Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Softwaretechnik-Trends

Source conductance scaling for high frequency superconducting quasiparticle receivers

Qing Ke, M. J. Feldman

Published Jan 1, 1992• 4 citations
OpenAlex

Abstract

It has been suggested that the optimum source conductance G(sub s) for the superconductor-insulator-superconductor (SIS) quasiparticle mixer should have a l/f dependence. This would imply that the critical current density of SIS junctions used for mixing should increase as frequency squared, a stringent constraint on the design of submillimeter SIS mixers, rather than in simple proportion to frequency as previously believed. We have used Tucker's quantum theory of mixing for extensive numerical calculations to determine G(sub s) for an optimized SIS receiver. We find that G(sub s) is very roughly independent of frequency (except for the best junctions at low frequency), and discuss the implications of our results for the design of submillimeter SIS mixers.

Related papers

Optimum source conductance for high frequency superconducting quasiparticle receivers

Qing Ke, M. J. Feldman

The authors have used the quantum theory of mixing for extensive numerical calculations to determine the mixer source conductance G/sub s/ required to optimize a superconductor-insulator-superconductor (SIS) quasiparticle heterodyne receiver. The optimum G/sub s/ matches an empirical formula which can be understood by a simple derivation. Previous work indicated that G/sub s/ should vary inversely with frequency, and this implies that the critical current density of SIS junctions used for mixing should increase as frequency squared, a stringent constraint on the design of submillimeter SIS mixers. On the contrary, it was found that G/sub s/ is more weakly dependent upon frequency, and the implications for the design of submillimeter SIS mixers are discussed.>

IEEE Transactions on Microwave Theory and Techniques•Apr 1, 1993•22 citations

High-frequency limits of superconducting tunnel junction mixers

Dag Winkler, T. Claeson

We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.

Journal of Applied Physics•Dec 1, 1987•35 citations

Frequency dependence of quasiparticle mixers

W. C. Danchi, Edmund C. Sutton

An analysis of the frequency dependence of superconductor-insulator-normal (SIN) and superconductor-insulator-superconductor (SIS) quasiparticle mixers is presented. Power-law expressions for conversion loss and mixer shot-noise temperature for the double-sideband SIN mixer are derived from the Tucker theory for the case of a source conductance which is small compared to the conductance of the junction. For an ideal SIN tunnel junction at T=0 the mixer conversion efficiency is shown to decrease approximately linearly with frequency up to f=Δ/h. From f=Δ/h to 2Δ/h the conversion efficiency remains approximately constant, while above f=2Δ/h it rolls off as the inverse square of the frequency. Expressions for the shot-noise contribution to the mixer noise temperature are also derived. At frequencies up to f=Δ/h the noise temperature rises as the square root of the frequency. From f=Δ/h to f=2Δ/h the noise temperature of the mixer increases linearly with frequency, whereas above f=2Δ/h it rises as the cube of the frequency. Conversion efficiency and noise temperature are also calculated numerically for the SIN mixer. Good agreement is found between the frequency dependencies calculated analytically in the limit of small local oscillator power and the numerical calculations for optimal pumping. The frequency dependence of the nonideal SIS junction is also analyzed, and shown to yield similar results, with the characteristic frequencies Δ/h and 2Δ/h for a SIN mixer transformed into 2Δ/h and 4Δ/h, respectively. Expressions also are derived for the saturation power as a function of frequency.

Journal of Applied Physics•Dec 1, 1986•33 citations

A Circuit for Tuning Superconductor–Insulator–Superconductor Mixers Using Distributed Tunnel Junctions

Yoshinori Uzawa, Masanori Takeda, Zhen Wang

A circuit that produces broadband impedance matching with low-current-density junctions at submillimeter wavelengths for tuning superconductor–insulator–superconductor (SIS) mixers is described; it consists of half-wavelength distributed SIS junctions connected alternately by half-wavelength microstrip lines. It is made of Nb and was designed for two practical source impedances using numerical calculation based on the Mattis–Bardeen theory of the anomalous skin effect at 660 GHz, assuming SIS junctions with a current density of 5 kA/cm 2 . An SIS mixer tuned using this circuit had a large fractional bandwidth of more than 18%, below -10 dB matching, even though the assumed ω C J R N product was about 16. Investigation of the mixer performance using Tucker's quantum theory of mixing showed that it has excellent broadband and low-noise characteristics compared with conventional mixers consisting of half- or full-wavelength distributed elements.

