Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Quantum Electronics and Laser Science Conference

Optical bistability in reflection-mode operation of a diode laser amplifier

Donald M. Wood, Gautam Vemuri

Published Jun 7, 1996• 0 citations
OpenAlex

Abstract

Summary form only given. We report results of an experiment in which the output of a single-mode diode laser is injected into a diode laser amplifier operated close to its lasing threshold. The injected light is periodically modulated at frequencies very slow compared with the relevant relaxation frequencies within the amplifier. In contrast to most experiments, we operate the amplifier in a reflection mode instead of the transmission mode. Under the influence of the periodic modulation, the amplifier output exhibits several novel types of hysteresis and associated bistable behavior.

Related papers

Reflective bistability in 1.55 μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.

•Jan 1, 1998•0 citations

Optical bistability and X-shaped hysteresis in laser diode amplifiers

N. F. Mitchell, James O’Gorman, John Hegarty +1 more

Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>

IEEE Lasers and Electro-Optics Society Annual Meeting (LEOS)•Dec 30, 2002•4 citations

Measurements and modeling of reflective bistability in 1.55-μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.

IEEE Journal of Quantum Electronics•Jan 1, 1999•44 citations

Optical bistability in asymmetric Fabry–Perot laser-diode amplifiers

N. F. Mitchell, John C. Connolly, James O’Gorman +1 more

We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.

Optics Letters•Feb 15, 1994•28 citations

Demonstration Of Cascadability And Spectral Bistability In Bistable Diode Laser Amplifiers

Zeqi Pan, T. N. Ding, M. Dagenais

We report the demonstration of cascadability in bistable diode laser amplifiers operated below threshold. A schematic of the experimental set-up is shown in Figure 1. There it is shown that the optical input to the first bistable diode laser amplifier is modulated by a mechanical chopper at frequency Ω1. The output from the first bistable diode laser amplifier is then modulated at Ω2= 2Ω1using a second mechanical chopper. The light is thereafter used as the input to the second bistable device. When the input intensity to the second device is higher than a certain threshold, the output switches. These results are shown in Figure 2. For these experiments, each of the bistable diode laser amplifiers were carefully studied. Detailed bistability measurements at different bias currents and different cavity detuning's were performed. It was found that both the bistability loop and the switching power gets larger as the detuning increases. The size of the hysteresis loop also increased as the laser was operated closer to threshold. In a two beam experiment, it was found that the switching power in the data beam can be as small as 25 nW. Gains larger than 1000 have been demonstrated, indicating the large fan-out capability of these devices. The turn-on and turn-off times in these bistable diode laser amplifiers was measured to be faster than 1 ns and detector limited. These bistable diode laser amplifiers are the most efficient optical devices that have yet been demonstrated and will find applications in photonic switching networks.

Digest on Nonlinear Optics: Materials, Phenomena and Devices•Jan 1, 1990•0 citations

Optical bistability in diode-laser amplifiers and injection-locked laser diodes

Rongqing Hui, Sergio Benedetto, Ivo Montrosset

Static and dynamic properties of dispersive optical bistability (OB) in semiconductor lasers biased from below to above threshold have been investigated theoretically. The OB result is found to be varied continuously from below to above threshold with its maximum value located just above threshold; this result has been verified experimentally. A much faster switch-off of OB can be expected when the laser operates in the injection-locked condition.

Optics Letters•Feb 15, 1993•18 citations
Summary form only given. We report results of an experiment in which the output of a single-mode diode laser is injected into a diode laser amplifier operated close to its lasing threshold. The injected light is periodically modulated at frequencies very slow compared with the relevant relaxation frequencies within the amplifier. In contrast to most experiments, we operate the amplifier in a reflection mode instead of the transmission mode. Under the influence of the periodic modulation, the amplifier output exhibits several novel types of hysteresis and associated bistable behavior.
Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.
Laser diode amplifiers exhibit optical bistability when biased just below lasing threshold, and have applications as optical memory elements and optical switches, due to their very low switching energy (fJ) and presence of optical gain. While LDAs operated in transmission have received much attention, the reflection mode of operation has been largely neglected. In this paper we present a detailed experimental and numerical investigation of Fabry Perot LDA (FP-LDA) behavior under light injection when operated in reflection. We observe transitions from anticlockwise to clockwise hysteresis with changing bias level or incident wavelength detuning. Moreover, we also report the first experimental observation of X-shaped (or butterfly hysteresis) in this system. Our results are in very good agreement with calculation.>
We present experimental measurements of bistable characteristics for the case of a 1.55-/spl mu/m symmetric Fabry-Perot laser amplifier with a particularly rich variety of behavior for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical output-input characteristic when the drive current or initial phase detuning is changed. A "butterfly" hysteresis loop is observed experimentally at an optical input power as low as 300 /spl mu/W for a drive current equal to 94% of the lasing threshold. The dependence of the reflective optical bistability on drive current, initial phase detuning, and injected optical pewter has been investigated for the first time in an uncoated 1.55-/spl mu/m amplifier. Measurements of the device voltage shifts on switching reveal hysteresis loops which match those in the corresponding optical powers and which indicate the amount of gain saturation and nonlinear refraction responsible for bistability. An analytical model is used to describe the observed reflective bistability and to give insight into the detailed physical mechanisms responsible.
We present what is to our knowledge the first study of optical bistability in Fabry-Perot laser-diode amplifiers that have asymmetric facet reflectivities. When operated in reflection, the light input-light output characteristics exhibit a transition from counterclockwise to clockwise hysteresis by way of an X-shaped or butterfly hysteresis. This transition can be achieved by a change in either the device bias or the phase detuning of the incident light. Our results are in good agreement with calculation.
We report the demonstration of cascadability in bistable diode laser amplifiers operated below threshold. A schematic of the experimental set-up is shown in Figure 1. There it is shown that the optical input to the first bistable diode laser amplifier is modulated by a mechanical chopper at frequency Ω1. The output from the first bistable diode laser amplifier is then modulated at Ω2= 2Ω1using a second mechanical chopper. The light is thereafter used as the input to the second bistable device. When the input intensity to the second device is higher than a certain threshold, the output switches. These results are shown in Figure 2. For these experiments, each of the bistable diode laser amplifiers were carefully studied. Detailed bistability measurements at different bias currents and different cavity detuning's were performed. It was found that both the bistability loop and the switching power gets larger as the detuning increases. The size of the hysteresis loop also increased as the laser was operated closer to threshold. In a two beam experiment, it was found that the switching power in the data beam can be as small as 25 nW. Gains larger than 1000 have been demonstrated, indicating the large fan-out capability of these devices. The turn-on and turn-off times in these bistable diode laser amplifiers was measured to be faster than 1 ns and detector limited. These bistable diode laser amplifiers are the most efficient optical devices that have yet been demonstrated and will find applications in photonic switching networks.