a waveguide mixer block. The bolometer is a thin (10 nm) and narrow (0.1 /spl mu/m) strip of niobium with a length of less than half a micron and a critical temperature of approximately 5.5 K. The short length ensures that diffusion dominates over electron-phonon interaction as a cooling mechanism for the hot electrons, thus allowing heterodyne detection with intermediate frequencies of several GHz. A Y-factor response of 1.15 dB has been obtained at an intermediate frequency of 1.4 GHz with hot/cold load temperatures of approximately 295/77 K, indicating a receiver noise temperature around 650 K DSB. The IF response extends up to at least 2 GHz and possibly higher.>
We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.
In this paper we report receiver sensitivity measurements with a diffusion-cooled niobium hot-electron bolometer around 1100 GHz. The lowest receiver noise temperature was 1670 K DSB, with approximately 40 nW of local oscillator power being dissipated in the device. The intermediate frequency bandwidth of this device, due to its short length (0.15 gm) and low normal resistance (43 a), exceeded the 1.8 GHz bandwidth of the measurement setup. The receiver was used to detect the sulfur dioxide gas absorption line at 1102 GHz in a heterodyne mode.
We have fabricated Nb diffusion-cooled hot electron bolometers for a waveguide mixer around 700 GHz. The device in this work is a thin (12 nm) Nb bridge with a length and width of 220 nm and is defined by a two-step electron beam lithography process. The resistance as a function of temperature shows two transitions, which we attribute to the Nb bridge (6.1 K) and to parts of the Nb which are covered by the Au pads (5.4 K). We have measured a DSB receiver noise temperature of 2200 K at 735 GHz and a bath temperature of 3.3 K. No significant increase of the noise temperature is observed at IF frequencies between 1.1 and 1.7 GHz. The coupled LO power is estimated to be 35 nW.
Heterodyne measurements have been made at 533 GHz using a novel superconducting hot-electron bolometer in a waveguide mixer. The bolometer is a 0.3 μm long niobium microbridge with a superconducting transition temperature of 5 K. The short length ensures that electron diffusion dominates over electron-phonon interactions as the electron cooling mechanism, which should allow heterodyne detection with intermediate frequencies (if) of several GHz. A Y-factor response of 1.15 dB has been obtained at an if of 1.4 GHz with 77 and 295 K loads, indicating a receiver noise temperature of 650 K DSB. The −3 dB rolloff in the if response occurs at 1.7 GHz.
Superconductive hot-electron bolometer (HEB) mixers have been built and tested in the frequency range 1.1-2.5 THz. The mixer device is a 0.15-03 /spl mu/m microbridge made from a 10 nm thick Nb film. This device employs diffusion as a cooling mechanism for hot electrons. The double sideband noise temperature was measured to be /spl les/3000 K at 2.5 THz and the mixer IF bandwidth is /spl ap/9-10 GHz for a 0.1 /spl mu/m long device. The local oscillator (LO) power dissipated in the HEB microbridge was 20-100 nW. Further improvement of the mixer characteristics can be potentially achieved by using Al microbridges. The advantages and parameters of such devices are evaluated The HEB mixer Is a primary candidate for ground based, airborne and spaceborne heterodyne instruments at THz frequencies. HEB receivers are planned for use on the NASA Stratospheric Observatory for Infrared Astronomy (SOFIA) and the ESA Far Infrared and Submillimeter Space Telescope (FIRST). The prospects of a submicron-size YBa/sub 2/Cu/sub 3/O/sub 7-/spl delta// (YBCO) HEB are also discussed. The expected LO power of 1-10 /spl mu/W and SSB noise temperature of /spl ap/2000 K may make this mixer attractive for various remote sensing applications.