Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Higher levels of the transmon qubit

Samuel James Bader

Published Jan 1, 2014• 0 citations
OpenAlex

Abstract

This thesis discusses recent experimental work in measuring the properties of higher levels in transmon qubit systems. The first part includes a thorough overview of transmon devices, explaining the principles of the device design, the transmon Hamiltonian, and general Circuit Quantum Electrodynamics concepts and methodology. The second part discusses the experimental setup and methods employed in measuring the higher levels of these systems, and the details of the simulation used to explain and predict the properties of these levels.

Related papers

Scalability and modularity for transmon-based quantum processors

Christian Dickel

This thesis mainly summarizes two experiments that relate to building a quantum computer out of superconducting transmon qubits. Transmon qubits have emerged as one of the foremost solid state qubits, realizing processors with more than ten qubits and demonstrating small scale quantum algorithms as well as quantum error correction schemes. Right now, there is a race between different academic and industry research groups to scale up transmon qubit processors. The first experiment was a demonstration of qubit control by selective broadcasting in order to reduce the scaling of expensive electronics with the number of qubits for individual single-qubit control. We demonstrated that we can bring two transmon qubits to the same frequency (combining fabrication accuracy and in-situ fine tuning) and use the same hardware to control both, routing the pulses with a nanosecond-timescale vector switch matrix. Despite the compromises required by this technique, we show a scalable path to single qubit control beyond the threshold required for quantum error correction. In benchmarking, we take into account gate leakage due to the fact that transmons are fundamentally multi-level systems. In the second experiment we establish entanglement between two transmon qubits on different chips. We use an entanglement by measurement scheme and demonstrate that we can overcome minor fabrication imperfections by shaping our measurement pulses. Ultimately, performance is mainly limited by photon loss between the chips and up to the amplification chain. This entanglement mediated by traveling photons could be used to make a distributed transmon processor where computations are spread across several chip modules. This modularity could enable connectivities that cannot be realized on chip and ease fabrication requirements, as modules could be individually fabricated and selected. Thus, both of these experiments fit into the larger effort to converge on the hardware, control equipment and architecture of a future large-scale transmon quantum computer. Other experiments I contributed to are summarized in the conclusion chapter to show the diverse physics that can be studied in cQED experiments.

•Jan 1, 2018•2 citations

Microwave Circuit Analysis of Multi Transmon Qubit System

Jonathan Gnanadhas

The quest to design a realizable quantum computer is a dream for many for the past few decades. At the moment, one of the promising designs is the transmon qubit, which is a superconducting qubit is the focus of this work. In order to analyze and design different components of a quantum chip, an understanding of the circuitry is required. By varying the circuit parameters, one can design the system according to requirements by constructing the required physical geometry that incorporates the design parameters. In this thesis work, part of the focus was to understand the transmon qubit circuit parameters, extract the circuit parameters such as capacitances from a physical geometry, build analytic and numerical 3D FEM models. Using a circuit model of the qubit system, the interdependence of the resonators that connects qubits with each other can be studied. Their resonances play a role in the qubit Hamiltonian and can be estimated by constructing accurate simulation models. This problem statement has been dealt with in the thesis work by constructing a hybrid circuitry of standard circuit components and 3D FEM simulated qubit unit cells. The quality factor of the measurement readout resonator of a qubit system needs to be characterized in a qubit system in order to target the rate and resolution at which the measurements can be done. In order to do so, the circuit parameters that affect the quality factor needs to be investigated. This problem statement has also been treated in this work.

