Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Review of Scientific Instruments

Low divergence cold-wall oven for loading ion traps

Anand Prakash, Akhil Ayyadevara, E. Krishnakumar, S. A. Rangwala

Published Mar 1, 2024• 3 citations
Publisher

Abstract

We present a compact cold-wall oven that is simple to build and align for loading miniature ion traps with calcium ions. The cold-wall oven, which is a metal-loaded capillary heated only through a portion of its length by the passage of a current, is described and characterized. An atomic beam with a low divergence of 14 mrad is produced. We perform Doppler-sensitive, resonant fluorescence measurements on the atomic beam to characterize the oven's performance. The emission of atoms from the oven is seen within ∼70 s after turning on the oven at an electric power consumption of <10 W. The flow rate is measured to be 1.5 ± 0.2 × 109 atoms s-1 at a temperature of 702 ± 7 K. The entire oven assembly is mounted on a CF16 feedthrough. This design can be extended to other species for producing a collimated atomic beam.

DOI
10.1063/5.0190629

Related papers

Atomic flux distribution from a low-divergent dark wall oven

Lakhi Sharma, Atish Roy, Subhasis Panja +1 more

Nearly collimated atomic beam is of interest for a variety of experiments. This article reports a simple way of modifying the atomic beam distribution using a dark wall oven and describes detailed study of outcoming atoms’ spatial distribution. A simple design is obtained by employing the fact that inhomogeneous thermal distribution along a capillary results due to its partial resistive heating. Based on this phenomenon, we have designed a dark wall oven consisting of a reservoir, collimator, and cold absorber at the exit end of atoms, where all three are fabricated out of a single stainless steel capillary. The nearly collimated spatial distribution of the atoms resulting due to the absorber eliminating the atoms diverging above a certain angle is modeled and experimentally verified. A divergence as minimum as 1.2(1)° corresponding to a half angle θ1/2 = 0.9(1)° is measured at an oven temperature of 250 °C that produces an atomic flux of about 8 × 109 atoms s−1. Total flux as estimated using our measured spatial distribution of atoms matches well with the numerically simulated values of it for the dark wall oven.

Review of Scientific Instruments•May 1, 2019•12 citations

An optically heated atomic source for compact ion trap vacuum systems

Shaobo Gao, William J. Hughes, D. M. Lucas +2 more

We present a design for an atomic oven suitable for loading ion traps, which is operated via optical heating with a continuous-wave multimode diode laser. The absence of the low-resistance electrical connections necessary for Joule heating allows the oven to be extremely well thermally isolated from the rest of the vacuum system. Extrapolating from high-flux measurements of an oven filled with calcium, we calculate that a target region number density of 100 cm−3, suitable for rapid ion loading, will be produced with 175(10) mW of heating laser power, limited by radiative losses. With simple feedforward to the laser power, the turn-on time for the oven is 15 s. Our measurements indicate that an oven volume 1000 times smaller could still hold enough source metal for decades of continuous operation.

arXiv:2010.15497•Review of Scientific Instruments•Mar 1, 2021•0 citations

Rapid all-optical loading of trapped ions using a miniaturised atom source

Lorenzo Versini, Tim F. Wohlers-Reichel, Catherine E. J. Challoner +8 more

We characterise an efficient optically-heated neutral atom source for ion trapping. We observe loading rates of up to $24(3)\,\mathrm{s}^{-1}$ with heating powers below $85\,\mathrm{mW}$, and demonstrate loading of a single ion in under $30\,\mathrm{s}$ with $41.4(4)\,\mathrm{mW}$ of optical power in a room-temperature ion trap system with an ionisation probability of $1.50(5)\times10^{-5}$. We calibrate a thermal model for the source's internal temperature by imaging the fluorescence of a collimated flux of neutral calcium that effuses from the oven at various optical heating powers. We show that the thermal performance of this oven is mainly limited by radiative losses. We explore the effect of second-stage photo-ionisation laser power on the loading rate, and identify a path beyond the loading rates reported in this study. We predict that this source is also well-suited to a wide range of metals used in ion-trapping.

