Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

InTech eBooks

Single Photon Detection Using Frequency Up-Conversion with Pulse Pumping

Lijun Ma, Oliver Slattery, Xiao Hong Tang

Published Sep 6, 2011• 1 citation
Publisher

Abstract

In any quantum communication system, such as a quantum key distribution (QKD) system, data rates are mainly limited by the system clock rate and the various link losses. While the transmission clock rate is limited by the temporal resolution of the single-photon detectors, losses in a fiber-based quantum communication system can be minimized by operating in the near infrared range (NIR), at 1310 nm or 1550 nm. Commercially available InGaAs-based avalanche photo-diodes (APDs) can be operated as single-photon detectors in this wavelength range [Hadfield, 2009]. Due to the severe after-pulsing, InGaAs APDs are typically used in a gated mode and this can limit their application in high-speed quantum communications systems. Superconducting single-photon detectors (SSPDs) can work in the NIR wavelength range with good performance [Gol’tsman et al. 2001; Hadfield, 2009]. However, SSPDs require cryogenic temperatures, and are not widely available on the commercial market at present. In addition, InGaAs/InP based photomultiplier tubes (PMT) can operate in the NIR range, but its performance is limited by very low detection efficiency (1 % at 1600 nm) and large timing jitter (1.5 ns) [Hamamatsu, 2005]. Microchannel plates (MCP) are micro-capillary electron multipliers coated with an electron-emissive material and multiply photon-excited electrons from a photon cathode [Wiza, 1979]. MCPs usually have faster rise times and lower timing jitter than is achievable with PMTs. InGaAs MCPs can work in the NIR range. These MCPs, but are limited by low detection efficiency (~1 %) [Martin, J. & Hink P. 2003]. On the other hand, silicon based avalanche photo-diodes (Si APDs) are compact, relatively inexpensive, and can be operated at ambient temperatures with high detection efficiency and low noise in the visible or near-visible range. Unfortunately they do not work at wavelengths longer than 1000 nm. For those wavelengths, an up-conversion technique has been developed that uses sum-frequency generation (SFG) in a non-linear optical medium to convert the signal photons to a higher frequency (shorter wavelength) in the visible or near visible range. The up-converted photons can then be detected by a Si APD. Up-conversion detectors use commercially available components and devices, and are a practical solution for many applications in quantum communications. To date, several groups have successfully developed highly efficient up-conversion single-photon detectors in the nearinfrared range using periodically poled lithium niobate (PPLN) waveguides [Diamanti et al., 2005; Langrock et al., 2005; Thew et al., 2006; Tanzilli et al., 2005; Xu et al., 2007;] and bulk crystals [Vandevender & Kwiat, 2004].

DOI
10.5772/19965

Related papers

Single-photon detectors for practical quantum cryptography

Alberto Tosi, Franco Zappa, S. Cova

The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 19, 2012•14 citations

Up–conversion detectors at 1550 nm for quantum communication: review and recent advances

M. Tournier, Olivier Alibart, Florent Doutre +5 more

Up-conversion, or hybrid, detectors have been investigated in quantum communication experiments to replace Indium-Gallium-Arsenide avalanche photodiodes (InGaAs-APD) for the detection of infrared and telecom single photons. Those detectors are based on the supposedly noise-free process of frequency up-conversion, also called sum-frequency generation (SFG), using a second order (χ2) non-linear crystal. Powered by an intense pump laser, this process permits transposing with a certain probability the single photons at telecom wavelengths to the visible range where silicon APDs (Si-APD) operate with a much better performance than InGaAs detectors. To date, the literature reports up-conversion detectors having efficiency and noise figures comparable to that of the best commercially available IngaAs-APDs. However, in all of these previous realizations, a pump-induced noise is always observed which was initially expected to be as low as the dark count level of the Si-APDs. Although this additional noise represents a problem for the detection, up-conversion detectors have advantageously replaced InGaAs-APDs in various long-distance quantum cryptography schemes since they offer a continuous regime operation mode instead of a gated mode necessary for InGaAs-APDs, and the possibility of much higher counting rates. Despite attempted explanations, no detailed nor conclusive study of this noise has been reported.

