Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Faster recovery time of a hot-electron transition-edge sensor by use of normal metal heat-sinks

Brice Calkins, Adriana E. Lita, Anna E. Fox, Sae Woo Nam

Published Dec 12, 2011• 32 citations
Publisher

Abstract

Transition-edge sensor microcalorimeters with recovery times near 1 μs have become highly desirable in quantum science applications as near-infrared single-photon detectors with photon-number resolving capability. Previously, the recovery times of these devices could be decreased only by changing device material or modifying the superconducting-to-normal transition. We demonstrate a method for improving this speed that uses a normal-metal heat-sink. This demonstration with tungsten devices realizes a factor of 4 decrease in recovery time without significantly affecting energy resolution. Our approach may enable the creation of high-efficiency transition-edge sensors with decay times short enough to operate with 80 MHz pulsed single-photon sources.

DOI
10.1063/1.3659686

Related papers

Titanium TES based photon number resolving detectors with 1 MHz counting rate and 65% quantum efficiency

Daiji Fukuda, Go Fujii, Takayuki Numata +4 more

A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 2, 2008•11 citations

Performance of photon-number resolving transition-edge sensors with integrated 1550 nm resonant cavities

Danna Rosenberg, Adriana E. Lita, Aaron Miller +2 more

Many quantum-information applications require high-efficiency, low-noise, single-photon detectors that operate at visible and near-infrared wavelengths. The tunable superconducting critical temperature and anomalously low electron-phonon coupling of tungsten make it a suitable material for the fabrication of transition-edge sensors (TESs) that meet these requirements. The quantum efficiency of a typical tungsten TES detector, intrinsically around 15% at 1550 nm, can be increased by placing the tungsten detector in a resonant cavity, but the performance of a device embedded in a cavity has not been tested previously. We demonstrate that the presence of the cavity does not adversely affect the sensitivity or response time, and we report on the device characteristics of a new generation of tungsten TESs with greater than 80% quantum efficiency at 1550 nm.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•62 citations

Fast transition-edge sensors suitable for photonic quantum computing

Ruslan Hummatov, Adriana E. Lita, Tannaz Farrahi +8 more

Photon-number resolving transition-edge sensors (TESs) with near unity system detection efficiency enable novel approaches to quantum computing, for example, heralding robust Gottesman–Kitaev–Preskill qubit states. Increasing the speed of the detectors increases the rate at which these states can be heralded. In addition, depending on the details of the scheme, faster detectors can reduce the complexities of the hardware implementation. In previous work, we demonstrated that adding a small amount of gold between the tungsten film and silicon substrate can increase thermal conductance and reduce detector recovery time. In that study, the readout electronics imposed limitations on stable biasing conditions of the TES detector, and the TES could only be biased at higher than ideal values. In this report, we demonstrate the operation of the TES illuminated by a heavily attenuated pulsed laser running at 1 MHz repetition rate and examine the limits to adding gold to speed up device recovery times using a higher bandwidth readout system. The best performance was achieved by combining a 15×15μm2 tungsten TES with 5μm3 of gold, which resulted in a recovery time faster than 250 ns, with an energy resolution of 0.25 eV full-width at half maximum at 0.8 eV photon energy.

Journal of Applied Physics•Jun 16, 2023•26 citations

Nanosecond-scale timing jitter for single photon detection in transition edge sensors

Antı́a Lamas-Linares, Brice Calkins, Nathan A. Tomlin +5 more

Transition edge sensors (TES) have the highest reported efficiencies (>98%) for single photon detection in the visible and near infrared. Experiments in quantum information and foundations of physics that rely on this efficiency have started incorporating these detectors. However, their range of applicability has been hindered by slow operation both in recovery time and timing jitter. We show how a conventional tungsten-TES can be operated with jitter times of ≈4 ns, providing a practical simplification for experiments that rely on simultaneous high efficiency and low timing uncertainty, such as loophole free Bell inequalities and device independent quantum cryptography.

Applied Physics Letters•Jun 10, 2013•48 citations

Nanosecond-scale timing jitter in transition edge sensors at telecom and visible wavelengths

Antı́a Lamas-Linares, Brice Calkins, Nathan A. Tomlin +5 more

Transition edge sensors (TES) have the highest reported efficiencies (>98%) for detection of single photons in the visible and near infrared. Experiments in quantum information and foundations of physics that rely critically on this efficiency have started incorporating these detectors into con- ventional quantum optics setups. However, their range of applicability has been hindered by slow operation both in recovery time and timing jitter. We show here how a conventional tungsten-TES can be operated with jitter times of < 4 ns, well within the timing resolution necessary for MHz clocking of experiments, and providing an important practical simplification for experiments that rely on the simultaneous closing of both efficiency and locality loopholes.

arXiv:1209.5721•Sep 25, 2012•12 citations

Superconducting transition-edge sensors optimized for high-efficiency photon-number resolving detectors