physics.atom-phCross-listedarXiv:2512.10514•Physical Review Applied•Dec 12, 2025•0 citations

A compact and efficient strontium oven for laser-cooling experiments

M. Schioppo, N. Poli, M. Prevedelli +4 more

Here we describe a compact and efficient strontium oven well suited for laser-cooling experiments. Novel design solutions allowed us to produce a collimated strontium atomic beam with a flux of 1.0 × 10(13) s(-1) cm(-2) at the oven temperature of 450 °C, reached with an electrical power consumption of 36 W. The oven is based on a stainless-steel reservoir, filled with 6 g of metallic strontium, electrically heated in a vacuum environment by a tantalum wire threaded through an alumina multi-bore tube. The oven can be hosted in a standard DN40CF cube and has an estimated continuous operation lifetime of 10 years. This oven can be used for other alkali and alkaline earth metals with essentially no modifications.

arXiv:1209.5639•Review of Scientific Instruments•Oct 1, 2012•60 citations

Low-power microstructured atomic oven for alkaline-earth-like elements

Julian Pick, J. Voß, Simon Hirt +4 more

Alkaline-earth-like elements play pivotal roles in advanced quantum sensing technologies, notably optical clocks, with unprecedented precision achieved in recent years. Despite remarkable progress, current optical-lattice clocks still face challenges in meeting the demanding size, weight, and power consumption constraints essential for space applications. Conventional atom sources, such as ovens or dispensers, require substantial heating power, which makes up a significant fraction of the overall power consumption of the system. Addressing this challenge, we present a microstructured atomic oven based on fused silica, designed for miniaturization and low-power operation. We characterize the oven by loading a magneto-optical trap with Yb evaporated from the oven and demonstrate operation with a loading rate above 10 8 atoms / s for heating powers below 250 mW.

arXiv:2408.12471•Physical Review Applied•Jan 8, 2025•5 citations

Design and characterization of an atomic beam source with narrow angular divergence for alkali-earth targets

Andrew James Murray, Martyn Hussey, Michael Needham

A new atomic beam source for use in laser-based experiments is described and characterized. The physically collimated source which has been tested using calcium, produces an atomic beam with low angular divergence and narrow transverse Doppler profile, as measured using fluorescence techniques with a near resonant laser beam. The low angular divergence of the source is essential for new experiments which study super-elastic scattering of electrons from laser prepared targets within a magnetic field, since the atomic beam must pass through a narrow gap between the coil windings. The beam density for calcium is calculated to be 2.8 × 109 atoms cm-3 when the source is operated at a temperature of 1090 K. This is sufficient to produce good electron energy loss and super-elastic scattering signals, while ensuring negligible radiation trapping within the atomic beam. © 2006 IOP Publishing Ltd.