EAS Publications Series•Jan 1, 2009•3 citations

Detection and spectral measurement of single photons in communication bands using up-conversion technology

Long Ma, Oliver Slattery, Xiao Hong Tang

Quantum information systems are commonly operated in conventional communication bands (1310 and 1550 nm) over an optical fiber to take advantage of low transmission loss. However, the detection and spectral measurement of single photons in these communication bands are limited due to high noise and low sensitivity of single photon detectors in the wavelength ranges. To demonstrate high efficiency detection and high sensitivity spectral measurement, we have implemented a single photon detector and a spectrometer based on frequency up-conversion technology. This detector and spectrometer uses a 5-cm periodically poled lithium niobate (PPLN) waveguide and a tunable pump laser around 1550 nm, to convert signal photons around 1310 to 710 nm. The converted photons are then detected by a silicon-based avalanche photodiode (APD). The overall detection efficiency of the single photon detector is as high as 32%, which is three times higher than commercial InGaAs APDs. The sensitivity of the spectrometer is measured to be −126 dBm, which is at least three orders-of-magnitude better than any commercial optical spectrum analyzer in this wavelength range.

Laser Physics•Apr 2, 2010•11 citations

NIR Single Photon Detectors with Up-Conversion Technology and its Applications in Quantum Communication Systems

Lijun Ma, Oliver Slattery, Xiao Hong Tang

Frequency up-conversion single photon detectors use the principle of sum frequency generation to up-convert single photons in the near IR range to a shorter wavelength for an efficient detection by low cost detectors, such as Si-APDs. The up-conversion detectors are usually operated at room temperature with high detection efficiency and a low dark count rate. The detectors have a very narrow acceptance spectral width and polarization sensitivity, properties that can be exploited in certain applications requiring narrow linewidth or polarization specific detection. These unique characteristics can be used to enhance system performance in some applications, including fiber-based quantum communications systems.

InTech eBooks•Apr 1, 2010•5 citations

Single Photon Detector Comparison in a Quantum Key Distribution Link Testbed

Jonathan L. Habif, David Pearson, Robert H. Hadfield +3 more

We provide a direct comparison between the InGaAs avalanche photodiode (APD) and the NbN superconducting single photon detector (SSPD) for applications in fiber-based quantum cryptography. The quantum efficiency and dark count rate were measured for each detector, and used to calculate the quantum bit error rate (QBER) and shared key rate for a QKD link. The results indicate that, despite low quantum efficiency, the speed of the SSPD makes it a superior detector for quantum information applications. Finally, we present results of an initial integration of an SSPD into a receiver node of the DARPA quantum network to perform quantum key distribution. Encoding quantum information on single photons has enabled the realization of a number of unique communication schemes such as the implementation of the BB84 protocol for quantum key distribution 1 and quantum dense coding. 2 Furthermore, the implementation of these schemes using photons at telecommunication wavelengths has permitted their extension to fiber optic networks, 3,4 drastically increasing the practicality of quantum information processing. To date, the state of the art in commercially available single photon detection at telecommunication wavelengths (1550 nm) has been the thermo-electrically cooled InGaAs avalanche photodiode (APD). The cooled InGaAs APD is generally operated at T = -60°C in the reverse-biased Geiger mode. Though these detectors have been successfully implemented in operating QKD links in optical fiber, the InGaAs APD suffers from afterpulsing effects that limit the key exchange rates. New SPD (single photon detector) technologies based on superconducting materials are emerging that hold tremendous promise for drastically increasing the photon counting rate and eliminating dark noise.57 The SSPD consists of a NbN thin film (t ∼ 5 nm) patterned into a narrow (w ∼ 100 nm) microstrip meander that is ∼ 500μm in length. The detector is cooled to T < 4K in a closed cycle refrigeration unit and a bias current I b is supplied to the device just below the superconducting critical current (I c ). When a photon is incident upon the microstrip superconductivity is broken in the region local to photon absorption and a normal state region is formed in the device. The current passing through the device causes a measurable voltage pulse in the detector that can be amplified and shaped to act as an input for traditional logic circuitry. Due to the unique electronic bandstructure in a superconducting material the intrinsic response time of the device is on the order of picoseconds, so that the repetition rate may be increased above 1 GHz 8 without being susceptible to afterpulsing effects that plague the InGaAs APD. 9 To make a direct comparison between the InGaAs APD and the SSPD both were placed in a SPD characterization testbed to measure quantum efficiency and dark count rate at a variety of bias conditions. The QBER for a QKD link is calculated from the measured parameters and then compared to requirements for a provably secure QKD link. Following detector characterization, one of the nodes of the DARPA Quantum Network operated by BBN Technologies 3 utilized an SSPD in the receiver to transmit key material. The demonstration provides an in situ comparison between the InGaAs APD, normally operated in the BBN link, and the SSPD.

