Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics E Scientific Instruments

Simple oven design for highly reactive metal beam applications

Luis Bañares, Ángel González Ureña

Published Dec 1, 1989• 6 citations
Publisher

Abstract

An oven design suitable for producing stable beams of highly reactive metals is reported. Its attraction is in its simplicity, low cost and versatility in molecular beam and atomic/molecular physics experiments involving highly reactive metals such as rubidium, caesium, etc. An application is described for the case of atomic caesium, where the metal is produced by the chemical reaction Ba(s)+CsCl(s) to BaCl(s)+Cs(v). One of the main advantages of the present design is the use of a thin-walled, stainless steel pipe, as crucible and heater simultaneously, which considerably simplifies its design. With respect to the experimental method, the simplicity in the loading, working and cleaning procedures compared with the use of pure metal should be noted.

DOI
10.1088/0022-3735/22/12/020

Related papers

Designing an Atomic Beam

Cyril Bernard Lucas

Generally lower temperatures of evaporation make most aspects of oven design easier than those discussed in Chapter 5 and included in this group are ovens for the production of beams of alkali metals and their salts. Some special techniques are, however, necessary to handle the alkali metals because of their reactivity with moist air, which increases with atomic number Z. One solution is to produce the beam by a reaction of stable substances in the oven and we begin the discussion of the alkali metals with those cases in Section 4.2. We then consider in Section 4.3 more conventional ovens where the material to be evaporated is loaded directly into the oven. In Section 4.4 we turn to the alkali halides, which have problems due to their corrosiveness in the liquid and vapour state. Ovens where an ampoule of material has to be broken are discussed in Section 4.5. Finally in this chapter we discuss recycling ovens, where material that is not formed into a useful beam is returned to the oven.

CRC Press eBooks•Nov 27, 2013•0 citations

Atomic oven with rapid thermal response for atom experiments

Weilong Huang, Congjun Zou, Feiyu Dong +3 more

Atomic oven generating controllable atomic beam flux plays a fundamental role in quantum gas experiments. Here, we report a new heater design that can heat up an high temperature atomic oven with fast thermal response. The new heater shows a heating rate improved by 7.65 times comparing to that of the conventional resistive heater while the crucible temperature can heated up to 1200K. With this oven, we generated a collimated ytterbium beam with flux exceeding $10^{14} \text{ atoms/s}$ at 823 K. We believe that our design offers a promising solution for shortening experimental dead time and improve the experiment efficiency in cold atom researches.

physics.atom-phCross-listedarXiv:2607.04393•Jul 7, 2026•0 citations

A compact and efficient strontium oven for laser-cooling experiments

M. Schioppo, N. Poli, M. Prevedelli +4 more

Here we describe a compact and efficient strontium oven well suited for laser-cooling experiments. Novel design solutions allowed us to produce a collimated strontium atomic beam with a flux of 1.0 × 10(13) s(-1) cm(-2) at the oven temperature of 450 °C, reached with an electrical power consumption of 36 W. The oven is based on a stainless-steel reservoir, filled with 6 g of metallic strontium, electrically heated in a vacuum environment by a tantalum wire threaded through an alumina multi-bore tube. The oven can be hosted in a standard DN40CF cube and has an estimated continuous operation lifetime of 10 years. This oven can be used for other alkali and alkaline earth metals with essentially no modifications.

arXiv:1209.5639•Review of Scientific Instruments•Oct 1, 2012•60 citations

Low divergence cold-wall oven for loading ion traps

Anand Prakash, Akhil Ayyadevara, E. Krishnakumar +1 more

We present a compact cold-wall oven that is simple to build and align for loading miniature ion traps with calcium ions. The cold-wall oven, which is a metal-loaded capillary heated only through a portion of its length by the passage of a current, is described and characterized. An atomic beam with a low divergence of 14 mrad is produced. We perform Doppler-sensitive, resonant fluorescence measurements on the atomic beam to characterize the oven's performance. The emission of atoms from the oven is seen within ∼70 s after turning on the oven at an electric power consumption of <10 W. The flow rate is measured to be 1.5 ± 0.2 × 109 atoms s-1 at a temperature of 702 ± 7 K. The entire oven assembly is mounted on a CF16 feedthrough. This design can be extended to other species for producing a collimated atomic beam.

Review of Scientific Instruments•Mar 1, 2024•3 citations

A simple atomic beam oven with a metal thermal break

Chetan Vishwakarma, Jay Mangaonkar, Kushal Patel +3 more

We report the design and construction of a simple, easy to machine high temperature oven for generating an atomic beam in laser cooling experiments. This design eliminates the problem of thermal isolation of the oven region from the rest of the vacuum system without using a glass or ceramic thermal break. This design simplifies the construction and operation of high temperature ovens for elements having low vapor pressure. We demonstrate the functionality of such a source for strontium (Sr) atoms. We generate a high flux of Sr atoms for use in laser cooling and trapping experiments. The optimization of the design of the metal thermal break is done using a finite element analysis.

arXiv:1810.09090•Review of Scientific Instruments•May 1, 2019•6 citations

Theory of Collimated Atomic Beam Formation

Cyril Bernard Lucas

If a beam is to be produced from a material that is solid or liquid at laboratory temperature, then it must be converted to a vapour in an oven before it passes through the beam-forming impedance. In the reviews mentioned in Section 1.2, the approach has usually been to give details of numerous designs. In this chapter, we discuss the general design principles, and then the next two chapters become more of a reference source for the evaporation of different substances. We thus include the experience of a large number of experimenters who have needed to heat a liquid or solid substance to form it into an atomic or molecular beam. If the material can be evaporated and raised to a temperature to give the required input pressure at the input to the impedance at a temperature less than about 1500 K, it is usual to describe the heating device as an oven. At higher temperatures, the device is usually called a furnace, but the distinction is not really necessary. Hence we will avoid the term except for thermal dissociation of a molecular species, discussed in Chapter 6, when very high temperatures are usually needed, so a furnace is a more appropriate term. For convenience we will also term a completely different approach, namely, the evaporation of the material by direct electron beam heating of the surface (Section 3.2.5) as an oven. ‘Crucible’ is used by many authors interchangeably with ‘oven,’ but it often implies a container for the material to be evaporated that is placed within a heated envelope.

