In this thesis, the evanescent field sensing techniques of tapered optical nanofibres and microspherical resonators are investigated. This includes evanescent field spectroscopy of a silica nanofibre in a rubidium vapour; thermo-optical tuning of Er:Yb co-doped phosphate glass microspheres; optomechanical properties of microspherical pendulums; and the fabrication and characterisation of borosilicate microbubble resonators. Doppler-broadened and sub-Doppler absorption spectroscopic techniques are performed around the D2 transition (780.24 nm) of rubidium using the evanescent field produced at the waist of a tapered nanofibre with input probe powers as low as 55 nW. Doppler-broadened Zeeman shifts and a preliminary dichroic atomic vapour laser lock (DAVLL) line shape are also observed via the nanofibre waist with an applied magnetic field of 60 G. This device has the potential for laser frequency stabilisation while also studying the effects of atom-surface interactions. A non-invasive thermo-optical tuning technique of Er:Yb co-doped microspheres to specific arbitrary wavelengths is demonstrated particularly to 1294 nm and the 5S1/2F=3 to 5P3/2Fʹ=4 laser cooling transition of 85Rb. Reversible tuning ranges of up to 474 GHz and on resonance cavity timescales on the order of 100 s are reported. This procedure has prospective applications for sensing a variety of atomic or molecular species in a cavity quantum electrodynamics (QED) experiments. The mechanical characteristics of a silica microsphere pendulum with a relatively low spring constant of 10-4 Nm-1 are explored. A novel method of frequency sweeping the motion of the pendulum to determine its natural resonance frequencies while overriding its sensitivity to environmental noise is proposed. An estimated force of 0.25 N is required to actuate the pendulum by a displacement of (1-2) μm. It is suggested that this is of sufficient magnitude to be experienced between two evanescently coupled microspheres (photonic molecule) and enable spatial trapping of the micropendulum. Finally, single-input borosilicate microbubble resonators with diameters <100 μm are fabricated using a CO2 laser. Optical whispering gallery mode spectra are observed via evanescent coupling with a tapered fibre. A red-shift of (4-22) GHz of the resonance modes is detected when the hollow cavity was filled with nano-filtered water. A polarisation conversion effect, with an efficiency of 10%, is observed when the diameter of the coupling tapered fibre waist is varied. This effect is also achieved by simply varying the polarisation of the input light in the tapered fibre where the efficiency is optimised to 92%. Thus, the microbubble device acts as a reversible band-pass to band-stop optical filter for cavity-QED, integrated solid-state and semiconductor circuit applications.
In this thesis, the evanescent field sensing techniques of tapered optical nanofibres and microspherical resonators are investigated. This includes evanescent field spectroscopy of a silica nanofibre in a rubidium vapour; thermo-optical tuning of Er:Yb co-doped phosphate glass microspheres; optomechanical properties of microspherical pendulums; and the fabrication and characterisation of borosilicate microbubble resonators. Doppler-broadened and sub-Doppler absorption spectroscopic techniques are performed around the D2 transition (780.24 nm) of rubidium using the evanescent field produced at the waist of a tapered nanofibre with input probe powers as low as 55 nW. Doppler-broadened Zeeman shifts and a preliminary dichroic atomic vapour laser lock (DAVLL) line shape are also observed via the nanofibre waist with an applied magnetic field of 60 G. This device has the potential for laser frequency stabilisation while also studying the effects of atom-surface interactions. A non-invasive thermo-optical tuning technique of Er:Yb co-doped microspheres to specific arbitrary wavelengths is demonstrated particularly to 1294 nm and the 5S1/2F=3 to 5P3/2Fʹ=4 laser cooling transition of 85Rb. Reversible tuning ranges of up to 474 GHz and on resonance cavity timescales on the order of 100 s are reported. This procedure has prospective applications for sensing a variety of atomic or molecular species in a cavity quantum electrodynamics (QED) experiments. The mechanical characteristics of a silica microsphere pendulum with a relatively low spring constant of 10-4 Nm-1 are explored. A novel method of frequency sweeping the motion of the pendulum to determine its natural resonance frequencies while overriding its sensitivity to environmental noise is proposed. An estimated force of 0.25 N is required to actuate the pendulum by a displacement of (1-2) μm. It is suggested that this is of sufficient magnitude to be experienced between two evanescently coupled microspheres (photonic molecule) and enable spatial trapping of the micropendulum. Finally, single-input borosilicate microbubble resonators with diameters <100 μm are fabricated using a CO2 laser. Optical whispering gallery mode spectra are observed via evanescent coupling with a tapered fibre. A red-shift of (4-22) GHz of the resonance modes is detected when the hollow cavity was filled with nano-filtered water. A polarisation conversion effect, with an efficiency of 10%, is observed when the diameter of the coupling tapered fibre waist is varied. This effect is also achieved by simply varying the polarisation of the input light in the tapered fibre where the efficiency is optimised to 92%. Thus, the microbubble device acts as a reversible band-pass to band-stop optical filter for cavity-QED, integrated solid-state and semiconductor circuit applications.
