IEEE Transactions on Magnetics

Superconductive tapped delay lines for microwave analog signal processing

R.S. Withers, Alfredo C. Anderson, P.V. Wright, Stanley A. Reible

Published May 1, 1983• 44 citations

Abstract

Passive superconducting tapped delay lines have been fabricated for use as matched filters for multigigahertz bandwidth analog signal processing. Specifically, linear frequency-modulated dispersive delay lines, also known as chirp filters, having a bandwidth of 2.6 GHz centered at 4 GHz and a dispersion time of 35 ns have been constructed. The stripline structure consists of a 4000-Å-thick patterned niobium film sandwiched between 5-cm-diameter, 125-μm-thick sapphire wafers. Two parallel striplines, each 1.6-m long, are wound in a spiral pattern. The taps are backward-wave couplers formed by bringing the two lines into and out of proximity at specified locations. Pulse expansion and compression have been demonstrated with these devices and are in close agreement with a new theoretical model for this class of signal processors.

DOI: 10.1109/tmag.1983.1062401

Related papers

Superconductive convolver

Stanley A. Reible, Alfredo C. Anderson, P.V. Wright +2 more

Concepts for realizing superconductive convolvers capable of processing analog signals having bandwidths up to 10 GHz have been developed and are being implemented. A preliminary convolver structure with 19 taps and a 14-ns interaction length has recently been demonstrated. This device employs a superconductive transmission line as a low-loss delay element and superconductive tunnel junctions as nonlinear mixing elements. The niobium delay line provides the relative shifting of signal and reference waveforms, niobium/niobium-oxide/lead mixers with proximity taps provide local multiplication of the two waveforms, and a short output transmission line provides coherent summation of the local products. The principles of device operation, design tradeoffs and experimental results will be presented. Convolvers can provide the essential programmable matched-filter component for extremely wide-bandwidth spread-spectrum communication systems. It appears feasible to produce a convolver with an interaction time of about 100 ns and signal processing gains of up to 1000. This superconductive analog device offers the potential of providing a real-time programmable signal processing function with the digital equivalent of about 1012operations/sec.

IEEE Transactions on MagneticsMay 1, 19836 citations

Research on Superconductive Signal-Processing Devices.

Richard W. Ralston

A new technology utilizing superconductive components to realize convolvers and correlators that are capable of processing analog signals having bandwidths from 2-20 GHz is being developed. The technology has two key features: (1) low-loss and low-dispersion electromagnetic striplines provide tapped delay on compact substrates; and (2) superconductive tunnel junctions provide efficient low-noise mixing and high-speed sampling circuits. A convolver with a time-bandwidth product of 28 has been demonstrated. Projections indicate that superconductive technology should support analog devices with time-bandwidth products of 1000 or greater. Originator-Supplied keywords include: convolver, time integrating correlator, ring correlator, convolution, and supercondcutive signal processing.

Nov 30, 19840 citations

Superconductive convolver with junction ring mixers

Stanley A. Reible

A superconductive convolver with tunnel-junction ring mixers has been developed and demonstrated as a programmable matched filter for near 1-GHz-bandwidth chirped waveforms. A low-loss, 14-ns-long superconductive stripline circuit provides temporary storage and relative shifting of signal and reference waveforms. These waveforms are sampled by 25 proximity tap pairs and local multiplication is performed by 25 junction ring mixers. Two short transmission lines coherently sum the local products and deliver the convolution output. The output power level of the convolver has been increased 18 dB by the incorporation of ring mixers and other output circuit improvements. These mixers employ series arrays of niobium/niobium oxide/lead junctions driven by delay-line taps in a quasi-balanced manner. The ring mixer provides higher output power levels (to -58 dBm), improved suppression of undesired mixing products and higher rf impedances than did the single-junction mixers used in the previous device. Convolvers can provide the essential programmable matched-filter component for extremely wide-bandwidth spectral analysis or spread-spectrum communication systems. The current device has a 2-GHz design bandwidth and a time-bandwidth (TB) product of 28. It produced compressed pulses with -7 dB peak-to-side-lobe levels. Design improvements to be discussed include increasing the TB product to 100 and reducing spurious side-lobe levels.

IEEE Transactions on MagneticsMar 1, 198517 citations

Optically modulated superconducting delay lines

Elie K. Track, R.E. Drake, Gert K. G. Hohenwarter

Optical modulation is investigated for superconducting microstrip delay lines on 2-in-diameter, 10-mil-thick LaAlO/sub 3/ substrates. The linewidth of 80 mu m yields a characteristic impedance of 50 Omega . The linepitch of 100 mil is chosen to minimize the coupling between adjacent lines. The total meander line length is 64 cm. The measured delay is 8 ns with operation from DC to 20 GHz. The design was implemented using niobium, niobium nitride, and YBCO. The measurements were performed in a dewar and in a closed-cycle refrigerator, with both RF and optical access. Optical illumination of the lines resulted in a phase shift of the transmitted signal. Using a 10-mW He-Ne laser, phase shifts of up to 360 degrees at 20 GHz were measured with NbN and YBCO. The phase shifts increased linearly with frequency and with optically intensity. The effect can be attributed to a small, bolometric modulation of the line inductance.>

IEEE Transactions on Applied SuperconductivityMar 1, 199318 citations

Analog signal correlator using superconductive integrated components

J.B. Green, L. N. Smith, Alfredo C. Anderson +2 more

Analog superconductive components have been integrated to form a device capable of cross-correlation between wideband analog input signals. The device contains a tapped niobium delay line, tunnel-junction mixers, a lumped-element L-C resonator, and a tunnel-junction comparator. The tapped delay line is realized by a niobium stripline folded in a meander pattern on a rectangular silicon substrate. An array of Nb/Nb2O5/Pb tunnel junctions acts as a mixer to form the product of delayed samples of two carrier-offset analog signals counterpropagating along the transmission line. The resultant mixer products from the junction arrays are integrated and stored in a high-Q (≈ 600) resonator consisting of a lumped-element L-C network, tuned to the offset frequency. The low-leakage capacitor dielectric is formed from electrolytically anodized niobium. A superconductive tunnel junction imbedded in the resonator circuit is operated as a variable-threshold comparator to detect the time-integrated current stored in the resonator. Performance results from such a time-integrating correlator are presented, along with a discussion of the important design issues as they relate to analog signal processing.

IEEE Transactions on MagneticsMar 1, 19877 citations

Analog signal correlator design and operation

J.B. Green, Manjul Bhushan

A superconductive tapped delay line, circuits comprising superconductor-insulator-superconductor (SIS) mixers, an L-C integrator, and a tunnel junction comparator, and superconductive digital address encoders have been integrated into a 14-channel analog signal correlator. This 25*38 mm circuit was fabricated using a Nb/Nb/sub 2/O/sub 3//Pb tunnel junction process. Preliminary testing of this device indicates the ability to process long duration, wideband waveforms with time-bandwidth products equal to 6000.

IEEE Transactions on MagneticsMar 1, 19911 citation