CRC Press eBooks•Nov 27, 2013•0 citations
An oven design suitable for producing stable beams of highly reactive metals is reported. Its attraction is in its simplicity, low cost and versatility in molecular beam and atomic/molecular physics experiments involving highly reactive metals such as rubidium, caesium, etc. An application is described for the case of atomic caesium, where the metal is produced by the chemical reaction Ba(s)+CsCl(s) to BaCl(s)+Cs(v). One of the main advantages of the present design is the use of a thin-walled, stainless steel pipe, as crucible and heater simultaneously, which considerably simplifies its design. With respect to the experimental method, the simplicity in the loading, working and cleaning procedures compared with the use of pure metal should be noted.
Generally lower temperatures of evaporation make most aspects of oven design easier than those discussed in Chapter 5 and included in this group are ovens for the production of beams of alkali metals and their salts. Some special techniques are, however, necessary to handle the alkali metals because of their reactivity with moist air, which increases with atomic number Z. One solution is to produce the beam by a reaction of stable substances in the oven and we begin the discussion of the alkali metals with those cases in Section 4.2. We then consider in Section 4.3 more conventional ovens where the material to be evaporated is loaded directly into the oven. In Section 4.4 we turn to the alkali halides, which have problems due to their corrosiveness in the liquid and vapour state. Ovens where an ampoule of material has to be broken are discussed in Section 4.5. Finally in this chapter we discuss recycling ovens, where material that is not formed into a useful beam is returned to the oven.
Atomic oven generating controllable atomic beam flux plays a fundamental role in quantum gas experiments. Here, we report a new heater design that can heat up an high temperature atomic oven with fast thermal response. The new heater shows a heating rate improved by 7.65 times comparing to that of the conventional resistive heater while the crucible temperature can heated up to 1200K. With this oven, we generated a collimated ytterbium beam with flux exceeding 1014 atoms/s10^{14} \text{ atoms/s}1014 atoms/s at 823 K. We believe that our design offers a promising solution for shortening experimental dead time and improve the experiment efficiency in cold atom researches.
Here we describe a compact and efficient strontium oven well suited for laser-cooling experiments. Novel design solutions allowed us to produce a collimated strontium atomic beam with a flux of 1.0 × 10(13) s(-1) cm(-2) at the oven temperature of 450 °C, reached with an electrical power consumption of 36 W. The oven is based on a stainless-steel reservoir, filled with 6 g of metallic strontium, electrically heated in a vacuum environment by a tantalum wire threaded through an alumina multi-bore tube. The oven can be hosted in a standard DN40CF cube and has an estimated continuous operation lifetime of 10 years. This oven can be used for other alkali and alkaline earth metals with essentially no modifications.
We present a compact cold-wall oven that is simple to build and align for loading miniature ion traps with calcium ions. The cold-wall oven, which is a metal-loaded capillary heated only through a portion of its length by the passage of a current, is described and characterized. An atomic beam with a low divergence of 14 mrad is produced. We perform Doppler-sensitive, resonant fluorescence measurements on the atomic beam to characterize the oven's performance. The emission of atoms from the oven is seen within ∼70 s after turning on the oven at an electric power consumption of <10 W. The flow rate is measured to be 1.5 ± 0.2 × 109 atoms s-1 at a temperature of 702 ± 7 K. The entire oven assembly is mounted on a CF16 feedthrough. This design can be extended to other species for producing a collimated atomic beam.
We report the design and construction of a simple, easy to machine high temperature oven for generating an atomic beam in laser cooling experiments. This design eliminates the problem of thermal isolation of the oven region from the rest of the vacuum system without using a glass or ceramic thermal break. This design simplifies the construction and operation of high temperature ovens for elements having low vapor pressure. We demonstrate the functionality of such a source for strontium (Sr) atoms. We generate a high flux of Sr atoms for use in laser cooling and trapping experiments. The optimization of the design of the metal thermal break is done using a finite element analysis.
If a beam is to be produced from a material that is solid or liquid at laboratory temperature, then it must be converted to a vapour in an oven before it passes through the beam-forming impedance. In the reviews mentioned in Section 1.2, the approach has usually been to give details of numerous designs. In this chapter, we discuss the general design principles, and then the next two chapters become more of a reference source for the evaporation of different substances. We thus include the experience of a large number of experimenters who have needed to heat a liquid or solid substance to form it into an atomic or molecular beam. If the material can be evaporated and raised to a temperature to give the required input pressure at the input to the impedance at a temperature less than about 1500 K, it is usual to describe the heating device as an oven. At higher temperatures, the device is usually called a furnace, but the distinction is not really necessary. Hence we will avoid the term except for thermal dissociation of a molecular species, discussed in Chapter 6, when very high temperatures are usually needed, so a furnace is a more appropriate term. For convenience we will also term a completely different approach, namely, the evaporation of the material by direct electron beam heating of the surface (Section 3.2.5) as an oven. ‘Crucible’ is used by many authors interchangeably with ‘oven,’ but it often implies a container for the material to be evaporated that is placed within a heated envelope.