Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Letters

Optical bistability in asymmetric Fabry–Perot laser-diode amplifiers

N. F. Mitchell, John C. Connolly, James O’Gorman, J. Hegarty

Published Feb 15, 1994• 28 citations
Publisher

Abstract

We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.

DOI
10.1364/ol.19.000269

Related papers

Optical bistability and X-shaped hysteresis in laser diode amplifiers

N. F. Mitchell, James O’Gorman, John Hegarty +1 more

Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>

IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS)•Dec 30, 2002•4 citations

Reflective bistability in 1.55 μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.

•Jan 1, 1998•0 citations

Measurements and modeling of reflective bistability in 1.55-μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.

IEEE Journal of Quantum Electronics•Jan 1, 1999•44 citations

Optical bistability using a Fabry–Perot semiconductor-laser amplifier with two holding beams

Hitoshi Kawaguchi, Kyo Inoue, Hiroyuki Tani

Bistable switching of an optical signal beam by a control beam with a different wavelength, using the nonlinearity of a Fabry-Perot semiconductor-laser amplifier, is reported for the first time to the authors' knowledge. Depending on the initial detuning of the optical signal beam, both normal (counterclockwise) and reverse (clockwise) hysteresis are theoretically and experimentally obtained in the signal output power as a function of the control input power.

Optics Letters•Jul 1, 1987•32 citations

A power and wavelength detuning-dependent hysteresis loop in a single mode Fabry—Pérot laser diode

Jian-Wei Wu, Bikash Nakarmi

In this paper, we observe experimentally the optical bistability induced by the side-mode injection power and wavelength detuning in a single mode Fabry—Pérot laser diode (SMFP-LD). Results show that the bistability characteristics of the dominant and injected modes are strongly dependent on the injected input optical power and wavelength detuning in an SMFP-LD. We observe three types of hysteresis loops: counterclockwise, clockwise, and butterfly hysteresis with various loop widths. In the case of a bistability loop caused by injection power, the transition from counterclockwise to clockwise in the hysteresis direction with the wavelength detuning from 0.028 nm to 0.112 nm is observed in a way of butterfly hysteresis for the dominant mode by increasing the wavelength detuning. The width of hysteresis loop, induced by wavelength detuning is also changed while the injection power is enhanced from −7 dBm to −5 dBm.

Chinese Physics B•Aug 1, 2013•2 citations

Optical bistability in InGaAsP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.

Conference on Lasers and Electro-Optics•Jan 1, 1985•0 citations
We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.
Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>
Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.
We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.
In this paper, we observe experimentally the optical bistability induced by the side-mode injection power and wavelength detuning in a single mode Fabry—Pérot laser diode (SMFP-LD). Results show that the bistability characteristics of the dominant and injected modes are strongly dependent on the injected input optical power and wavelength detuning in an SMFP-LD. We observe three types of hysteresis loops: counterclockwise, clockwise, and butterfly hysteresis with various loop widths. In the case of a bistability loop caused by injection power, the transition from counterclockwise to clockwise in the hysteresis direction with the wavelength detuning from 0.028 nm to 0.112 nm is observed in a way of butterfly hysteresis for the dominant mode by increasing the wavelength detuning. The width of hysteresis loop, induced by wavelength detuning is also changed while the injection power is enhanced from −7 dBm to −5 dBm.
We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.