Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

The thermocoax cable as the microwave frequency filter for single electron circuits

Alexander B Zorin

Published Aug 1, 1995• 186 citations
Publisher

Abstract

We have analyzed the possibility of using the resistive coaxial cable, Thermocoax(R) Philips as a microwave cryofilter for single electron experiments performed in a top-loading system dilution refrigerator. The biasing and signal lines made of this cable are assumed to link a single electron device kept at the lowest temperature Td to the rf filter having a temperature Tf of several kelvin. The attenuation in a wide frequency range has been calculated and it turned out that a 40-cm-long piece of this cable with an outer diameter of 0.5 mm could drastically reduce the effect of noise from the 50 Ω source anchored at Tf (below 25 K), making its effect comparable with the effect of the thermal fluctuations in the device for Td≊40 mK. The calculated attenuation is in reasonable agreement with the data measured at frequencies up to 18 GHz.

DOI
10.1063/1.1145385

Related papers

Development of Semi-Rigid Superconducting Coaxial Cables as Low-Pass Filters

A. Kushino, Soichi Kasai

We developed thin semi-rigid coaxial cables for use as readout noise filters in low temperature experiments. The cables reported here had an outer diameter of 0.86 mm, and consisted of a standard cupronickel (CuNi) alloy as a seamless outer conductor and polytetrafluoroethylene (PTFE) as a dielectric material. The inner conductor was superconducting niobium-titanium (NbTi) covered by a CuNi cladding layer with a thickness of 0, 13, or 38 μm. The thermal conductance and transmission properties for the cables were measured at cryogenic temperatures and compared to those for a conventional CuNi semi-rigid cable. Between 1.4 and 8.4 K, the thermal conductance was similar to that for the conventional cable because the contribution from the cladding was estimated to be small. On the other hand, measured at about 3 K, the attenuation at high frequency up to 10 GHz differed in that the cutoff frequency increased with decreasing CuNi cladding thickness. For a cladding thickness of 38 μm, the 3 dB cutoff frequency for a 1-m-long cable was 100 MHz, whereas for a cladding thickness of 13 μm, it was 500 MHz. This type of semi-rigid cable can, therefore, be used as a low-pass filter whose attenuation characteristics can be tailored by changing the thickness of the cladding layer.

IEEE Transactions on Applied Superconductivity•Dec 26, 2016•6 citations

Noise measurement system at electron temperature down to 20 mK with combinations of the low pass filters

Masayuki Hashisaka, Yoshiaki Yamauchi, Kensaku Chida +3 more

We developed a quantum noise measurement system in a dilution refrigerator by using three kinds of cryogenic low pass filters. One of them is a commercial low pass filter inserted into the noise measurement lines instead of the conventional powder filter, which assures well-defined circuit parameters necessary for the noise measurement at a finite frequency. We checked that this filter gives sufficiently large attenuation up to 20 GHz at room temperature, 77 and 4.2 K. The electron temperature of the mesoscopic device placed in the present system was confirmed to be down to around 20 mK by measuring the thermal noise of the device.

Review of Scientific Instruments•Sep 1, 2009•21 citations

Electron Thermometry

Joost van der Heijden

The performance and accuracy of quantum electronics is substantially degraded when the temperature of the electrons in the devices is too high. The electron temperature can be reduced with appropriate thermal anchoring and by filtering both the low frequency and radio frequency noise. Ultimately, for high performance filters the electron temperature can approach the phonon temperature (as measured by resistive thermometers) in a dilution refrigerator. In this application note, the method for measuring the electron temperature in a typical quantum electronics device using Coulomb blockade thermometry is described. This technique is applied to find the readily achievable electron temperature in the device when using the QFilter provided by QDevil. With our thermometry measurements, using a single GaAs/AlGaAs quantum dot in an optimized experimental setup, we determined an electron temperature of 28 $\pm$ 2 mK for a dilution refrigerator base temperature of 18 mK.

