Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Use of SiGe bipolar transistors for cryogenic readout of SQUIDs

M. Kiviranta

Published Nov 13, 2006• 29 citations
Publisher

Abstract

We have measured characteristics and noise of four commercially available SiGe heterojunction bipolar transistors at 4.2 K. One device exhibits 75 pV Hz −1/2 white noise and a 1/ f noise corner of 20 kHz at 9 mW power dissipation, proving suitable for readout of SQUIDs immersed in liquid He. Another device exhibits 370 pV Hz −1/2 white noise and a 1/ f noise corner of 5 kHz at 50 µW dissipation, and still gives useable gain at 7 µW dissipation. This device is useful for SQUID multiplexers intended for closed-cycle refrigerators, in which the cooling power is limited. The achievable dissipation is even compatible for operation in the low-temperature stages of dilution refrigerators or ADRs. Furthermore, SiGe-based dc SQUID readout with 0.35 μΦ 0 Hz −1/2 flux noise was demonstrated. Applying negative flux feedback yielded a slew rate exceeding 50Φ 0 μs −1 .

DOI
10.1088/0953-2048/19/12/014

Related papers

Low-noise ultra-high-speed dc SQUID readout electronics

D. Drung, Colmar Hinnrichs, H.-J. Barthelmess

User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.

Superconductor Science and Technology•Feb 27, 2006•76 citations

Improved dc SQUID read-out electronics with low 1/f noise preamplifier

D. Drung

An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.

Review of Scientific Instruments•Nov 1, 1997•43 citations

A post-SQUID ac amplifier aimed for multiplexed detector readouts

M. Kiviranta, Antti Virtanen, Heikki Seppä +3 more

We have built a room temperature amplifier based on Si JFETs (junction field effect transistors) intended for ac-coupled SQUID (superconducting quantum interference device) readouts, such as in frequency-domain multiplexed transition-edge sensor systems. The amplifier operates at 5M Hzcentre frequency where it has the measured noise temperature of 27 K for a 60 � load, which includes the noise from the active termination and the room temperature transformer. When it was driven from a SQUID with an on-chip matching transformer, flux noise of 0.45 µ� 0 Hz −1/2 was obtained. Additionally, w ec onsider the potential o ft he recently introduced SiGe bipolar transistors for the same application. The dynamic range considerations for SQUID multiplexers, which require the use of an amplifier with a low noise temperature, are briefly discussed. (Some figures in this article are in colour only in the electronic version)

Superconductor Science and Technology•Mar 16, 2006•6 citations

Development of low-noise two-stage dc-SQUID for TES detector readout

Nan Li, Mengjie Song, Sixiao Hu +9 more

Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.

arXiv:2601.19565•Superconductor Science and Technology•Apr 1, 2026•0 citations

Study of Nb and NbN Resonators at 0.1 K for Low-Noise Microwave SQUID Multiplexers

Tomoya Irimatsugawa, Fuminori Hirayama, Hirotake Yamamori +8 more

The quality factors and noise performances of superconducting resonators play an important role in microwave SQUID multiplexer (MW-MUX). Since we develop microwave SQUID multiplexer for transition edge sensor arrays, the operation temperature is around 100 mK where the effects of two level system (TLS) can be significant. In this paper, we have investigated the electrode-material or wafer dependence of noise performance of MW-MUX by characterizing four types of resonators. Although the temperature dependence of resonance frequency and the power dependence of Qu show clear difference among the materials, frequency noises which contribute the readout noise of MW-MUX are similar. Theoretical model predicts that not TLS but other loss dominates Qu in the power region suitable for the low-noise operation of our MW-MUX. Further, the estimated flux noise calculated from the measured frequency noise and the conversion √ coefficient from frequency to flux were 1-5 (μΦ0/√Hz) @ 1 Hz, 0.2-0.8 (μΦ0/√Hz) @ 3 kHz. These results indicate the noise of our MW-MUX has small material dependence and the compatible low noise operation to typical dc SQUIDs would be possible. Therefore, the MW-MUX with our materials would not suffer from the low frequency noise due to TLS.