Applied Physics Letters•Oct 25, 2006•0 citations

Frequency up-conversion single-photon detectors for quantum communication systems

Lijun Ma, Joshua C. Bienfang, Oliver Slattery +1 more

Frequency up-conversion technology can be used to increase detection efficiency for near infrared photons, as has been demonstrated in fiber-based quantum communication systems. In a continuous wave pumped up-conversion detector, the temporal resolution is limited by the timing jitter of the detector in the visible range, which limits the maximum clock rate of a quantum communication system. In this paper we describe a scheme to improve the temporal resolution of an up-conversion single-photon detector using multi-wavelength optical-sampling techniques, allowing for increased transmission rates in single-photon communications systems. We experimentally demonstrate our approach with an up-conversion detector using two spectrally and temporally distinct pump pulses, and show that it allows for high-fidelity single-photon detection at twice the rate supported by a conventional single-pump up-conversion detector.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 26, 2011•1 citation
In any quantum communication system, such as a quantum key distribution (QKD) system, data rates are mainly limited by the system clock rate and the various link losses. While the transmission clock rate is limited by the temporal resolution of the single-photon detectors, losses in a fiber-based quantum communication system can be minimized by operating in the near infrared range (NIR), at 1310 nm or 1550 nm. Commercially available InGaAs-based avalanche photo-diodes (APDs) can be operated as single-photon detectors in this wavelength range [Hadfield, 2009]. Due to the severe after-pulsing, InGaAs APDs are typically used in a gated mode and this can limit their application in high-speed quantum communications systems. Superconducting single-photon detectors (SSPDs) can work in the NIR wavelength range with good performance [Gol’tsman et al. 2001; Hadfield, 2009]. However, SSPDs require cryogenic temperatures, and are not widely available on the commercial market at present. In addition, InGaAs/InP based photomultiplier tubes (PMT) can operate in the NIR range, but its performance is limited by very low detection efficiency (1 % at 1600 nm) and large timing jitter (1.5 ns) [Hamamatsu, 2005]. Microchannel plates (MCP) are micro-capillary electron multipliers coated with an electron-emissive material and multiply photon-excited electrons from a photon cathode [Wiza, 1979]. MCPs usually have faster rise times and lower timing jitter than is achievable with PMTs. InGaAs MCPs can work in the NIR range. These MCPs, but are limited by low detection efficiency (~1 %) [Martin, J. & Hink P. 2003]. On the other hand, silicon based avalanche photo-diodes (Si APDs) are compact, relatively inexpensive, and can be operated at ambient temperatures with high detection efficiency and low noise in the visible or near-visible range. Unfortunately they do not work at wavelengths longer than 1000 nm. For those wavelengths, an up-conversion technique has been developed that uses sum-frequency generation (SFG) in a non-linear optical medium to convert the signal photons to a higher frequency (shorter wavelength) in the visible or near visible range. The up-converted photons can then be detected by a Si APD. Up-conversion detectors use commercially available components and devices, and are a practical solution for many applications in quantum communications. To date, several groups have successfully developed highly efficient up-conversion single-photon detectors in the nearinfrared range using periodically poled lithium niobate (PPLN) waveguides [Diamanti et al., 2005; Langrock et al., 2005; Thew et al., 2006; Tanzilli et al., 2005; Xu et al., 2007;] and bulk crystals [Vandevender & Kwiat, 2004].
The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.
Up-conversion, or hybrid, detectors have been investigated in quantum communication experiments to replace Indium-Gallium-Arsenide avalanche photodiodes (InGaAs-APD) for the detection of infrared and telecom single photons. Those detectors are based on the supposedly noise-free process of frequency up-conversion, also called sum-frequency generation (SFG), using a second order (χ2) non-linear crystal. Powered by an intense pump laser, this process permits transposing with a certain probability the single photons at telecom wavelengths to the visible range where silicon APDs (Si-APD) operate with a much better performance than InGaAs detectors. To date, the literature reports up-conversion detectors having efficiency and noise figures comparable to that of the best commercially available IngaAs-APDs. However, in all of these previous realizations, a pump-induced noise is always observed which was initially expected to be as low as the dark count level of the Si-APDs. Although this additional noise represents a problem for the detection, up-conversion detectors have advantageously replaced InGaAs-APDs in various long-distance quantum cryptography schemes since they offer a continuous regime operation mode instead of a gated mode necessary for InGaAs-APDs, and the possibility of much higher counting rates. Despite attempted explanations, no detailed nor conclusive study of this noise has been reported.