arXiv:2403.16305•Mar 24, 2024•3 citations

Cryogenic thermal modeling of microwave high density signaling

Naomi Raicu, Tom Hogan, Xian Wu +4 more

Abstract Superconducting quantum computers require microwave control lines running from room temperature to the mixing chamber of a dilution refrigerator. Adding more lines without preliminary thermal modeling to make predictions risks overwhelming the cooling power at each thermal stage. In this paper, we investigate the thermal load of SC-086/50-SCN-CN semi-rigid coaxial cable, which is commonly used for the control and readout lines of a superconducting quantum computer, as we increase the number of lines to a quantum processor. We investigate the makeup of the coaxial cables, verify the materials and dimensions, and experimentally measure the total thermal conductivity of a single cable as a function of the temperature from cryogenic to room temperature values. We also measure the cryogenic DC electrical resistance of the inner conductor as a function of temperature, allowing for the calculation of active thermal loads due to Ohmic heating. Fitting this data produces a numerical thermal conductivity function used to calculate the static heat loads due to thermal transfer within the wires resulting from a temperature gradient. The resistivity data is used to calculate active heat loads, and we use these fits in a cryogenic model of a superconducting quantum processor in a typical Bluefors XLD1000-SL dilution refrigerator, investigating how the thermal load increases with processor sizes ranging from 100 to 225 qubits. We conclude that the theoretical upper limit of the described architecture is approximately 200 qubits. However, including an engineering margin in the cooling power and the available space for microwave readout circuitry at the mixing chamber, the practical limit is approximately 140 qubits.

arXiv:2502.01945•EPJ Quantum Technology•Oct 30, 2025•17 citations

Miniature electrical filters for single electron devices

D. Vion, P.F. Orfila, P. Joyez +2 more

In experiments on single electron devices, the electromagnetic noise from parts of the apparatus at temperatures higher than that of the device can dramatically increase the tunnel rates out of the Coulomb-blocked state and therefore increase the device error rate. The electrical lines must therefore be filtered adequately. We derive simple expressions for calculating the required attenuation coefficient. We describe a wide-band miniature dissipative filter functioning at cryogenic temperatures. The effective thermalization of an experiment at 30 mK can be obtained by placing four of these filters in series at temperatures ranging from 4 K to 30 mK.

Journal of Applied Physics•Mar 15, 1995•93 citations

Engineering the microwave to infrared noise photon flux for superconducting quantum systems

Sergey Danilin, João Barbosa, Michael Farage +6 more

Electromagnetic filtering is essential for the coherent control, operation and readout of superconducting quantum circuits at milliKelvin temperatures. The suppression of spurious modes around transition frequencies of a few GHz is well understood and mainly achieved by on-chip and package considerations. Noise photons of higher frequencies - beyond the pair-breaking energies - cause decoherence and require spectral engineering before reaching the packaged quantum chip. The external wires that pass into the refrigerator and go down to the quantum circuit provide a direct path for these photons. This article contains quantitative analysis and experimental data for the noise photon flux through coaxial, filtered wiring. The attenuation of the coaxial cable at room temperature and the noise photon flux estimates for typical wiring configurations are provided. Compact cryogenic microwave low-pass filters with CR-110 and Esorb-230 absorptive dielectric fillings are presented along with experimental data at room and cryogenic temperatures up to 70 GHz. Filter cut-off frequencies between 1 to 10 GHz are set by the filter length, and the roll-off is material dependent. The relative dielectric permittivity and magnetic permeability for the Esorb-230 material in the pair-breaking frequency range of 75 to 110 GHz are measured, and the filter properties in this frequency range are calculated. The estimated dramatic suppression of the noise photon flux due to the filter proves its usefulness for experiments with superconducting quantum systems.