Optical nanofibres (ONFs) are very thin optical waveguides with sub-wavelength diameters. ONFs have very high evanescent fields and the guided light is confined strongly in the transverse direction. These fibres can be used to achieve strong light-matter interactions. Atoms around the waist of an ONF can be probed by collecting the atomic fluorescence coupling or by measuring the transmission (or the polarisation) of the probe beam sent through it. This thesis presents experiments using ONFs for probing and manipulating laser-cooled 87Rb atoms. As an initial experiment, a single mode ONF was integrated into a magneto-optical trap (MOT) and used for measuring the characteristics of the MOT, such as the loading time and the average temperature of the atom cloud. The effect of a near-resonant probe beam on the local temperature of the cold atoms has been studied. Next, the ONF was used for manipulating the atoms in the evanescent fields region in order to generate nonlinear optical effects. Four-wave mixing, ac Stark effect (Autler-Townes splitting) and electromagnetically induced transparency have been observed at unprecedented ultralow power levels. In another experiment, a few-mode ONF, supporting only the fundamental mode and the first higher order mode group, has been used for studying cold atoms. A higher pumping rate of the atomic fluorescence into the higher order fibreguided modes and more interactions with the surrounding atoms for higher order mode evanescent light, when compared to signals for the fundamental mode, have been identified. The results obtained in the thesis are particularly for a fundamental understanding of light-atom interactions when atoms are near a dielectric surface and also for the development of fibre-based quantum information technologies. Atoms coupled to ONFs could be used for preparing intrinsically fibre-coupled quantum nodes for quantum computing and the studies presented here are significant for a detailed understanding of such a system.
A dielectric microsphere may be considered as an artificial photonic atom. The electromagnetic modes in the microsphere are completely assigned with indexes similar to those used to characterize simple atomic systems. Microsphere modes, as well as microring or microdisk, trap light in circular orbits near the sphere surface and strongly modify the phase of the interacting light, resulting in very steep dispersions. Pulse propagation experiments were performed in a system consisting of a fiber taper coupled with a silica glass microsphere, and it was shown that the light velocity in the system can be largely changed through the control of the coupling strength. Slow light was also demonstrated in a system in which two ultrahigh-Q silica microspheres of different diameters were coupled in tandem to a fiber taper demonstrating classical analog of electromagnetically induced transparency in atomic system. Here, we employed interferometric techniques based on the Mach-Zehnder interferometer for examining extremely steep dispersions induced by whispering gallery modes with a quality factor on the order of Q 1⁄4 10. Such a narrow resonance in the dielectric microsphere is comparable to that in cooled atomic systems. We successfully observed both normal and anomalous dispersions at the resonant frequency, depending on the coupling strength between the sphere and the fiber. Figure 1 shows our experimental system based on an interferometric setup. We used the second harmonics of a single mode ring cavity Nd3þ yttrium aluminum garnet (Nd3þ:YAG) laser with a line width of 1 kHz at 532 nm. The laser frequency was tuned using thermal control of the ring cavity length, over a mode-hop-free range of greater than 10GHz. The reference arm was empty, while the sample arm contained the microsphere-fiber system. Silica microspheres were fabricated from standard telecommunication optical fiber. The end of the etched fiber was fused using a CO2 laser and the microsphere formed due to the surface tension. The experiments were performed with a microsphere 60 mm in diameter. The fiber taper was also fabricated from the same telecommunication fiber. The typical fiber waist diameter at the coupling region was 0.5 mm. A large number of spectrally overlapping resonance modes exist within a microsphere. The fiber taper method is essential for coupling the incident light to a specific whispering gallery mode selectively and efficiently. The microsphere was attached to a translation stage controlled by a piezo actuator. The relative position between the sphere and the fiber were carefully adjusted so that we could observe spectrally isolated whispering gallery modes with proper coupling strength. The optical path length and dispersion were equalized in each arm as completely as possible. The fringe pattern was captured using a charge-coupled device (CCD) camera for each frequency increment. The observed interference patterns appeared as concentric circles due to the interference between the plain reference wave and the spherical wave from the sample arm. A least square fit for each fringe pattern was performed to extract the phase information in the transmitted light. Figures 2(a) and 2(b) show examples of transmission spectra through the microsphere fiber taper coupled system. These spectra were taken in two different whispering gallery modes at different laser frequencies in the mode-hop-free laser tuning range. The transmission dips appear when the incident laser frequencies are resonant at specific whispering gallery modes in the microsphere. The two whispering gallery modes shown in Figs. 2(a) and 2(b) are denoted as WG1 and WG2, respectively. The transmission minimum was Tmin 1⁄4 0:12, and the resonance width was 1⁄4 BS
We present experimental results on an all-optical, thermally-assisted technique for broad range tuning of microsphere cavity resonance modes to arbitrary probe wavelengths. An erbium:ytterbium co-doped phosphate glass (Schott IOG-2) microsphere is pumped at 978 nm via the supporting stem and the heat generated by absorption of the pump light expands the cavity and changes the refractive index. This is a robust tuning method that decouples the pump from the probe and allows fine tuning of the microsphere's whispering gallery modes. Pump/probe experiments were performed to demonstrate thermo-optical tuning to specific probe wavelengths, including the5S1/2F= 3 to5P3/2F'= 4 laser cooling transition of rubidium-85. This is of particular interest for cavity quantum electrodynamics (QED)-type experiments, while the broad tuning range achievable is useful for integrated photonic devices, including sensors and modulators.