Japanese Journal of Applied Physics•Jan 15, 2003•2 citations

SIS (Superconductor-Insulator-Superconductor) mixer research

M. J. Feldman

Theoretical and experimental research has been conducted to elucidate the basic physics behind the properties of superconductor-insulator-superconductor (SIS) tunnel junction receiving devices. The quantum theory of mixing was employedto calculate the saturation behavior of the SIS mixer and the SIS direct detector. The direct detector was found to saturate at far higher powers than previously believed, allowing the possibility of practical application of this device. Experiments verified the saturation theory. The mixer saturation expression led to the formulation of frequency scaling regions. The origin of quantum noise sources are completely minimized. The mixer quantum noise limit was shown to be reached in only two special cases. Computer calculations determined that the behavior of SIS receivers divides into two regimes, low and high frequencies, the cross-over frequency depending upon junction quality. The properties of these two regimes were delineated. All previous SIS receivers have operated in the low frequency regime. Plasma-etched niobium nitride edge junctions have been fabricated using a novel barrier formation process. These junctions have excellent current-voltage characteristics, but their precise physical nature has not yet been determined. (Author)

Final Report•Mar 1, 1987•0 citations

Noise parameters of SIS mixers

Larry R. D’Addario

It has been shown that low-noise receivers can be constructed at millimeter wavelengths by using mixers containing superconducting tunnel junctions as the nonlinear elements. This is possible because of both the low intrinsic noise of these devices and their potential for high conversion gain. Here, the quantum theory of mixing is used to derive the full-noise parameters and small-signal parameters of sinusoidally pumped SIS (superconductor-insulator-superconductor) junctions. These are then put into a form that allows the theory of two-port linear networks to be brought to bear, allowing calculation of such useful parameters as minimum noise temperature, optimum source impedance, available (or exchangeable) gain at minimum noise, and stability factor. These quantities are properties of the pumped junction that do not depend on the source or load impedance, but do depend on the terminations at the image and harmonic sideband frequencies. The harmonic sidebands are taken to be shorted, and the image termination dependence is studied. Numerical results are presented for both ideal (BSC theory) and practical (measured current-voltage characteristic) junctions. The noise parameters of the cascade connection of an SIS mixer and a (noisy) IF amplifier are considered, leading to a specification of the optimum coupling network between the two. It is noted that the SIS mixer is usually not unconditionally stable, but that oscillation can be avoided by careful design of the IF coupling network.< >