arXiv:2107.09331•EPJ Quantum Technology•Jan 15, 2022•31 citations
We have analyzed the possibility of using the resistive coaxial cable, Thermocoax(R) Philips as a microwave cryofilter for single electron experiments performed in a top-loading system dilution refrigerator. The biasing and signal lines made of this cable are assumed to link a single electron device kept at the lowest temperature Td to the rf filter having a temperature Tf of several kelvin. The attenuation in a wide frequency range has been calculated and it turned out that a 40-cm-long piece of this cable with an outer diameter of 0.5 mm could drastically reduce the effect of noise from the 50 Ω source anchored at Tf (below 25 K), making its effect comparable with the effect of the thermal fluctuations in the device for Td≊40 mK. The calculated attenuation is in reasonable agreement with the data measured at frequencies up to 18 GHz.
We developed thin semi-rigid coaxial cables for use as readout noise filters in low temperature experiments. The cables reported here had an outer diameter of 0.86 mm, and consisted of a standard cupronickel (CuNi) alloy as a seamless outer conductor and polytetrafluoroethylene (PTFE) as a dielectric material. The inner conductor was superconducting niobium-titanium (NbTi) covered by a CuNi cladding layer with a thickness of 0, 13, or 38 μm. The thermal conductance and transmission properties for the cables were measured at cryogenic temperatures and compared to those for a conventional CuNi semi-rigid cable. Between 1.4 and 8.4 K, the thermal conductance was similar to that for the conventional cable because the contribution from the cladding was estimated to be small. On the other hand, measured at about 3 K, the attenuation at high frequency up to 10 GHz differed in that the cutoff frequency increased with decreasing CuNi cladding thickness. For a cladding thickness of 38 μm, the 3 dB cutoff frequency for a 1-m-long cable was 100 MHz, whereas for a cladding thickness of 13 μm, it was 500 MHz. This type of semi-rigid cable can, therefore, be used as a low-pass filter whose attenuation characteristics can be tailored by changing the thickness of the cladding layer.
We developed a quantum noise measurement system in a dilution refrigerator by using three kinds of cryogenic low pass filters. One of them is a commercial low pass filter inserted into the noise measurement lines instead of the conventional powder filter, which assures well-defined circuit parameters necessary for the noise measurement at a finite frequency. We checked that this filter gives sufficiently large attenuation up to 20 GHz at room temperature, 77 and 4.2 K. The electron temperature of the mesoscopic device placed in the present system was confirmed to be down to around 20 mK by measuring the thermal noise of the device.
The performance and accuracy of quantum electronics is substantially degraded when the temperature of the electrons in the devices is too high. The electron temperature can be reduced with appropriate thermal anchoring and by filtering both the low frequency and radio frequency noise. Ultimately, for high performance filters the electron temperature can approach the phonon temperature (as measured by resistive thermometers) in a dilution refrigerator. In this application note, the method for measuring the electron temperature in a typical quantum electronics device using Coulomb blockade thermometry is described. This technique is applied to find the readily achievable electron temperature in the device when using the QFilter provided by QDevil. With our thermometry measurements, using a single GaAs/AlGaAs quantum dot in an optimized experimental setup, we determined an electron temperature of 28 ±\pm± 2 mK for a dilution refrigerator base temperature of 18 mK.
Abstract Superconducting quantum computers require microwave control lines running from room temperature to the mixing chamber of a dilution refrigerator. Adding more lines without preliminary thermal modeling to make predictions risks overwhelming the cooling power at each thermal stage. In this paper, we investigate the thermal load of SC-086/50-SCN-CN semi-rigid coaxial cable, which is commonly used for the control and readout lines of a superconducting quantum computer, as we increase the number of lines to a quantum processor. We investigate the makeup of the coaxial cables, verify the materials and dimensions, and experimentally measure the total thermal conductivity of a single cable as a function of the temperature from cryogenic to room temperature values. We also measure the cryogenic DC electrical resistance of the inner conductor as a function of temperature, allowing for the calculation of active thermal loads due to Ohmic heating. Fitting this data produces a numerical thermal conductivity function used to calculate the static heat loads due to thermal transfer within the wires resulting from a temperature gradient. The resistivity data is used to calculate active heat loads, and we use these fits in a cryogenic model of a superconducting quantum processor in a typical Bluefors XLD1000-SL dilution refrigerator, investigating how the thermal load increases with processor sizes ranging from 100 to 225 qubits. We conclude that the theoretical upper limit of the described architecture is approximately 200 qubits. However, including an engineering margin in the cooling power and the available space for microwave readout circuitry at the mixing chamber, the practical limit is approximately 140 qubits.
In experiments on single electron devices, the electromagnetic noise from parts of the apparatus at temperatures higher than that of the device can dramatically increase the tunnel rates out of the Coulomb-blocked state and therefore increase the device error rate. The electrical lines must therefore be filtered adequately. We derive simple expressions for calculating the required attenuation coefficient. We describe a wide-band miniature dissipative filter functioning at cryogenic temperatures. The effective thermalization of an experiment at 30 mK can be obtained by placing four of these filters in series at temperatures ranging from 4 K to 30 mK.
Electromagnetic filtering is essential for the coherent control, operation and readout of superconducting quantum circuits at milliKelvin temperatures. The suppression of spurious modes around transition frequencies of a few GHz is well understood and mainly achieved by on-chip and package considerations. Noise photons of higher frequencies - beyond the pair-breaking energies - cause decoherence and require spectral engineering before reaching the packaged quantum chip. The external wires that pass into the refrigerator and go down to the quantum circuit provide a direct path for these photons. This article contains quantitative analysis and experimental data for the noise photon flux through coaxial, filtered wiring. The attenuation of the coaxial cable at room temperature and the noise photon flux estimates for typical wiring configurations are provided. Compact cryogenic microwave low-pass filters with CR-110 and Esorb-230 absorptive dielectric fillings are presented along with experimental data at room and cryogenic temperatures up to 70 GHz. Filter cut-off frequencies between 1 to 10 GHz are set by the filter length, and the roll-off is material dependent. The relative dielectric permittivity and magnetic permeability for the Esorb-230 material in the pair-breaking frequency range of 75 to 110 GHz are measured, and the filter properties in this frequency range are calculated. The estimated dramatic suppression of the noise photon flux due to the filter proves its usefulness for experiments with superconducting quantum systems.