IEEE Transactions on Applied Superconductivity•Dec 9, 2016•4 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations
We have measured characteristics and noise of four commercially available SiGe heterojunction bipolar transistors at 4.2 K. One device exhibits 75 pV Hz −1/2 white noise and a 1/ f noise corner of 20 kHz at 9 mW power dissipation, proving suitable for readout of SQUIDs immersed in liquid He. Another device exhibits 370 pV Hz −1/2 white noise and a 1/ f noise corner of 5 kHz at 50 µW dissipation, and still gives useable gain at 7 µW dissipation. This device is useful for SQUID multiplexers intended for closed-cycle refrigerators, in which the cooling power is limited. The achievable dissipation is even compatible for operation in the low-temperature stages of dilution refrigerators or ADRs. Furthermore, SiGe-based dc SQUID readout with 0.35 μΦ 0 Hz −1/2 flux noise was demonstrated. Applying negative flux feedback yielded a slew rate exceeding 50Φ 0 μs −1 .
User-friendly ultra-high-speed readout electronics for dc superconducting quantum interference devices (SQUIDs) are presented. To maximize the system bandwidth, the SQUID is directly read out without flux modulation. A composite preamplifier is used consisting of a slow dc amplifier in parallel with a fast ac amplifier. In this way, excellent dc precision and a high amplifier bandwidth of 50 MHz are achieved, simultaneously. A virtual 50 Ω amplifier input resistance with negligible excess noise is realized by active shunting, i.e., by applying feedback from preamplifier output to input via a high resistance. The white voltage and current noise levels are 0.33 nV Hz −1 and 2.6 pA Hz −1/2 , respectively. The electronics is fully computer controlled via a microcontroller integrated into the flux-locked loop (FLL) board. Easy-to-use software makes the various electronic settings accessible. A wide bias voltage range of 1.3 mV enables the readout of series SQUID arrays. Furthermore, additional current sources allow the operation of two-stage SQUIDs or transition edge sensors. The electronics was tested using various SQUIDs with input inductances between 30 nH and 1.5 µH. Typically, the maximum FLL bandwidth was 20 MHz, which is close to the theoretical limit given by transmission line delay within the FLL. Slew rates of up to 4.6 Φ 0 µs −1 were achieved with series SQUID arrays. Current noise levels as low as 0.47 pA Hz −1/2 and coupled energy sensitivities between 90 h and 500 h were measured at 4.2 K, where h is the Planck constant. The noise did not degrade when the system bandwidth was increased to the maximum value of about 20 MHz. With a two-stage set-up, intrinsic white energy sensitivities of 30 h and 2.3 h were measured at 4.2 and 0.3 K, respectively.
An improved read-out electronics without flux modulation for dc superconducting quantum interference devices (dc SQUIDs) is presented where the preamplifier is directly coupled to the SQUID. Compared to our previous designs, the 1/f voltage and current noise levels of the preamplifier were reduced by about a factor of 4 (rms) by using bipolar matched transistors instead of operational amplifiers at the input. Three types of flux-locked-loop electronics were developed and successfully tested: a low-power (120 mW) version for large multichannel arrays, a high-speed version with a 15 MHz bandwidth and a very fast (300 ns) reset mode, and a low-noise (0.44 nV/Hz) version with a fast and precise bias reversal circuit. The flux-locked-loop electronics are compatible with each other, so that only one type of low-power (180 mW) control unit is required to operate them. All essential specifications of practical SQUID systems (noise, dynamic behavior, and temperature stability) were determined by using liquid-helium and liquid-nitrogen cooled SQUIDs, respectively.
We have built a room temperature amplifier based on Si JFETs (junction field effect transistors) intended for ac-coupled SQUID (superconducting quantum interference device) readouts, such as in frequency-domain multiplexed transition-edge sensor systems. The amplifier operates at 5M Hzcentre frequency where it has the measured noise temperature of 27 K for a 60 � load, which includes the noise from the active termination and the room temperature transformer. When it was driven from a SQUID with an on-chip matching transformer, flux noise of 0.45 µ� 0 Hz −1/2 was obtained. Additionally, w ec onsider the potential o ft he recently introduced SiGe bipolar transistors for the same application. The dynamic range considerations for SQUID multiplexers, which require the use of an amplifier with a low noise temperature, are briefly discussed. (Some figures in this article are in colour only in the electronic version)
Abstract Direct-current superconducting quantum interference devices (dc-SQUIDs) are one of the most sensitive magnetic detectors. These sensors are extensively used in the readout of superconducting transition edge sensors (TESs), which are used for the detection of weak signals. A cosmic microwave background (CMB) polarization telescope operating in 22–48 GHz is currently under developing. The TESs calorimeter of the telescope will be readout by a time-division multiplexer SQUID readout system. We develop a two-stage dc-SQUID amplifier circuit, comprising an input-stage SQUID with 4 SQUID cells and a series SQUID array with 100 SQUID cells. This configuration has been shown to achieve extremely high signal gain while effectively controlling system noise. We assess the system noise at 300 mK in an adiabatic demagnetization refrigerator. The measured magnetic flux noise of the two-stage SQUID circuit system is approximately 0.3 μ Φ 0 / Hz at 10 kHz. The current noise equivalent to the input coil of input SQUID is about 2.4 pA / Hz . This result meets the low-noise readout requirements of the CMB TES and other applications with TES detectors.
The quality factors and noise performances of superconducting resonators play an important role in microwave SQUID multiplexer (MW-MUX). Since we develop microwave SQUID multiplexer for transition edge sensor arrays, the operation temperature is around 100 mK where the effects of two level system (TLS) can be significant. In this paper, we have investigated the electrode-material or wafer dependence of noise performance of MW-MUX by characterizing four types of resonators. Although the temperature dependence of resonance frequency and the power dependence of Qu show clear difference among the materials, frequency noises which contribute the readout noise of MW-MUX are similar. Theoretical model predicts that not TLS but other loss dominates Qu in the power region suitable for the low-noise operation of our MW-MUX. Further, the estimated flux noise calculated from the measured frequency noise and the conversion √ coefficient from frequency to flux were 1-5 (μΦ0/√Hz) @ 1 Hz, 0.2-0.8 (μΦ0/√Hz) @ 3 kHz. These results indicate the noise of our MW-MUX has small material dependence and the compatible low noise operation to typical dc SQUIDs would be possible. Therefore, the MW-MUX with our materials would not suffer from the low frequency noise due to TLS.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.