Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Low-noise modular microsusceptometer using nearly quantum limited dc SQUIDs

D. D. Awschalom, James R. Rozen, M. B. Ketchen, W. J. Gallagher, Alan W. Kleinsasser, Robert L. Sandstrom, B. Bumble

Published Nov 21, 1988• 115 citations
Publisher

Abstract

A flexible combination of superconducting integrated circuits was used to construct a low-temperature magneto-optic microsusceptometer utilizing a dc superconducting quantum inteference device (SQUID) detector operating near the quantum limit (coupled energy sensitivity of 1.7ℏ). Miniature pick-up loop assemblies on transparent substrates were joined by superconducting interchip connections to a thin-film dc SQUID, which is in turn read out by a second dc SQUID connected to room-temperature electronics. Measurements on an 8.5-μm-diam titanium dot evaporated directly into the pick-up loop demonstrate a spin sensitivity of ∼103 spins/(Hz)1/2 at T=290 mK.

DOI
10.1063/1.100291

Related papers

Low-noise tunnel junction dc SQUID’s

Michael W. Cromar, P. Carelli

We present the results of an investigation of thin-film dc super conducting quantum interference device (SQUID’s) with very high energy resolution. The SQUID’s were fabricated using integrated-circuit techniques appropriate for superconducting devices. A weakly coupled SQUID with very low inductance (1 pH) had an intrinsic energy sensitivity 6×10−34 J/Hz = 0.9 h. A well-coupled SQUID (coupling constant α = 0.43) had an energy sensitivity referred to the input coil of 4.7×10−32 J/Hz = 71 h.

Applied Physics Letters•May 1, 1981•86 citations

Very low noise, tightly coupled, dc SQUID amplifiers

B. Muhlfelder, J. A. Beall, Michael W. Cromar +1 more

We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.

Applied Physics Letters•Oct 27, 1986•19 citations

Use of low-noise dc-SQUIDs in fundamental physics experiments

P. Carelli, Maria Gabriella Castellano, Roberto Leoni +1 more

The noise performance of dc-SQUIDs (Superconducting Quantum Interference Devices), which nowadays can reach values close to the quantum limit, makes them very attractive as amplifiers for experiments using low temperatures and demanding for extremely high sensitivity. After reviewing the working principle of the dc-SQUID, we describe a thin-film device with a new structure, which allowed us to reach an energy sensitivity of 5.5 h- at 0.9 K and a good coupling with a large input coil. At last we discuss some fundamental physics experiments which take advantage from the SQUID use.

Journal de Physique IV (Proceedings)•Jun 1, 1998•0 citations

Octagonal washer DC SQUIDs and integrated susceptometers fabricated in a planarized sub- mu m Nb-AlO/sub x/-Nb technology

M. B. Ketchen, Dale J. Pearson, Kevin G. Stawiasz +9 more

The authors have designed, fabricated, and measured a number of Nb-AlO/sub x/-Nb octagonal washer DC superconducting quantum interference devices (SQUIDs) and miniature DC SQUID susceptometers having minimum feature size down to 0.5 mu m. With SQUID inductance values on the order of 100 pH, typical noise performance is better than 1 mu Phi /sub 0// square root Hz. The small minimum feature size of input coils and pickup loop structures will facilitate tight coupling to a wide variety of systems ranging from submicron particles and structures to conventional approximately mu H input circuits. A single-washer SQUID with an 80-turn 0.5- mu m-linewidth, 630-nH input coil has user-friendly V- Phi (voltage-flux) curves and a coupled energy sensitivity of 20 h at 4.2 K. Susceptometers with pickup loops ranging from 20- mu m to 0.8- mu m across have very user-friendly V- Phi curves and a resolution of order 100 mu /sub B// square root Hz at 4.2 K for devices with the smallest loops.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•27 citations

Sensitivity enhancement of Quantum Design dc superconducting quantum interference devices in two-stage configuration

R. Mezzena, Andrea Vinante, P. Falferi +5 more

The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.

Review of Scientific Instruments•Sep 1, 2001•31 citations

Strongly coupled, low noise dc-SQUID amplifiers

J. Pleikies

The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.