IEEE Transactions on Microwave Theory and Techniques•Jul 1, 1988•19 citations
It has been suggested that the optimum source conductance G(sub s) for the superconductor-insulator-superconductor (SIS) quasiparticle mixer should have a l/f dependence. This would imply that the critical current density of SIS junctions used for mixing should increase as frequency squared, a stringent constraint on the design of submillimeter SIS mixers, rather than in simple proportion to frequency as previously believed. We have used Tucker's quantum theory of mixing for extensive numerical calculations to determine G(sub s) for an optimized SIS receiver. We find that G(sub s) is very roughly independent of frequency (except for the best junctions at low frequency), and discuss the implications of our results for the design of submillimeter SIS mixers.
The authors have used the quantum theory of mixing for extensive numerical calculations to determine the mixer source conductance G/sub s/ required to optimize a superconductor-insulator-superconductor (SIS) quasiparticle heterodyne receiver. The optimum G/sub s/ matches an empirical formula which can be understood by a simple derivation. Previous work indicated that G/sub s/ should vary inversely with frequency, and this implies that the critical current density of SIS junctions used for mixing should increase as frequency squared, a stringent constraint on the design of submillimeter SIS mixers. On the contrary, it was found that G/sub s/ is more weakly dependent upon frequency, and the implications for the design of submillimeter SIS mixers are discussed.>
We have investigated high-frequency limits of superconducting quasiparticle mixers from experiments on Al/Al-oxide-In/Al (or Ag) tunnel junctions, and from calculations based on Tucker’s quantum theory of mixing (QTM). The small superconducting energy gap of Al enabled us to study mixer performance at around the junction gap frequency, fg =(Δ1+Δ2)/h≊87 GHz, of superconductor-insulator-superconductor (SIS) mixers, and at twice the junction gap frequency for S-I-normal metal (SIN) mixers ( fg =Δ1/h) with available millimeter wave sources. Because of the low transition temperature of Al (Tc ≊1.3 K), a dilution refrigerator was used for providing temperatures below 1 K. The best mixer conversion efficiency was obtained for a low-resistance (∼34 Ω) six-junction array SIS mixer operated at f/fg ≊1 (in this case 73 GHz). The coupled single sideband conversion gain (with no image rejection) was −13.8 dB and the available conversion gain was estimated to −8.4 dB. Complicating nonequilibrium phenomena made it difficult to compare the performance of these relatively high-current-density mixers to the QTM. However, good agreement between calculated and corresponding measured conversion efficiencies and dynamic resistance values was obtained for the low-current-density mixers. Noise due to switching between rf-induced Josephson steps and interference from Josephson mixing could be quenched by a magnetic field. Several high-frequency limits are considered in this paper (such as Josephson switching noise, nonequilibrium phenomena, pair breaking, and energy gap limitations). Our results indicate that submillimeter wave SIS mixer receivers are likely to perform well, at least up to their gap frequencies, i.e., the THz region for large gap superconductors. Our QTM calculations showed that conversion gain larger than unity should be possible up to twice the gap frequency. Above this frequency the conversion loss will increase rapidly.
An analysis of the frequency dependence of superconductor-insulator-normal (SIN) and superconductor-insulator-superconductor (SIS) quasiparticle mixers is presented. Power-law expressions for conversion loss and mixer shot-noise temperature for the double-sideband SIN mixer are derived from the Tucker theory for the case of a source conductance which is small compared to the conductance of the junction. For an ideal SIN tunnel junction at T=0 the mixer conversion efficiency is shown to decrease approximately linearly with frequency up to f=Δ/h. From f=Δ/h to 2Δ/h the conversion efficiency remains approximately constant, while above f=2Δ/h it rolls off as the inverse square of the frequency. Expressions for the shot-noise contribution to the mixer noise temperature are also derived. At frequencies up to f=Δ/h the noise temperature rises as the square root of the frequency. From f=Δ/h to f=2Δ/h the noise temperature of the mixer increases linearly with frequency, whereas above f=2Δ/h it rises as the cube of the frequency. Conversion efficiency and noise temperature are also calculated numerically for the SIN mixer. Good agreement is found between the frequency dependencies calculated analytically in the limit of small local oscillator power and the numerical calculations for optimal pumping. The frequency dependence of the nonideal SIS junction is also analyzed, and shown to yield similar results, with the characteristic frequencies Δ/h and 2Δ/h for a SIN mixer transformed into 2Δ/h and 4Δ/h, respectively. Expressions also are derived for the saturation power as a function of frequency.
A circuit that produces broadband impedance matching with low-current-density junctions at submillimeter wavelengths for tuning superconductor–insulator–superconductor (SIS) mixers is described; it consists of half-wavelength distributed SIS junctions connected alternately by half-wavelength microstrip lines. It is made of Nb and was designed for two practical source impedances using numerical calculation based on the Mattis–Bardeen theory of the anomalous skin effect at 660 GHz, assuming SIS junctions with a current density of 5 kA/cm 2 . An SIS mixer tuned using this circuit had a large fractional bandwidth of more than 18%, below -10 dB matching, even though the assumed ω C J R N product was about 16. Investigation of the mixer performance using Tucker's quantum theory of mixing showed that it has excellent broadband and low-noise characteristics compared with conventional mixers consisting of half- or full-wavelength distributed elements.
Theoretical and experimental research has been conducted to elucidate the basic physics behind the properties of superconductor-insulator-superconductor (SIS) tunnel junction receiving devices. The quantum theory of mixing was employedto calculate the saturation behavior of the SIS mixer and the SIS direct detector. The direct detector was found to saturate at far higher powers than previously believed, allowing the possibility of practical application of this device. Experiments verified the saturation theory. The mixer saturation expression led to the formulation of frequency scaling regions. The origin of quantum noise sources are completely minimized. The mixer quantum noise limit was shown to be reached in only two special cases. Computer calculations determined that the behavior of SIS receivers divides into two regimes, low and high frequencies, the cross-over frequency depending upon junction quality. The properties of these two regimes were delineated. All previous SIS receivers have operated in the low frequency regime. Plasma-etched niobium nitride edge junctions have been fabricated using a novel barrier formation process. These junctions have excellent current-voltage characteristics, but their precise physical nature has not yet been determined. (Author)
It has been shown that low-noise receivers can be constructed at millimeter wavelengths by using mixers containing superconducting tunnel junctions as the nonlinear elements. This is possible because of both the low intrinsic noise of these devices and their potential for high conversion gain. Here, the quantum theory of mixing is used to derive the full-noise parameters and small-signal parameters of sinusoidally pumped SIS (superconductor-insulator-superconductor) junctions. These are then put into a form that allows the theory of two-port linear networks to be brought to bear, allowing calculation of such useful parameters as minimum noise temperature, optimum source impedance, available (or exchangeable) gain at minimum noise, and stability factor. These quantities are properties of the pumped junction that do not depend on the source or load impedance, but do depend on the terminations at the image and harmonic sideband frequencies. The harmonic sidebands are taken to be shorted, and the image termination dependence is studied. Numerical results are presented for both ideal (BSC theory) and practical (measured current-voltage characteristic) junctions. The noise parameters of the cascade connection of an SIS mixer and a (noisy) IF amplifier are considered, leading to a specification of the optimum coupling network between the two. It is noted that the SIS mixer is usually not unconditionally stable, but that oscillation can be avoided by careful design of the IF coupling network.< >