Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Performance of photon-number resolving transition-edge sensors with integrated 1550 nm resonant cavities

Danna Rosenberg, Adriana E. Lita, Aaron Miller, Sae Woo Nam, Robert E. Schwall

Published Jun 1, 2005• 62 citations
Publisher

Abstract

Many quantum-information applications require high-efficiency, low-noise, single-photon detectors that operate at visible and near-infrared wavelengths. The tunable superconducting critical temperature and anomalously low electron-phonon coupling of tungsten make it a suitable material for the fabrication of transition-edge sensors (TESs) that meet these requirements. The quantum efficiency of a typical tungsten TES detector, intrinsically around 15% at 1550 nm, can be increased by placing the tungsten detector in a resonant cavity, but the performance of a device embedded in a cavity has not been tested previously. We demonstrate that the presence of the cavity does not adversely affect the sensitivity or response time, and we report on the device characteristics of a new generation of tungsten TESs with greater than 80% quantum efficiency at 1550 nm.

DOI
10.1109/tasc.2005.849925

Related papers

Counting near-infrared single-photons with 95% efficiency

Adriana E. Lita, Aaron Miller, Sae Woo Nam

Single-photon detectors operating at visible and near-infrared wavelengths with high detection efficiency and low noise are a requirement for many quantum-information applications. Superconducting transition-edge sensors (TESs) are capable of detecting visible and near-infrared light at the single-photon level and are capable of discriminating between one- and two-photon absorption events; however these capabilities place stringent design requirements on the TES heat capacity, thermometry, and optical detection efficiency. We describe the fabrication and evaluation of a fiber-coupled, photon-number-resolving TES detector optimized for absorption at 1550 and 1310 nm wavelengths. The measured system detection efficiency at 1556 nm is 95 % +/- 2 %, which to our knowledge is the highest system detection efficiency reported for a near-infrared single-photon detector.

Optics Express•Jan 1, 2008•733 citations

Superconducting transition-edge sensors optimized for high-efficiency photon-number resolving detectors

Adriana E. Lita, Brice Calkins, Lenson A. Pellouchoud +2 more

Superconducting photon detectors have emerged as a powerful new option for detecting single photons. System detection efficiency that incorporates the quantum efficiency of the device and system losses is one of the most important single-photon detector performance metrics for quantum information applications. Superconducting transition-edge sensors (TESs) are microcalorimeters that have the ability of distinguishing single photons with negligible dark counts. In addition, TESs are capable of directly measuring the photon number in a pulse of light. We have achieved near-unity system detection efficiency with TESs at particular wavelengths in the near-infrared by using multilayer structures that enhance the absorption of light into the active device material. We describe the design of the multilayer structure enabling high detection efficiency TESs including issues and requirements for obtaining detection efficiency values higher than 99 %. We describe the device fabrication and finally, show recent results of devices optimized for high detection efficiency using the multilayer structure.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 20, 2010•51 citations

Titanium TES based photon number resolving detectors with 1 MHz counting rate and 65% quantum efficiency

Daiji Fukuda, Go Fujii, Takayuki Numata +4 more

A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 2, 2008•11 citations

A TES single-photon detector demonstrating high-energy-resolution, high efficiency, and ultra-low dark counts near 0.9 T c

Peizhan Li, Wen Zhang, Zhi-Fa Feng +7 more

Transition-edge sensors (TESs) are among the most promising technologies for single-photon detection, offering high quantum efficiency, low dark count rates, and energy-resolving capabilities. However, optimal TES performance typically requires ultra-low temperatures below 100 mK, necessitating bulky dilution refrigerators or adiabatic demagnetization refrigerators, which limits their practical deployment. In this work, we demonstrate a titanium-based TES optimized for 1064 nm photon detection that achieves high performance at an elevated bath temperature of 220 mK—approximately 90% of its superconducting transition temperature, making it compatible with more compact sorption refrigerators. Through the integration of an optical cavity, a detailed complex impedance and noise characterization, and a systematic investigation of dark count sources, the detector achieves a system detection efficiency exceeding 97%, an energy resolution of 240 meV, and an intrinsic dark count rate as low as 2 × 10−4 cps. These findings significantly expand the applicability of TES single-photon detectors to practical photon-counting systems, such as quantum information and infrared astronomy.