We present experimental results on an all-optical, thermally-assisted technique for broad range tuning of microsphere cavity resonance modes to arbitrary probe wavelengths. An erbium:ytterbium co-doped phosphate glass (Schott IOG-2) microsphere is pumped at 978 nm via the supporting stem and the heat generated by absorption of the pump light expands the cavity and changes the refractive index. This is a robust tuning method that decouples the pump from the probe and allows fine tuning of the microsphere's whispering gallery modes. Pump/probe experiments were performed to demonstrate thermo-optical tuning to specific probe wavelengths, including the 5 S 1/2 F= 3 to 5 P 3/2 F'= 4 laser cooling transition of rubidium-85. This is of particular interest for cavity quantum electrodynamics (QED)-type experiments, while the broad tuning range achievable is useful for integrated photonic devices, including sensors and modulators.
"In this thesis, laser cooling and trapping techniques are implemented to forrn a cold atom cloud of 85Rb atoms in a magneto-optical trap (Mon configuration. The system produces an atom cloud of~ 1.5 mm in diameter, containing ~ 108 atoms and an average temperature in the sub-Doppler range. Tapered optical fibres (TOFs) are also detailed here, including their guiding properties and the process used for their fabrication. Many possible applications for TOFs have been proposed and one such application is investigated, i.e. the use of TOFs as highly sensitive atom probes. The research results contained within this thesis describe two techniques whereby TOFs can be used as probes. By overlapping the TOF and a cold atom cloud spontaneously emitted photons from the trapped atoms are coupled into the guided mode of the TOF. This then allows characteristics of the cold atom cloud, such as the cloud profile, loading time, lifetime and temperature to be determined. The second technique uses light guided by, but external to, the fibre, i.e. within the evanescent field, to probe the surrounding environment, which may be a cold atom cloud or a background vapour. The work presented also describes a theoretical basis for quantum state preparation using multi-level-atom optics, allowing for the creation of spatial superposition states in which one has perfect control over the population distribution and also the phase relation."
Efficient coupling of light to quantum emitters, such as atoms, molecules or quantum dots, is one of the great challenges in current research. The interaction can be strongly enhanced by coupling the emitter to the eva-nescent field of subwavelength dielectric waveguides that offer strong lateral confinement of the guided light. In this context subwavelength diameter optical nanofibers as part of a tapered optical fiber (TOF) have proven to be powerful tool which also provide an efficient transfer of the light from the interaction region to an optical bus, that is to say, from the nanofiber to an optical fiber. rnAnother approach towards enhancing light–matter interaction is to employ an optical resonator in which the light is circulating and thus passes the emitters many times. Here, both approaches are combined by experi-mentally realizing a microresonator with an integrated nanofiber waist. This is achieved by building a fiber-integrated Fabry-Perot type resonator from two fiber Bragg grating mirrors with a stop-band near the cesium D2-line wavelength. The characteristics of this resonator fulfill the requirements of nonlinear optics, optical sensing, and cavity quantum electrodynamics in the strong-coupling regime. Together with its advantageous features, such as a constant high coupling strength over a large volume, tunability, high transmission outside the mirror stop band, and a monolithic design, this resonator is a promising tool for experiments with nanofiber-coupled atomic ensembles in the strong-coupling regime. rnThe resonator's high sensitivity to the optical properties of the nanofiber provides a probe for changes of phys-ical parameters that affect the guided optical mode, e.g., the temperature via the thermo-optic effect of silica. Utilizing this detection scheme, the thermalization dynamics due to far-field heat radiation of a nanofiber is studied over a large temperature range. This investigation provides, for the first time, a measurement of the total radiated power of an object with a diameter smaller than all absorption lengths in the thermal spectrum at the level of a single object of deterministic shape and material. The results show excellent agreement with an ab initio thermodynamic model that considers heat radiation as a volumetric effect and that takes the emitter shape and size relative to the emission wavelength into account. Modeling and investigating the thermalization of microscopic objects with arbitrary shape from first principles is of fundamental interest and has important applications, such as heat management in nano-devices or radiative forcing of aerosols in Earth's climate system. rnUsing a similar method, the effect of the TOF's mechanical modes on the polarization and phase of the fiber-guided light is studied. The measurement results show that in typical TOFs these quantities exhibit high-frequency thermal fluctuations. They originate from high-Q torsional oscillations that couple to the nanofiber-guided light via the strain-optic effect. An ab-initio opto-mechanical model…