•Apr 1, 2009•0 citations
A flexible combination of superconducting integrated circuits was used to construct a low-temperature magneto-optic microsusceptometer utilizing a dc superconducting quantum inteference device (SQUID) detector operating near the quantum limit (coupled energy sensitivity of 1.7ℏ). Miniature pick-up loop assemblies on transparent substrates were joined by superconducting interchip connections to a thin-film dc SQUID, which is in turn read out by a second dc SQUID connected to room-temperature electronics. Measurements on an 8.5-μm-diam titanium dot evaporated directly into the pick-up loop demonstrate a spin sensitivity of ∼103 spins/(Hz)1/2 at T=290 mK.
We present the results of an investigation of thin-film dc super conducting quantum interference device (SQUID’s) with very high energy resolution. The SQUID’s were fabricated using integrated-circuit techniques appropriate for superconducting devices. A weakly coupled SQUID with very low inductance (1 pH) had an intrinsic energy sensitivity 6×10−34 J/Hz = 0.9 h. A well-coupled SQUID (coupling constant α = 0.43) had an energy sensitivity referred to the input coil of 4.7×10−32 J/Hz = 71 h.
We have fabricated and tested thin film, niobium edge junction, double transformer, dc superconducting quantum interference devices (SQUID’s) that were stable under room-temperature storage and thermal cycling and that had very good noise performance. The input inductance, approximately 1.7 μH, was large enough to facilitate good matching to many experiments. When the SQUID was operated as a small-signal amplifier, the minimum detectable energy per unit bandwidth (Se) was 5×10−33 J/Hz at 100 kHz, referred to the SQUID loop (uncoupled). The minimum detectable energy per unit bandwidth was 1.8×10−31 J/Hz at 100 kHz, referred to the input coil. The SQUID’s had good characteristics for flux-locked operation since the small signal Se was low over a substantial range of bias current and magnetic flux. For operation in a flux-locked feedback circuit, Se was 6×10−32 J/Hz at 1 kHz.
The noise performance of dc-SQUIDs (Superconducting Quantum Interference Devices), which nowadays can reach values close to the quantum limit, makes them very attractive as amplifiers for experiments using low temperatures and demanding for extremely high sensitivity. After reviewing the working principle of the dc-SQUID, we describe a thin-film device with a new structure, which allowed us to reach an energy sensitivity of 5.5 h- at 0.9 K and a good coupling with a large input coil. At last we discuss some fundamental physics experiments which take advantage from the SQUID use.
The authors have designed, fabricated, and measured a number of Nb-AlO/sub x/-Nb octagonal washer DC superconducting quantum interference devices (SQUIDs) and miniature DC SQUID susceptometers having minimum feature size down to 0.5 mu m. With SQUID inductance values on the order of 100 pH, typical noise performance is better than 1 mu Phi /sub 0// square root Hz. The small minimum feature size of input coils and pickup loop structures will facilitate tight coupling to a wide variety of systems ranging from submicron particles and structures to conventional approximately mu H input circuits. A single-washer SQUID with an 80-turn 0.5- mu m-linewidth, 630-nH input coil has user-friendly V- Phi (voltage-flux) curves and a coupled energy sensitivity of 20 h at 4.2 K. Susceptometers with pickup loops ranging from 20- mu m to 0.8- mu m across have very user-friendly V- Phi curves and a resolution of order 100 mu /sub B// square root Hz at 4.2 K for devices with the smallest loops.>
The energy sensitivity of a direct current (dc) superconducting quantum interference device (SQUID) can be improved if it is operated in a two-stage configuration. Employing this technique, a commercial dc SQUID system was modified and made competitive with other sensors especially designed for very low noise applications. We report the noise measurements performed in the temperature range 4.2 K–25 mK. At 4.2 K, the coupled energy sensitivity obtained with the two-stage dc SQUID was approximately ten times better than with a conventional readout electronics. The noise energy decreases linearly until approximately 300 mK, in good agreement with theoretical previsions. At lower temperature the hot-electron effect produces a saturation and the best energy sensitivity measured with open input coil is 35 ℏ.
The dc Superconducting Quantum Interference Device (dc-SQUID) is one of the most sensitive magnetic field sensors available. In this thesis we concentrate on its application as an amplifier. In this configuration, an input circuit of interest can be connected by means of a coupling coil. The intended application of our developed low-Tc SQUID amplifiers is the readout of the first spherical gravitational wave antenna MiniGRAIL. Using small-signal analysis as well as numerical simulations, we study the achievable signal-to-noise ratio of such sensors in practical measurements. Published theories and studies could be extended. Some interesting points treated are the influence of the often used negative feedback (flux-locked loop), an altered input impedance of the SQUID amplifier and the influence of back-action noise, which directly affects the object of interest. The altered operation of the SQUID due to the presence of the input circuit is studied in numerical experiments. Another important issue, the influence of integrated input coils on the dynamics of SQUIDs, is investigated theoretically and experimentally. The performance of our developed sensors is compared to numerical simulations on detailed models. The results give insights into the behavior, design and usage of dc-SQUIDs with integrated coils. For a SQUID with input inductances of 1.5 μH we reached a good coupled energy sensitivity of about 170 ¯h in a dilution refrigerator. Furthermore, we investigated the hot-electron effect. This effect typically limits the sensitivity of superconducting electronics at sub-Kelvin bath temperatures due to a weakened electron-phonon coupling. We performed heating experiments on thin-film resistors which are similar to the shunt resistors of the Josephson junctions used in our sensors. The suppression of the hot-electron effect via electronic thermal transport to attached cooling fins is investigated both experimentally, theoretically and numerically. The numerical technique turns out to be a useful tool for the thermal design of superconducting electronics.