•Jan 1, 2018•0 citations

Investigation of Transmon Qubit Designs - A Study of Plasma Frequency Predictability

Philip Krantz

This master thesis was dedicated to design, fabricate, and characterize subsystems of superconducting transmon qubits. Especially, focus was on investigating the predictability of the plasma frequency of the transmon, from which its operational properties are govern. In turn, the plasma frequency is governed by the normal state resistance of the two Josephson junctions along with its total capacitance. In\nprevious experiments, this frequency predictability relied entirely upon successful simulations of the system. However, even small simulation errors prove to generate\nsevere consequences for the system and a better, more systematic control is desired.\nIn order to identify and minimize this uncertainty, subsystems of the transmon were isolated and investigated. Test structures were fabricated and used to measure the normal state resistance of tunnel junctions with different areas and oxidation parameters using a four-point probe setup. A regime within which the reproducibility is increased was statistically identified. The shunt capacitance, i.e. the largest contribution to the total capacitance, of transmons was extracted by coupling identical capacitors to resonators. The coupling capacitance of a resonator is related to its external quality factor which was measured from analyzing the reflected microwave signal at cryogenic temperatures.\nThe smallest standard deviation of normal state resistances for 110 junction pairs was measured for junctions with an area 2.37 um^2 to be 1.48%, corresponding to an uncertainty contribution of 2 MHz for a designed plasma frequency of 6 GHz. Six resonators were measured throughout the shunt capacitance experiment and a linear t was used to compare the results with a written model based on conformal mapping.

•Jan 1, 2010•2 citations

Fabrication and characterization of transmon qubits and rectangular waveguide resonators for circuit quantum electrodynamics

Dong-Gwang Ha, Jung Hwan Park, So-Yeon Jun +2 more

Bulletin of the American Physical Society•Mar 19, 2013•0 citations

A Tutorial for Characterizing Transmon Qubits

Alexandre M. Souza, Davi A. D. Chaves, Carmem M. Gilardoni +3 more

Superconducting transmon qubits are a leading technology for quantum information processing, yet their reliable operation rests on meticulous calibration and characterization routines. These processes have been fine-tuned and are relatively well understood by the quantum computing community. Nevertheless, it is often challenging for newcomers to compile all the available information into a practical experimental flow. In this tutorial, we present a comprehensive walkthrough for the characterization and optimization of tunable transmon qubits, demonstrated on a commercial five-qubit processor. Moving beyond theoretical description, we detail in a straightforward manner the complete workflow, from cryogenic setup and wiring to parametric amplifier optimum operation, flux sweet-spot identification, pulse calibration, and readout optimization. We also demonstrate the characterization of qubit-qubit coupling, covering all steps before multiqubit operations. This guide serves as a reference for experimentalists seeking to efficiently bring up transmon-based quantum devices.

quant-pharXiv:2606.03815•Jun 3, 2026•0 citations

Experiments on multi-level superconducting qubits and coaxial circuit QED

Michael Peterer

Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.

