Scalable superconducting quantum computation requires fast, high-fidelity readout. Currently, this is assisted through cryogenic amplification of the readout signal. In traditional dispersive readout schemes, the amplifiers that are used to provide high signal-to-noise ratio also generate thermal noise that can decohere the qubits, demanding additional ferrite-based isolators to suppress this noise. Here, we integrate a chip-scale microwave switch, the tunable inductive bridge, into the readout chain of a fixed-frequency transmon. Flux-pulsing the switch, such that it transmits only during the readout, did not make a discernable difference to qubit coherence, residual excited-state population, or readout fidelity metrics. By injecting broadband noise that mimics amplifier thermal photons, we show that the switch suppresses the resulting qubit dephasing by more than $30$~dB, consistent with its independently measured on-off ratio, establishing it as a potential chip-based integrated replacement for readout-chain isolators.
Scalable superconducting quantum computation requires fast, high-fidelity readout. Currently, this is assisted through cryogenic amplification of the readout signal. In traditional dispersive readout schemes, the amplifiers that are used to provide high signal-to-noise ratio also generate thermal noise that can decohere the qubits, demanding additional ferrite-based isolators to suppress this noise. Here, we integrate a chip-scale microwave switch, the tunable inductive bridge, into the readout chain of a fixed-frequency transmon. Flux-pulsing the switch, such that it transmits only during the readout, did not make a discernable difference to qubit coherence, residual excited-state population, or readout fidelity metrics. By injecting broadband noise that mimics amplifier thermal photons, we show that the switch suppresses the resulting qubit dephasing by more than 30~dB, consistent with its independently measured on-off ratio, establishing it as a potential chip-based integrated replacement for readout-chain isolators.
Nonreciprocal microwave devices, such as circulators and isolators, are needed in high-fidelity qubit readout schemes to unidirectionally route the readout signals and protect the qubits against noise coming from the output chain.However, cryogenic circulators and isolators are prohibitive in scalable superconducting architectures because they rely on magnetic materials.Here we report a fast (750 ns) high-fidelity (95%) quantum nondemolition readout of a coherent superconducting qubit (T 1 = 52 μs, T 2E = 35 μs) without any nonreciprocal magnetic devices.We use in our readout chain a microwave-controlled qubit readout multichip module (QRMCM) that integrates interferometric directional Josephson devices consisting of an isolator and a reconfigurable isolator or amplifier device, and an off-chip low-pass filter.Using the QRMCM, we demonstrate isolation up to 45 dB within 13 MHz, when both directional devices are operated as isolators, and low-noise amplification in excess of 10 dB within a dynamical bandwidth of 10 MHz, when the reconfigurable device is operated as an amplifier.We also investigate the dependence of the qubit coherence times T ϕ and T 2E on the isolation response of the QRMCM, which we control in situ using the microwave drives feeding the isolators.Furthermore, by directly comparing the QRMCM performance with that of a state-of-art configuration (with T 2E ≈ 2T 1 ) that uses a pair of wideband magnetic isolators, we find that the excess pure dephasing measured with the QRMCM (for which T 2E ≈ T 1 ) is likely limited by the residual thermal photon population in the readout resonator.Improved versions of the QRMCM could replace magnetic circulators and isolators in large superconducting quantum processors.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
High-fidelity qubit measurement is a critical element of all quantum computing architectures. In superconducting systems, qubits are typically measured by probing a readout resonator with a weak microwave tone that must be amplified before reaching the room temperature electronics. Superconducting parametric amplifiers have been widely adopted as the first amplifier in the chain, primarily because of their low noise performance, approaching the quantum limit. However, they require isolators and circulators to route signals up the measurement chain and to protect qubits from amplified noise. While these commercial components are wideband and simple to use, their intrinsic loss, size, and magnetic shielding requirements impact overall measurement efficiency and scalability. Here we report a parametric amplifier that achieves both broadband forward amplification and backward isolation in a single, compact, non-magnetic circuit that could be integrated on chip with superconducting qubits. The approach relies on a nonlinear transmission line that supports traveling-wave parametric amplification of forward propagating signals, and isolation via frequency conversion of backward propagating signals. This traveling-wave parametric amplifier and converter has the potential to reduce the readout hardware overhead when scaling up the size of superconducting quantum computers.
Scalable, high-fidelity quantum-state readout remains a central challenge in the development of large-scale superconducting quantum processors. Conventional dispersive readout architectures depend on bulky isolators and external amplifiers, introducing significant hardware overhead and limiting opportunities for on-chip information processing. In this work, we propose a novel approach that embeds a nonlinear Superconducting Nonlinear Asymmetric Inductive eLement (SNAIL) into the readout chain, enabling coherent and directional processing of readout signals directly on-chip. This embedded SNAIL platform allows frequency-multiplexed resonators to interact through engineered couplings, forming a tunable readout-amplifier-output architecture that can manipulate quantum readout data \textit{in situ}. Through theoretical modeling and numerical optimization, we show that this platform enhances fidelity, suppresses measurement-induced decoherence, and simplifies hardware complexity. These results establish the hybridized SNAIL as a promising building block for scalable and coherent quantum-state readout in next-generation processors.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
Superconducting qubits are a leading platform for scalable quantum computing and quantum error correction. One feature of this platform is the ability to perform projective measurements orders of magnitude more quickly than qubit decoherence times. Such measurements are enabled by the use of quantum-limited parametric amplifiers in conjunction with ferrite circulators-magnetic devices which provide isolation from noise and decoherence due to amplifier backaction. Because these nonreciprocal elements have limited performance and are not easily integrated on chip, it has been a long-standing goal to replace them with a scalable alternative. Here, we demonstrate a solution to this problem by using a superconducting switch to control the coupling between a qubit and amplifier. Doing so, we measure a transmon qubit using a single, chip-scale device to provide both parametric amplification and isolation from the bulk of amplifier backaction. This measurement is also fast, high fidelity, and has 70% efficiency, comparable to the best that has been reported in any superconducting qubit measurement. As such, this work constitutes a high-quality platform for the scalable measurement of superconducting qubits.