Measurement Science and Technology•Oct 19, 2006•16 citations
We present a compact cold-wall oven that is simple to build and align for loading miniature ion traps with calcium ions. The cold-wall oven, which is a metal-loaded capillary heated only through a portion of its length by the passage of a current, is described and characterized. An atomic beam with a low divergence of 14 mrad is produced. We perform Doppler-sensitive, resonant fluorescence measurements on the atomic beam to characterize the oven's performance. The emission of atoms from the oven is seen within ∼70 s after turning on the oven at an electric power consumption of <10 W. The flow rate is measured to be 1.5 ± 0.2 × 109 atoms s-1 at a temperature of 702 ± 7 K. The entire oven assembly is mounted on a CF16 feedthrough. This design can be extended to other species for producing a collimated atomic beam.
Nearly collimated atomic beam is of interest for a variety of experiments. This article reports a simple way of modifying the atomic beam distribution using a dark wall oven and describes detailed study of outcoming atoms’ spatial distribution. A simple design is obtained by employing the fact that inhomogeneous thermal distribution along a capillary results due to its partial resistive heating. Based on this phenomenon, we have designed a dark wall oven consisting of a reservoir, collimator, and cold absorber at the exit end of atoms, where all three are fabricated out of a single stainless steel capillary. The nearly collimated spatial distribution of the atoms resulting due to the absorber eliminating the atoms diverging above a certain angle is modeled and experimentally verified. A divergence as minimum as 1.2(1)° corresponding to a half angle θ1/2 = 0.9(1)° is measured at an oven temperature of 250 °C that produces an atomic flux of about 8 × 109 atoms s−1. Total flux as estimated using our measured spatial distribution of atoms matches well with the numerically simulated values of it for the dark wall oven.
We present a design for an atomic oven suitable for loading ion traps, which is operated via optical heating with a continuous-wave multimode diode laser. The absence of the low-resistance electrical connections necessary for Joule heating allows the oven to be extremely well thermally isolated from the rest of the vacuum system. Extrapolating from high-flux measurements of an oven filled with calcium, we calculate that a target region number density of 100 cm−3, suitable for rapid ion loading, will be produced with 175(10) mW of heating laser power, limited by radiative losses. With simple feedforward to the laser power, the turn-on time for the oven is 15 s. Our measurements indicate that an oven volume 1000 times smaller could still hold enough source metal for decades of continuous operation.
We characterise an efficient optically-heated neutral atom source for ion trapping. We observe loading rates of up to 24(3) s−124(3)\,\mathrm{s}^{-1}24(3)s−1 with heating powers below 85 mW85\,\mathrm{mW}85mW, and demonstrate loading of a single ion in under 30 s30\,\mathrm{s}30s with 41.4(4) mW41.4(4)\,\mathrm{mW}41.4(4)mW of optical power in a room-temperature ion trap system with an ionisation probability of 1.50(5)×10−51.50(5)\times10^{-5}1.50(5)×10−5. We calibrate a thermal model for the source's internal temperature by imaging the fluorescence of a collimated flux of neutral calcium that effuses from the oven at various optical heating powers. We show that the thermal performance of this oven is mainly limited by radiative losses. We explore the effect of second-stage photo-ionisation laser power on the loading rate, and identify a path beyond the loading rates reported in this study. We predict that this source is also well-suited to a wide range of metals used in ion-trapping.
Here we describe a compact and efficient strontium oven well suited for laser-cooling experiments. Novel design solutions allowed us to produce a collimated strontium atomic beam with a flux of 1.0 × 10(13) s(-1) cm(-2) at the oven temperature of 450 °C, reached with an electrical power consumption of 36 W. The oven is based on a stainless-steel reservoir, filled with 6 g of metallic strontium, electrically heated in a vacuum environment by a tantalum wire threaded through an alumina multi-bore tube. The oven can be hosted in a standard DN40CF cube and has an estimated continuous operation lifetime of 10 years. This oven can be used for other alkali and alkaline earth metals with essentially no modifications.
Alkaline-earth-like elements play pivotal roles in advanced quantum sensing technologies, notably optical clocks, with unprecedented precision achieved in recent years. Despite remarkable progress, current optical-lattice clocks still face challenges in meeting the demanding size, weight, and power consumption constraints essential for space applications. Conventional atom sources, such as ovens or dispensers, require substantial heating power, which makes up a significant fraction of the overall power consumption of the system. Addressing this challenge, we present a microstructured atomic oven based on fused silica, designed for miniaturization and low-power operation. We characterize the oven by loading a magneto-optical trap with Yb evaporated from the oven and demonstrate operation with a loading rate above 10 8 atoms / s for heating powers below 250 mW.
A new atomic beam source for use in laser-based experiments is described and characterized. The physically collimated source which has been tested using calcium, produces an atomic beam with low angular divergence and narrow transverse Doppler profile, as measured using fluorescence techniques with a near resonant laser beam. The low angular divergence of the source is essential for new experiments which study super-elastic scattering of electrons from laser prepared targets within a magnetic field, since the atomic beam must pass through a narrow gap between the coil windings. The beam density for calcium is calculated to be 2.8 × 109 atoms cm-3 when the source is operated at a temperature of 1090 K. This is sufficient to produce good electron energy loss and super-elastic scattering signals, while ensuring negligible radiation trapping within the atomic beam. © 2006 IOP Publishing Ltd.