Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Detection of 110 GHz millimeter-wave signal using DyBaCuO step-edge junction

Y. Fukumoto, Ichiro Shigaki, H. Kajikawa, R. Ogawa, Y. Kawate

Published Mar 1, 1993• 9 citations
Publisher

Abstract

Millimeter-wave detection was investigated using a step-edge microbridge Josephson junction (SEJJ) fabricated by a sputter-deposited DyBaCuO thin film. The SEJJ exhibited a clear response to 110-GHz millimeter-wave irradiation, and Shapiro steps could be observed up to the seventh step. Harmonic mixing detection was successfully achieved using microwaves of 6 approximately 22 GHz as a local oscillation signal. The dependence of conversion efficiency ( eta ) on the harmonic number was expressed as eta varies as N/sup -3.3/. The detector was operative at temperatures up to 65 K, although the efficiency rapidly decreased above 50 K.>

DOI
10.1109/77.233559

Related papers

Millimeter-wave detection by YBaCuO step-edge microbridge Josephson junction

Yoshito Fukumoto, Rikuo Ogawa, Yoshio Kawate

Millimeter-wave detection was investigated using a step-edge microbridge Josephson junction fabricated by a YBaCuO thin film for both the video detection and harmonic mixing detection. Current–voltage (I–V) characteristics, which could be described by the resistively shunted junction (RSJ) model, were obtained up to 70 K with the IcR product of 150 μV at 70 K. The responsivity and noise equivalent input power were calculated as 2400 W/V and 4.4×10−14 W/√Hz, respectively, in the video detection assuming the RSJ model approximation. Clear dependence of the intermediate frequency output on the applied dc bias voltage was observed in the harmonic mixing detection with the harmonic numbers of 5–16, reflecting the change of dynamic resistance at the constant voltage steps induced by the local oscillation signal on the I–V curve. A minimum detection power of −59.4 dB m and a conversion efficiency (η) of −49.6 dB were obtained for the harmonic number (N) of 5 at 60 K. The relationship between the η and N was expressed as η∝N−2.2.

Journal of Applied Physics•Sep 1, 1993•13 citations

Microwave Heterodyne Mixing by Step-Edge Microbridge Josephson Junctions Using YBaCuO Thin Films

Yoshito Fukumoto, Hiroshi Kajikawa, Rikuo Ogawa +1 more

Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz~2.0 GHz was successfully obtained.

International Conference on Solid State Devices and Materials (SSDM)•Aug 28, 1991•0 citations

Microwave Heterodyne Mixing by Step-Edge Microbridge Josephson Junctions Using YBaCuO Thin Films

Yoshito Fukumoto, Hiroshi Kajikawa, Rikuo Ogawa +1 more

Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz∼2.0 GHz was successfully obtained.

Japanese Journal of Applied Physics•Dec 1, 1991•17 citations

Properties of Step-Edge Microbridge Josephson Junction Mixer Fabricated by YBaCuO Thin Film

Yoshito Fukumoto, Hiroshi Kajikawa, Rikuo Ogawa +1 more

The conversion efficiency and minimum detection power of a step-edge microbridge Josephson junction mixer (SEJJ mixer) were evaluated for both fundamental mixing and harmonic mixing. The SEJJ was fabricated by a YBaCuO thin film and all of the circuits inside the mixer were made from microstrip line circuits in order to reduce the microwave propagation losses. The conversion efficiencies (η) were -31 dB, -46 dB and -53 dB for fundamental mixing, second harmonic mixing and third harmonic mixing, respectively. The dependence of η on the harmonic number (N) was expressed as η\proptN -4.6 for N≦3. The minimum detection power (MDP) of -60 dBm (1.0 nW) was obtained in fundamental mixing, with a linear dynamic range of more than 40 dB.

Japanese Journal of Applied Physics•Sep 1, 1992•9 citations

Millimeter Wave Harmonic Mixing in Thin-Film YBa2Cu3O7-x Josephson Junctions

Yoshizumi Yasuoka, Takashi Nozue, Tsutomu Yamashita

Harmonic mixing characteristics in thin-film YBa2Cu3O7-x (YBCO) Josephson junctions fabricated using photolithography were examined at the liquid nitrogen temperature (77 K) using 94 GHz millimeter wave radiation. As a result, a mixing signal (IF output) was obtained up to the harmonic number of 55 in harmonic mixing using the local oscillation (LO) wave as the microwave. The output strongly depended on the power of the LO and signal waves, and on the Shapiro step spacing induced by the LO wave. The IF output decreased in proportion to N -2 in the lower harmonic number region. However, the rate of decrease increased with an increase in the harmonic number.

