To achieve the high sensitivity requirements of future space based sub‐mm spectroscopy missions is highly challenging. Microwave Kinetic Inductance Detectors are a promising candidate since they can theoretically achieve the performance required. However, they have yet to be shown to reach this performance. We will show that this is due in part to stray light saturating the device’s sensitivity in aluminium KIDs in our experimental setup. We discuss a set of experiments that show that thermal radiation from the 3 K stage of our cooler is limiting the quasiparticle lifetime in our aluminium KIDs. Furthermore we discuss a new filtering method based upon coaxial cable filters to reduce this effect. Using the best filtering achievable we have measured a quasiparticle lifetime of 2.8 msec in a 100 nm thick Al KID.
To achieve the high sensitivity requirements of future space based sub‐mm spectroscopy missions is highly challenging. Microwave Kinetic Inductance Detectors are a promising candidate since they can theoretically achieve the performance required. However, they have yet to be shown to reach this performance. We will show that this is due in part to stray light saturating the device’s sensitivity in aluminium KIDs in our experimental setup. We discuss a set of experiments that show that thermal radiation from the 3 K stage of our cooler is limiting the quasiparticle lifetime in our aluminium KIDs. Furthermore we discuss a new filtering method based upon coaxial cable filters to reduce this effect. Using the best filtering achievable we have measured a quasiparticle lifetime of 2.8 msec in a 100 nm thick Al KID.
Microwave Kinetic Inductance Detectors (MKIDs) are extremely sensitive radiation detectors based on superconducting resonators that can be combined in large arrays on a single readout line within a limited frequency bandwidth. This makes MKIDs ideal detectors for the ultimate far-infrared observatory: a future space-based actively cooled telescope with its performance solely limited by the low universe background radiation. However, to reach these detector requirements, state-of-the-art MKIDs still need a order of magnitude improvement in device sensitivity. In this work, the MKID sensitivity is improved by reducing the aluminium volume that absorbs pair-breaking radiation into quasiparticle excitations, while making sure all radiation is still absorbed. Furthermore, a key requirement is sufficient reduction of excess noise as to keep the device intrinsically limited by thermally driven random fluctuations in the number of quasiparticles in absence of radiation, or Generation-Recombination (G-R) noise. To this end, a model is developed that describes the noise contributions as function of device geometry, readout power, material properties and radiation power. Subsequently, a realistic MKID design is presented and tested that reduces excess noise and maximises the sensitivity, expressed as Noise Equivalent Power (NEP). At high temperatures, good overall agreement is found between the measured noise spectra and the model. At low temperature T = 120 mK, the measurement results give an optical NEP similar to current state-of-the-art MKIDs. The NEP is not as low as expected due to short quasiparticle lifetimes, an unexpected decrease in the G-R noise level and a very high excess noise attributed to Two-Level Systems (TLS) noise that starts to dominate the already low G-R noise spectrum at low temperatures. Possibly, the quick quasiparticle lifetime saturation and noise level drop are caused by a strong readout power effect, as the readout power is known to create excess quasiparticles and to cause a strongly non-thermal electron energy distribution in the aluminium strip of the MKID. However, the exact microscopic details of these effects are unknown and not studied in this project. Based on the current chip design, a straightforward way to improve device performance and study the readout power effect in more detail is a reduction of the high TLS noise levels, which is possibly fabrication related. This would allow an unobstructed view of the G-R noise spectrum at low temperatures, thereby allowing both a study of the readout power effect on the quasiparticle system, and ultimately achieving the improvement in NEP needed reach the detector requirements for the ultimate space-based far-infrared observatory.
Kinetic inductance detectors (KIDs) are superconducting thin-film microresonators that are sensitive photon detectors. These detectors are a candidate for the next generation of experiments designed to measure the polarization of the cosmic microwave background (CMB). I discuss the basic theory needed to understand the response of a KID to light, focusing on the dynamics of the quasiparticle system. I derive an equation that describes the dynamics of the quasiparticle number, solve it in a simplified form not previously published, and show that it can describe the dynamic response of a detector. Magnetic flux vortices in a superconducting thin film can be a significant source of dissipation, and I demonstrate some techniques to prevent their formation. Based on the presented theory, I derive a corrected version of a widely-used equation for the quasiparticle recombination noise in a KID. I show that a KID consisting of a lumped-element resonator can be sensitive enough to be limited by photon noise, which is the fundamental limit for photometry, at a level of optical loading below levels in ground-based CMB experiments. Finally, I describe an ongoing project to develop multichroic KID pixels that are each sensitive to two linear polarization states in two spectral bands, intended for the next generation of CMB experiments. I show that a prototype 23-pixel array can detect millimeter-wave light, and present characterization measurements of the detectors.
We present measurements of quasiparticle generation-recombination noise in aluminium Microwave Kinetic Inductance Detectors, the fundamental noise source for these detectors. Both the quasiparticle lifetime and the number of quasiparticles can be determined from the noise spectra. The number of quasiparticles saturates to 10 μm−3 at temperatures below 160 mK, which is shown to limit the quasiparticle lifetime to 4 ms. These numbers lead to a generation-recombination noise limited noise equivalent power (NEP) of 1.5×10−19 W/Hz1/2. Since NEP∝N qp , lowering the number of remnant quasiparticles will be crucial to improve the sensitivity of these detectors. We show that the readout power now limits the number of quasiparticles and thereby the sensitivity.
Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.
The quasiparticle lifetime is a crucial parameter in achieving a background limited noise equivalent power for kinetic inductance detectors. We present measurements of the quasiparticle lifetime of 150 nm thick sputtered tantalum on silicon kinetic inductance detectors using optical pulses. We find that the quasiparticle lifetime saturates at low temperatures, increases to a maximum of up to 45 μs and subsequently drops with increasing temperature. We attribute this behavior to non-uniformity in the superconductor.
We design and fabricate a 350GHz 8×8 Al Microwave Kinetic Inductance Detector (MKIDs) array for the demonstration of its characteristics, mainly focus on the quasiparticle lifetime of the resonators. The quasiparticle lifetime data is collected by measuring a resonator’s phase response to a LED pulse at resonant frequency in a dilution refrigerator cooled to mK stage. We also measure and discuss the influence of various parameters on the change of quasiparticle lifetime, including different LED voltage supply, bath temperature of the MKIDs, and superconducting film thickness.