APL Photonics•Dec 1, 2025•3 citations

Development of Titanium-Based Transition-Edge Single-Photon Detector

Wen Zhang, Yue Geng, Zheng Wang +7 more

Superconducting transition-edge sensors (TESs), working as single-photon detectors with high quantum efficiency, low dark count rate, and photon number resolving capability, have been successfully used in quantum information experiments as well as astronomical transient object observations. Aiming to achieve high count rate, we are developing titanium-based superconducting TES single-photon detectors with a critical temperature of ~300 mK. Ti-based TESs with active area from 10 × 10 μm to 40 × 40 μm are first fabricated on silicon substrate coated with SiOx. The fabricated TES devices show a thermal conductance scaling with the active area and an effective time constant of ~4 μs from pulsed laser diode illumination. In order to get high quantum efficiency, we further design and fabricate a 1550-nm optical cavity based on dielectric mirror and antireflection layer, and study its absorption with an IR spectrometer. Ti TES devices on the dielectric mirror are then fabricated and the superconducting transition is measured.

IEEE Transactions on Applied Superconductivity•Mar 19, 2019•19 citations

Development of transition-edge sensors with high detection efficiency and fast response time

Takeshi Jodoi, Tetsuya Tsuruta, Takahiro Kikuchi +4 more

This study developed transition-edge sensors (TESs), which can achieve high detection efficiency and fast response time through an optimized optical cavity design. Their suitability for optical quantum information processing was confirmed. Furthermore, we developed TESs with two different sensitive area sizes—8 × 7 ţm2, 12 × 11 ţm2—and systematically evaluated their performances. By employing a titanium (Ti)/gold (Au) bilayer with a relatively high transition temperature as the sensitive element, we achieved a fast total response time—defined as the sum of the rise and decay times—of ∼160 ns. Furthermore, the optical cavity structure—predicted by simulations to achieve a photon absorptance of 99.9% at 1550 nm—yielded measured system detection efficiencies of 94.7% ± 0.62% for the 8 × 7 ţm2 TES and 99.0% ± 0.60% for the 12 × 11 ţm2 TES. Photon response measurements indicate an energy resolution of 0.20 eV for the 8 × 7 ţm2 TES and 0.37 eV for the 12 × 11 ţm2 TES. These results establish that the proposed TESs are the fastest and most efficient devices reported to date. The proposed devices offer a high detection efficiency, high count rate, and accurate photon-number resolution. Therefore, they provide a breakthrough platform for scalable fault-tolerant quantum information processing and enable significant advances in experimental quantum optics.