Quantum information systems are commonly operated in conventional communication bands (1310 and 1550 nm) over an optical fiber to take advantage of low transmission loss. However, the detection and spectral measurement of single photons in these communication bands are limited due to high noise and low sensitivity of single photon detectors in the wavelength ranges. To demonstrate high efficiency detection and high sensitivity spectral measurement, we have implemented a single photon detector and a spectrometer based on frequency up-conversion technology. This detector and spectrometer uses a 5-cm periodically poled lithium niobate (PPLN) waveguide and a tunable pump laser around 1550 nm, to convert signal photons around 1310 to 710 nm. The converted photons are then detected by a silicon-based avalanche photodiode (APD). The overall detection efficiency of the single photon detector is as high as 32%, which is three times higher than commercial InGaAs APDs. The sensitivity of the spectrometer is measured to be −126 dBm, which is at least three orders-of-magnitude better than any commercial optical spectrum analyzer in this wavelength range.
Frequency up-conversion single photon detectors use the principle of sum frequency generation to up-convert single photons in the near IR range to a shorter wavelength for an efficient detection by low cost detectors, such as Si-APDs. The up-conversion detectors are usually operated at room temperature with high detection efficiency and a low dark count rate. The detectors have a very narrow acceptance spectral width and polarization sensitivity, properties that can be exploited in certain applications requiring narrow linewidth or polarization specific detection. These unique characteristics can be used to enhance system performance in some applications, including fiber-based quantum communications systems.
We provide a direct comparison between the InGaAs avalanche photodiode (APD) and the NbN superconducting single photon detector (SSPD) for applications in fiber-based quantum cryptography. The quantum efficiency and dark count rate were measured for each detector, and used to calculate the quantum bit error rate (QBER) and shared key rate for a QKD link. The results indicate that, despite low quantum efficiency, the speed of the SSPD makes it a superior detector for quantum information applications. Finally, we present results of an initial integration of an SSPD into a receiver node of the DARPA quantum network to perform quantum key distribution. Encoding quantum information on single photons has enabled the realization of a number of unique communication schemes such as the implementation of the BB84 protocol for quantum key distribution 1 and quantum dense coding. 2 Furthermore, the implementation of these schemes using photons at telecommunication wavelengths has permitted their extension to fiber optic networks, 3,4 drastically increasing the practicality of quantum information processing. To date, the state of the art in commercially available single photon detection at telecommunication wavelengths (1550 nm) has been the thermo-electrically cooled InGaAs avalanche photodiode (APD). The cooled InGaAs APD is generally operated at T = -60°C in the reverse-biased Geiger mode. Though these detectors have been successfully implemented in operating QKD links in optical fiber, the InGaAs APD suffers from afterpulsing effects that limit the key exchange rates. New SPD (single photon detector) technologies based on superconducting materials are emerging that hold tremendous promise for drastically increasing the photon counting rate and eliminating dark noise.57 The SSPD consists of a NbN thin film (t ∼ 5 nm) patterned into a narrow (w ∼ 100 nm) microstrip meander that is ∼ 500μm in length. The detector is cooled to T < 4K in a closed cycle refrigeration unit and a bias current I b is supplied to the device just below the superconducting critical current (I c ). When a photon is incident upon the microstrip superconductivity is broken in the region local to photon absorption and a normal state region is formed in the device. The current passing through the device causes a measurable voltage pulse in the detector that can be amplified and shaped to act as an input for traditional logic circuitry. Due to the unique electronic bandstructure in a superconducting material the intrinsic response time of the device is on the order of picoseconds, so that the repetition rate may be increased above 1 GHz 8 without being susceptible to afterpulsing effects that plague the InGaAs APD. 9 To make a direct comparison between the InGaAs APD and the SSPD both were placed in a SPD characterization testbed to measure quantum efficiency and dark count rate at a variety of bias conditions. The QBER for a QKD link is calculated from the measured parameters and then compared to requirements for a provably secure QKD link. Following detector characterization, one of the nodes of the DARPA Quantum Network operated by BBN Technologies 3 utilized an SSPD in the receiver to transmit key material. The demonstration provides an in situ comparison between the InGaAs APD, normally operated in the BBN link, and the SSPD.
Frequency up-conversion technology can be used to increase detection efficiency for near infrared photons, as has been demonstrated in fiber-based quantum communication systems. In a continuous wave pumped up-conversion detector, the temporal resolution is limited by the timing jitter of the detector in the visible range, which limits the maximum clock rate of a quantum communication system. In this paper we describe a scheme to improve the temporal resolution of an up-conversion single-photon detector using multi-wavelength optical-sampling techniques, allowing for increased transmission rates in single-photon communications systems. We experimentally demonstrate our approach with an up-conversion detector using two spectrally and temporally distinct pump pulses, and show that it allows for high-fidelity single-photon detection at twice the rate supported by a conventional single-pump up-conversion detector.