Japanese Journal of Applied Physics•Nov 1, 1999•2 citations

High T/sub c/ superconducting step-edge junctions and their properties in millimeter-wave band

Yijun Feng, L. Kang, X. B. Wang +8 more

Superconducting step-edge junctions were fabricated on step-edges in (100) LaAlO/sub 3/ substrates by sputter-deposited epitaxial YBaCuO and TlBaCaCuO thin films. The substrate steps were patterned by ion beam etching using metal film as a mask. The transport properties of the junctions were characterized by four-probe electrical measurements. The critical current-normal resistance product (I/sub c/R/sub N/) was larger than 0.2 mV (77 K) for most of the junctions. Clear Shapiro steps were observed in the current-voltage characteristics of the junctions with 36 GHz or 95 GHz millimeter-wave irradiation. The high frequency properties of these high T/sub c/ Josephson junctions showed that they were quite suitable for the Josephson harmonic mixer used in the digital phase locked millimeter and sub-millimeter wave sources.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•1 citation
Millimeter-wave detection was investigated using a step-edge microbridge Josephson junction (SEJJ) fabricated by a sputter-deposited DyBaCuO thin film. The SEJJ exhibited a clear response to 110-GHz millimeter-wave irradiation, and Shapiro steps could be observed up to the seventh step. Harmonic mixing detection was successfully achieved using microwaves of 6 approximately 22 GHz as a local oscillation signal. The dependence of conversion efficiency ( eta ) on the harmonic number was expressed as eta varies as N/sup -3.3/. The detector was operative at temperatures up to 65 K, although the efficiency rapidly decreased above 50 K.>
Millimeter-wave detection was investigated using a step-edge microbridge Josephson junction fabricated by a YBaCuO thin film for both the video detection and harmonic mixing detection. Current–voltage (I–V) characteristics, which could be described by the resistively shunted junction (RSJ) model, were obtained up to 70 K with the IcR product of 150 μV at 70 K. The responsivity and noise equivalent input power were calculated as 2400 W/V and 4.4×10−14 W/√Hz, respectively, in the video detection assuming the RSJ model approximation. Clear dependence of the intermediate frequency output on the applied dc bias voltage was observed in the harmonic mixing detection with the harmonic numbers of 5–16, reflecting the change of dynamic resistance at the constant voltage steps induced by the local oscillation signal on the I–V curve. A minimum detection power of −59.4 dB m and a conversion efficiency (η) of −49.6 dB were obtained for the harmonic number (N) of 5 at 60 K. The relationship between the η and N was expressed as η∝N−2.2.
Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz~2.0 GHz was successfully obtained.
Current-voltage characteristics and microwave mixing properties of step-edge microbridge Josephson junctions (SEJJs) made of YBaCuO thin films were systematically investigated. The step-edge was formed on the surface of a MgO(100) substrate employing the common photolithograph and wet-etching techniques. YBaCuO thin film was deposited by the off-axis sputtering method, and the microbridge junctions were fabricated so as to cross the step-edge. The SEJJs showed typical DC and AC characteristics which were explained by the resistively shunted junction (RSJ) model. Mixing experiments were carried out in the K-band microwave region. An intermediate frequency (IF) output with the frequency range of 20 MHz∼2.0 GHz was successfully obtained.
The conversion efficiency and minimum detection power of a step-edge microbridge Josephson junction mixer (SEJJ mixer) were evaluated for both fundamental mixing and harmonic mixing. The SEJJ was fabricated by a YBaCuO thin film and all of the circuits inside the mixer were made from microstrip line circuits in order to reduce the microwave propagation losses. The conversion efficiencies (η) were -31 dB, -46 dB and -53 dB for fundamental mixing, second harmonic mixing and third harmonic mixing, respectively. The dependence of η on the harmonic number (N) was expressed as η\proptN -4.6 for N≦3. The minimum detection power (MDP) of -60 dBm (1.0 nW) was obtained in fundamental mixing, with a linear dynamic range of more than 40 dB.
Harmonic mixing characteristics in thin-film YBa2Cu3O7-x (YBCO) Josephson junctions fabricated using photolithography were examined at the liquid nitrogen temperature (77 K) using 94 GHz millimeter wave radiation. As a result, a mixing signal (IF output) was obtained up to the harmonic number of 55 in harmonic mixing using the local oscillation (LO) wave as the microwave. The output strongly depended on the power of the LO and signal waves, and on the Shapiro step spacing induced by the LO wave. The IF output decreased in proportion to N -2 in the lower harmonic number region. However, the rate of decrease increased with an increase in the harmonic number.
Superconducting step-edge junctions were fabricated on step-edges in (100) LaAlO/sub 3/ substrates by sputter-deposited epitaxial YBaCuO and TlBaCaCuO thin films. The substrate steps were patterned by ion beam etching using metal film as a mask. The transport properties of the junctions were characterized by four-probe electrical measurements. The critical current-normal resistance product (I/sub c/R/sub N/) was larger than 0.2 mV (77 K) for most of the junctions. Clear Shapiro steps were observed in the current-voltage characteristics of the junctions with 36 GHz or 95 GHz millimeter-wave irradiation. The high frequency properties of these high T/sub c/ Josephson junctions showed that they were quite suitable for the Josephson harmonic mixer used in the digital phase locked millimeter and sub-millimeter wave sources.>