Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Two-wavelength switching with a distributed-feed back semiconductor optical amplifier (DFBSOA)

Antonio Hurtado Villavieja, Ana González‐Marcos, José Antonio Martín Pereda, Matthew Adams

Published Feb 13, 2006• 0 citations
OpenAlex

Abstract

Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 mm-distributed feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.

Related papers

Two-wavelength switching with a distributed-feedback semiconductor optical amplifier (DFBSOA)

Antonio Hurtado, Ana Pilar Gonzalez-Marcos, José A. Martín-Pereda +1 more

Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 µm-distributed feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.

IEE Proceedings - Optoelectronics•Jan 25, 2006•20 citations

Two-wavelength switching with 1550 nm semiconductor laser amplifiers

Antonio Hurtado, M.J. Adams

Feature Issue on Photonics in SwitchingTwo-wavelength switching operation between two signals at different wavelengths is reported using the optical bistability occurring in two different semiconductor laser amplifiers. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. Switching of a signal beam by another control beam at different wavelength is reported experimentally with a 1550 nm distributed feedback semiconductor optical amplifier. Also, a theoretical model has been generated to analyze the wavelength switching operation with a novel amplifier type--the 1550 nm vertical cavity semiconductor optical amplifier (VCSOA). Using a 1550 nm VCSOA, wavelength switching operation is reported with a calculated input power below 1 μW. This low input power requirement for switching added to the high-frequency response of the VCSOA, and the ease of fabricating 2D arrays of these devices due to the vertical structure, makes the VCSOA a very interesting device for use in optical switching applications in the optical telecommunication networks.

Journal of Optical Networking•Jan 1, 2007•21 citations

Optical bistability using a Fabry–Perot semiconductor-laser amplifier with two holding beams

Hitoshi Kawaguchi, Kyo Inoue, Hiroyuki Tani

Bistable switching of an optical signal beam by a control beam with a different wavelength, using the nonlinearity of a Fabry-Perot semiconductor-laser amplifier, is reported for the first time to the authors' knowledge. Depending on the initial detuning of the optical signal beam, both normal (counterclockwise) and reverse (clockwise) hysteresis are theoretically and experimentally obtained in the signal output power as a function of the control input power.

Optics Letters•Jul 1, 1987•32 citations

Reflective optical bistability and nonlinear switching in a 1550-nm vertical-cavity semiconductor optical amplifier (VCSOA)

Antonio Hurtado, Ian D. Henning, M.J. Adams

We report experimental measurements of Optical Bistability (OB) and nonlinear switching in a 1550 nm-Vertical-Cavity Semiconductor Optical Amplifier (VCSOA) operated in reflection and biased below and above its threshold current. Two different types of OB and nonlinear switching, anticlockwise and clockwise, have been observed in both the optical power and wavelength domain. The influence of important parameters including the bias current, the initial wavelength detuning and the optical input power has also been studied. The existence of diverse forms of OB and nonlinear switching in a VCSOA operated in reflection opens the door for the development of inverting and non-inverting logic gates, using, respectively, the anticlockwise or the clockwise nonlinear switching transitions appearing in the VCSOA under external optical injection.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 18, 2007•0 citations

Optical Bistability and Nonlinear Gain in a 1550 nm-Vertical Cavity Semiconductor Optical Amplifier (VCSOA) with High On-Off Contrast Ratio

Antonio Hurtado, Ian D. Henning, M.J. Adams

This paper reports on the experimental observation of power and wavelength optical bistability (OB) and nonlinear gain in a 1550 nm- vertical cavity semiconductor optical amplifier (VCSOA) biased just below threshold and operated in reflection. Two different shapes of power and wavelength OB and nonlinear gain, anticlockwise and clockwise, have been experimentally observed, both with high on-off contrast ratio.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2007•0 citations

Observation of bistability in a Vertical-Cavity Semiconductor Optical Amplifier (VCSOA)

Pengyue Wen, Michael Sánchez, Matthias Groß +1 more

We report, the first time to our knowledge, an observation of optical bistability in a Vertical-Cavity Semiconductor Optical Amplifier (VCSOA) operated in reflection mode. Counterclockwise hysteresis loops are obtained over a range of initial phase detuning and bias currents. One hysteresis loop is observed experimentally with an input power as low as 2 ìW when the device is biased at 98% of its lasing threshold. We also numerically simulate the optical bistability and obtain good agreement with our experimental observations. Bistable VCSOAs significantly advances the prospect of dense 2-D array of low switching-intensity all-optical logic and memory elements.

Optics Express•Nov 4, 2002•41 citations
Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 mm-distributed
feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique
an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.
Switching of a signal beam by another control beam at different wavelength is demonstrated experimentally using the optical bistability occurring in a 1.55 µm-distributed feedback semiconductor optical amplifier (DFBSOA) working in reflection. Counterclockwise (S-shaped) and reverse (clockwise) bistability are observed in the output of the control and the signal beam respectively, as the power of the input control signal is increased. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. The switching properties of the DFBSOA are studied experimentally as the applied bias current is increased from below to above threshold and for different levels of optical power in the signal beam and different wavelength detunings between both input signals. Higher on-off extinction ratios, wider bistable loops and lower input power requirements for switching are obtained when the DFBSOA is operated slightly above its threshold value.
Feature Issue on Photonics in SwitchingTwo-wavelength switching operation between two signals at different wavelengths is reported using the optical bistability occurring in two different semiconductor laser amplifiers. With this technique an optical signal can be set in either of the optical input wavelengths by appropriate choice of the powers of the input signals. Switching of a signal beam by another control beam at different wavelength is reported experimentally with a 1550 nm distributed feedback semiconductor optical amplifier. Also, a theoretical model has been generated to analyze the wavelength switching operation with a novel amplifier type--the 1550 nm vertical cavity semiconductor optical amplifier (VCSOA). Using a 1550 nm VCSOA, wavelength switching operation is reported with a calculated input power below 1 μW. This low input power requirement for switching added to the high-frequency response of the VCSOA, and the ease of fabricating 2D arrays of these devices due to the vertical structure, makes the VCSOA a very interesting device for use in optical switching applications in the optical telecommunication networks.
We report experimental measurements of Optical Bistability (OB) and nonlinear switching in a 1550 nm-Vertical-Cavity Semiconductor Optical Amplifier (VCSOA) operated in reflection and biased below and above its threshold current. Two different types of OB and nonlinear switching, anticlockwise and clockwise, have been observed in both the optical power and wavelength domain. The influence of important parameters including the bias current, the initial wavelength detuning and the optical input power has also been studied. The existence of diverse forms of OB and nonlinear switching in a VCSOA operated in reflection opens the door for the development of inverting and non-inverting logic gates, using, respectively, the anticlockwise or the clockwise nonlinear switching transitions appearing in the VCSOA under external optical injection.
We report, the first time to our knowledge, an observation of optical bistability in a Vertical-Cavity Semiconductor Optical Amplifier (VCSOA) operated in reflection mode. Counterclockwise hysteresis loops are obtained over a range of initial phase detuning and bias currents. One hysteresis loop is observed experimentally with an input power as low as 2 ìW when the device is biased at 98% of its lasing threshold. We also numerically simulate the optical bistability and obtain good agreement with our experimental observations. Bistable VCSOAs significantly advances the prospect of dense 2-D array of low switching-intensity all-optical logic and memory elements.