Adriana E. Lita, Brice Calkins, Lenson A. Pellouchoud +2 more

Superconducting photon detectors have emerged as a powerful new option for detecting single photons. System detection efficiency that incorporates the quantum efficiency of the device and system losses is one of the most important single-photon detector performance metrics for quantum information applications. Superconducting transition-edge sensors (TESs) are microcalorimeters that have the ability of distinguishing single photons with negligible dark counts. In addition, TESs are capable of directly measuring the photon number in a pulse of light. We have achieved near-unity system detection efficiency with TESs at particular wavelengths in the near-infrared by using multilayer structures that enhance the absorption of light into the active device material. We describe the design of the multilayer structure enabling high detection efficiency TESs including issues and requirements for obtaining detection efficiency values higher than 99 %. We describe the device fabrication and finally, show recent results of devices optimized for high detection efficiency using the multilayer structure.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 20, 2010•51 citations
Transition-edge sensor microcalorimeters with recovery times near 1 μs have become highly desirable in quantum science applications as near-infrared single-photon detectors with photon-number resolving capability. Previously, the recovery times of these devices could be decreased only by changing device material or modifying the superconducting-to-normal transition. We demonstrate a method for improving this speed that uses a normal-metal heat-sink. This demonstration with tungsten devices realizes a factor of 4 decrease in recovery time without significantly affecting energy resolution. Our approach may enable the creation of high-efficiency transition-edge sensors with decay times short enough to operate with 80 MHz pulsed single-photon sources.
A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.
Many quantum-information applications require high-efficiency, low-noise, single-photon detectors that operate at visible and near-infrared wavelengths. The tunable superconducting critical temperature and anomalously low electron-phonon coupling of tungsten make it a suitable material for the fabrication of transition-edge sensors (TESs) that meet these requirements. The quantum efficiency of a typical tungsten TES detector, intrinsically around 15% at 1550 nm, can be increased by placing the tungsten detector in a resonant cavity, but the performance of a device embedded in a cavity has not been tested previously. We demonstrate that the presence of the cavity does not adversely affect the sensitivity or response time, and we report on the device characteristics of a new generation of tungsten TESs with greater than 80% quantum efficiency at 1550 nm.
Photon-number resolving transition-edge sensors (TESs) with near unity system detection efficiency enable novel approaches to quantum computing, for example, heralding robust Gottesman–Kitaev–Preskill qubit states. Increasing the speed of the detectors increases the rate at which these states can be heralded. In addition, depending on the details of the scheme, faster detectors can reduce the complexities of the hardware implementation. In previous work, we demonstrated that adding a small amount of gold between the tungsten film and silicon substrate can increase thermal conductance and reduce detector recovery time. In that study, the readout electronics imposed limitations on stable biasing conditions of the TES detector, and the TES could only be biased at higher than ideal values. In this report, we demonstrate the operation of the TES illuminated by a heavily attenuated pulsed laser running at 1 MHz repetition rate and examine the limits to adding gold to speed up device recovery times using a higher bandwidth readout system. The best performance was achieved by combining a 15×15μm2 tungsten TES with 5μm3 of gold, which resulted in a recovery time faster than 250 ns, with an energy resolution of 0.25 eV full-width at half maximum at 0.8 eV photon energy.
Transition edge sensors (TES) have the highest reported efficiencies (>98%) for single photon detection in the visible and near infrared. Experiments in quantum information and foundations of physics that rely on this efficiency have started incorporating these detectors. However, their range of applicability has been hindered by slow operation both in recovery time and timing jitter. We show how a conventional tungsten-TES can be operated with jitter times of ≈4 ns, providing a practical simplification for experiments that rely on simultaneous high efficiency and low timing uncertainty, such as loophole free Bell inequalities and device independent quantum cryptography.
Transition edge sensors (TES) have the highest reported efficiencies (>98%) for detection of single photons in the visible and near infrared. Experiments in quantum information and foundations of physics that rely critically on this efficiency have started incorporating these detectors into con- ventional quantum optics setups. However, their range of applicability has been hindered by slow operation both in recovery time and timing jitter. We show here how a conventional tungsten-TES can be operated with jitter times of < 4 ns, well within the timing resolution necessary for MHz clocking of experiments, and providing an important practical simplification for experiments that rely on the simultaneous closing of both efficiency and locality loopholes.
Superconducting photon detectors have emerged as a powerful new option for detecting single photons. System detection efficiency that incorporates the quantum efficiency of the device and system losses is one of the most important single-photon detector performance metrics for quantum information applications. Superconducting transition-edge sensors (TESs) are microcalorimeters that have the ability of distinguishing single photons with negligible dark counts. In addition, TESs are capable of directly measuring the photon number in a pulse of light. We have achieved near-unity system detection efficiency with TESs at particular wavelengths in the near-infrared by using multilayer structures that enhance the absorption of light into the active device material. We describe the design of the multilayer structure enabling high detection efficiency TESs including issues and requirements for obtaining detection efficiency values higher than 99 %. We describe the device fabrication and finally, show recent results of devices optimized for high detection efficiency using the multilayer structure.