•Jan 1, 2016•1 citation
This thesis discusses recent experimental work in measuring the properties of higher levels in transmon qubit systems. The first part includes a thorough overview of transmon devices, explaining the principles of the device design, the transmon Hamiltonian, and general Circuit Quantum Electrodynamics concepts and methodology. The second part discusses the experimental setup and methods employed in measuring the higher levels of these systems, and the details of the simulation used to explain and predict the properties of these levels.
This thesis mainly summarizes two experiments that relate to building a quantum computer out of superconducting transmon qubits. Transmon qubits have emerged as one of the foremost solid state qubits, realizing processors with more than ten qubits and demonstrating small scale quantum algorithms as well as quantum error correction schemes. Right now, there is a race between different academic and industry research groups to scale up transmon qubit processors. The first experiment was a demonstration of qubit control by selective broadcasting in order to reduce the scaling of expensive electronics with the number of qubits for individual single-qubit control. We demonstrated that we can bring two transmon qubits to the same frequency (combining fabrication accuracy and in-situ fine tuning) and use the same hardware to control both, routing the pulses with a nanosecond-timescale vector switch matrix. Despite the compromises required by this technique, we show a scalable path to single qubit control beyond the threshold required for quantum error correction. In benchmarking, we take into account gate leakage due to the fact that transmons are fundamentally multi-level systems. In the second experiment we establish entanglement between two transmon qubits on different chips. We use an entanglement by measurement scheme and demonstrate that we can overcome minor fabrication imperfections by shaping our measurement pulses. Ultimately, performance is mainly limited by photon loss between the chips and up to the amplification chain. This entanglement mediated by traveling photons could be used to make a distributed transmon processor where computations are spread across several chip modules. This modularity could enable connectivities that cannot be realized on chip and ease fabrication requirements, as modules could be individually fabricated and selected. Thus, both of these experiments fit into the larger effort to converge on the hardware, control equipment and architecture of a future large-scale transmon quantum computer. Other experiments I contributed to are summarized in the conclusion chapter to show the diverse physics that can be studied in cQED experiments.
The quest to design a realizable quantum computer is a dream for many for the past few decades. At the moment, one of the promising designs is the transmon qubit, which is a superconducting qubit is the focus of this work. In order to analyze and design different components of a quantum chip, an understanding of the circuitry is required. By varying the circuit parameters, one can design the system according to requirements by constructing the required physical geometry that incorporates the design parameters. In this thesis work, part of the focus was to understand the transmon qubit circuit parameters, extract the circuit parameters such as capacitances from a physical geometry, build analytic and numerical 3D FEM models. Using a circuit model of the qubit system, the interdependence of the resonators that connects qubits with each other can be studied. Their resonances play a role in the qubit Hamiltonian and can be estimated by constructing accurate simulation models. This problem statement has been dealt with in the thesis work by constructing a hybrid circuitry of standard circuit components and 3D FEM simulated qubit unit cells. The quality factor of the measurement readout resonator of a qubit system needs to be characterized in a qubit system in order to target the rate and resolution at which the measurements can be done. In order to do so, the circuit parameters that affect the quality factor needs to be investigated. This problem statement has also been treated in this work.
This master thesis was dedicated to design, fabricate, and characterize subsystems of superconducting transmon qubits. Especially, focus was on investigating the predictability of the plasma frequency of the transmon, from which its operational properties are govern. In turn, the plasma frequency is governed by the normal state resistance of the two Josephson junctions along with its total capacitance. In\nprevious experiments, this frequency predictability relied entirely upon successful simulations of the system. However, even small simulation errors prove to generate\nsevere consequences for the system and a better, more systematic control is desired.\nIn order to identify and minimize this uncertainty, subsystems of the transmon were isolated and investigated. Test structures were fabricated and used to measure the normal state resistance of tunnel junctions with different areas and oxidation parameters using a four-point probe setup. A regime within which the reproducibility is increased was statistically identified. The shunt capacitance, i.e. the largest contribution to the total capacitance, of transmons was extracted by coupling identical capacitors to resonators. The coupling capacitance of a resonator is related to its external quality factor which was measured from analyzing the reflected microwave signal at cryogenic temperatures.\nThe smallest standard deviation of normal state resistances for 110 junction pairs was measured for junctions with an area 2.37 um^2 to be 1.48%, corresponding to an uncertainty contribution of 2 MHz for a designed plasma frequency of 6 GHz. Six resonators were measured throughout the shunt capacitance experiment and a linear t was used to compare the results with a written model based on conformal mapping.
Superconducting transmon qubits are a leading technology for quantum information processing, yet their reliable operation rests on meticulous calibration and characterization routines. These processes have been fine-tuned and are relatively well understood by the quantum computing community. Nevertheless, it is often challenging for newcomers to compile all the available information into a practical experimental flow. In this tutorial, we present a comprehensive walkthrough for the characterization and optimization of tunable transmon qubits, demonstrated on a commercial five-qubit processor. Moving beyond theoretical description, we detail in a straightforward manner the complete workflow, from cryogenic setup and wiring to parametric amplifier optimum operation, flux sweet-spot identification, pulse calibration, and readout optimization. We also demonstrate the characterization of qubit-qubit coupling, covering all steps before multiqubit operations. This guide serves as a reference for experimentalists seeking to efficiently bring up transmon-based quantum devices.
Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.