Superconducting traveling-wave parametric amplifiers (TWPAs) are essential elements for enhancing the signal-to-noise ratio (SNR) and thus the read-out fidelity of superconducting qubits because of their high gain and near quantum-limited noise. However, the impact of the pump source, e.g., phase noise on these amplifiers, has not yet been studied. In this work, we show that among the two amplification processes in JTWPAs, the three-wave mixing (3WM) process is more sensitive to the pump phase noise than the four-wave mixing (4WM) process. We show that the even-order nonlinearity of 4th order and above in three-wave mixing is responsible for more than 10 dB increase of phase noise at high frequency offsets within the phase noise mask as the power of the pump increases. A polynomial model of the amplifier and cyclo-stationary property of phase noise also corroborate with the simulations. The Harmonic Balance (HB) periodic noise analysis tool and Leeson phase noise model in Keysight Advanced Design System (ADS) simulator were used in this study.
Superconducting traveling-wave parametric amplifiers (TWPAs) are essential elements for enhancing the signal-to-noise ratio (SNR) and thus the read-out fidelity of superconducting qubits because of their high gain and near quantum-limited noise. However, the impact of the pump source, e.g., phase noise on these amplifiers, has not yet been studied. In this work, we show that among the two amplification processes in JTWPAs, the three-wave mixing (3WM) process is more sensitive to the pump phase noise than the four-wave mixing (4WM) process. We show that the even-order nonlinearity of 4th order and above in three-wave mixing is responsible for more than 10 dB increase of phase noise at high frequency offsets within the phase noise mask as the power of the pump increases. A polynomial model of the amplifier and cyclo-stationary property of phase noise also corroborate with the simulations. The Harmonic Balance (HB) periodic noise analysis tool and Leeson phase noise model in Keysight Advanced Design System (ADS) simulator were used in this study.
Abstract A Josephson traveling-wave parametric amplifier (JTWPA) is indispensable for the high-fidelity readout of superconducting qubits, owing to its broadband gain and near-quantum-limited noise performance. Conventional JTWPAs implemented with 0-Josephson junctions (0-JTWPAs) avoid magnetic-flux bias but rely on Kerr nonlinearity, which leads to pump-power-dependent phase mismatch, gain ripple, and a limited dynamic range. More recently, three-wave-mixing (3WM) JTWPAs employing flux-biased rf-SQUIDs have been proposed to suppress Kerr effects. However, these designs require a significant external flux bias per unit cell, which complicates cryogenic hardware, introduces sensitivity to flux noise, and limits scalability in large arrays. In this study, we propose and analyze a π -junction-based JTWPA ( π -JTWPA) in which the intrinsic π phase shift of the junction effectively displaces the operating point of the current–phase relation. This approach aims to realize 3WM-type nonlinearity with reduced flux bias while preserving broadband amplification, thereby simplifying flux-bias distribution, enhancing robustness against flux noise, and providing a pathway toward scalable, multiplexed quantum readout architectures. In addition, we examine the potential applicability of the π -JTWPA in four-wave-mixing (4WM) operation.
Predicting the performance of traveling-wave parametric amplifiers (TWPAs) based on nonlinear elements like superconducting Josephson junctions (JJs) is vital for qubit read-out in quantum computers. The purpose of this article is twofold: (a) to demonstrate how nonlinear inductors based on combinations of JJs can be modeled in commercial circuit simulators, and (b) to show how the harmonic balance (HB) is used in the reliable prediction of the amplifier performance e.g., gain and pump harmonic power conversion. Experimental characterization of two types of TWPA architectures is compared with simulations to showcase the reliability of the HB method. We disseminate the modeling know-how and techniques to new designers of parametric amplifiers.
Superconducting traveling-wave parametric amplifiers (TWPAs) are increasingly used in various applications, including quantum computing, quantum sensing, and dark matter detection. However, one important characteristic of these amplifiers, gain compression, has not received much attention. As a result, there is a lack of comprehensive experimental exploration of this phenomenon in the existing literature. In this study, we present an experimental investigation of gain compression in a Josephson traveling-wave parametric amplifier based on a four-wave mixing process. We have implemented a novel setup to monitor the complex transmission of both the pump and signal tones, which allows us to simultaneously track pump depletion and signal amplification as functions of signal power and frequency across the entire bandwidth of the device. Our findings indicate that, while pump depletion occurs during gain compression, it is not the only mechanism involved in the saturation of a TWPA. Power-induced phase-matching processes also take place within the device. This study provides valuable insights for optimizing TWPAs for applications that require high total input power, such as multiplexed qubit readout or broadband photon emission.
In order to build a large-scale quantum computer, one of the requirements is high-fidelity
multiplexed qubit readout, which in turn relies on the use of ultralow-noise
amplifiers. While Josephson Parametric Amplifiers (JPAs), using a cavity with
few Josephson junctions, have shown promising results for single qubit readout,
they have limitations such as low saturation power and a gain-bandwidth product
restriction. This makes them less suited for frequency multiplexed qubit readout. A
current-pumped Josephson Travelling-Wave Parametric Amplifier (JTWPA), using
4-wave mixing in a lumped-element transmission line, features both high saturation
power as well as no restriction on large bandwidth and high gain. This is possible
due to multiple junctions and the lack of a cavity. However, also this current pumped
JTWPA has an inherent problem, namely phase mismatch between the pump and
the signal. This prevents exponential gain. In this thesis, a current pumped JTWPA
using the resonant phase matching (RPM) technique to reduce the phase mismatch
problem is studied and characterised. The JTWPA shows high gain, high saturation
power and a large signal-to-noise ratio improvement. The JTWPA is also used for
qubit readout, for which it clearly improves the readout fidelity.
Superconducting traveling-wave parametric amplifiers (TWPAs) are increasingly used in various applications, including quantum computing, quantum sensing, and dark matter detection. However, one important characteristic of these amplifiers, gain compression, has not received much attention. As a result, there is a lack of comprehensive experimental exploration of this phenomenon in the existing literature. In this study, we present an experimental investigation of gain compression in a Josephson traveling-wave parametric amplifier based on a four-wave mixing process. We have implemented a novel setup to monitor the complex transmission of both the pump and signal tones, which allows us to simultaneously track pump depletion and signal amplification as functions of signal power and frequency across the entire bandwidth of the device. Our findings indicate that, while pump depletion occurs during gain compression, it is not the only mechanism involved in the saturation of a TWPA. Power-induced phase-matching processes also take place within the device. This study provides valuable insights for optimizing TWPAs for applications that require high total input power, such as multiplexed qubit readout or broadband photon emission.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.