APL Photonics•Jul 1, 2026•0 citations
Many quantum-information applications require high-efficiency, low-noise, single-photon detectors that operate at visible and near-infrared wavelengths. The tunable superconducting critical temperature and anomalously low electron-phonon coupling of tungsten make it a suitable material for the fabrication of transition-edge sensors (TESs) that meet these requirements. The quantum efficiency of a typical tungsten TES detector, intrinsically around 15% at 1550 nm, can be increased by placing the tungsten detector in a resonant cavity, but the performance of a device embedded in a cavity has not been tested previously. We demonstrate that the presence of the cavity does not adversely affect the sensitivity or response time, and we report on the device characteristics of a new generation of tungsten TESs with greater than 80% quantum efficiency at 1550 nm.
Single-photon detectors operating at visible and near-infrared wavelengths with high detection efficiency and low noise are a requirement for many quantum-information applications. Superconducting transition-edge sensors (TESs) are capable of detecting visible and near-infrared light at the single-photon level and are capable of discriminating between one- and two-photon absorption events; however these capabilities place stringent design requirements on the TES heat capacity, thermometry, and optical detection efficiency. We describe the fabrication and evaluation of a fiber-coupled, photon-number-resolving TES detector optimized for absorption at 1550 and 1310 nm wavelengths. The measured system detection efficiency at 1556 nm is 95 % +/- 2 %, which to our knowledge is the highest system detection efficiency reported for a near-infrared single-photon detector.
Superconducting photon detectors have emerged as a powerful new option for detecting single photons. System detection efficiency that incorporates the quantum efficiency of the device and system losses is one of the most important single-photon detector performance metrics for quantum information applications. Superconducting transition-edge sensors (TESs) are microcalorimeters that have the ability of distinguishing single photons with negligible dark counts. In addition, TESs are capable of directly measuring the photon number in a pulse of light. We have achieved near-unity system detection efficiency with TESs at particular wavelengths in the near-infrared by using multilayer structures that enhance the absorption of light into the active device material. We describe the design of the multilayer structure enabling high detection efficiency TESs including issues and requirements for obtaining detection efficiency values higher than 99 %. We describe the device fabrication and finally, show recent results of devices optimized for high detection efficiency using the multilayer structure.
A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.
Transition-edge sensors (TESs) are among the most promising technologies for single-photon detection, offering high quantum efficiency, low dark count rates, and energy-resolving capabilities. However, optimal TES performance typically requires ultra-low temperatures below 100 mK, necessitating bulky dilution refrigerators or adiabatic demagnetization refrigerators, which limits their practical deployment. In this work, we demonstrate a titanium-based TES optimized for 1064 nm photon detection that achieves high performance at an elevated bath temperature of 220 mK—approximately 90% of its superconducting transition temperature, making it compatible with more compact sorption refrigerators. Through the integration of an optical cavity, a detailed complex impedance and noise characterization, and a systematic investigation of dark count sources, the detector achieves a system detection efficiency exceeding 97%, an energy resolution of 240 meV, and an intrinsic dark count rate as low as 2 × 10−4 cps. These findings significantly expand the applicability of TES single-photon detectors to practical photon-counting systems, such as quantum information and infrared astronomy.
Superconducting transition-edge sensors (TESs), working as single-photon detectors with high quantum efficiency, low dark count rate, and photon number resolving capability, have been successfully used in quantum information experiments as well as astronomical transient object observations. Aiming to achieve high count rate, we are developing titanium-based superconducting TES single-photon detectors with a critical temperature of ~300 mK. Ti-based TESs with active area from 10 × 10 μm to 40 × 40 μm are first fabricated on silicon substrate coated with SiOx. The fabricated TES devices show a thermal conductance scaling with the active area and an effective time constant of ~4 μs from pulsed laser diode illumination. In order to get high quantum efficiency, we further design and fabricate a 1550-nm optical cavity based on dielectric mirror and antireflection layer, and study its absorption with an IR spectrometer. Ti TES devices on the dielectric mirror are then fabricated and the superconducting transition is measured.
This study developed transition-edge sensors (TESs), which can achieve high detection efficiency and fast response time through an optimized optical cavity design. Their suitability for optical quantum information processing was confirmed. Furthermore, we developed TESs with two different sensitive area sizes—8 × 7 ţm2, 12 × 11 ţm2—and systematically evaluated their performances. By employing a titanium (Ti)/gold (Au) bilayer with a relatively high transition temperature as the sensitive element, we achieved a fast total response time—defined as the sum of the rise and decay times—of ∼160 ns. Furthermore, the optical cavity structure—predicted by simulations to achieve a photon absorptance of 99.9% at 1550 nm—yielded measured system detection efficiencies of 94.7% ± 0.62% for the 8 × 7 ţm2 TES and 99.0% ± 0.60% for the 12 × 11 ţm2 TES. Photon response measurements indicate an energy resolution of 0.20 eV for the 8 × 7 ţm2 TES and 0.37 eV for the 12 × 11 ţm2 TES. These results establish that the proposed TESs are the fastest and most efficient devices reported to date. The proposed devices offer a high detection efficiency, high count rate, and accurate photon-number resolution. Therefore, they provide a breakthrough platform for scalable fault-tolerant quantum information processing and enable significant advances in experimental quantum optics.