Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2511.09498 · Review of Scientific Instruments

Photothermal resistivity alignment of optical fibers to superconducting nanowire single-photon detectors

Martin Baránek, Dušan Lorenc, T. Ščepka, J. Šoltýs, Iuliia V. Vetrova, Štefan Haščík, M. Grajcar, P. Neilinger

Published Mar 1, 2026• 0 citations
arXivHTMLPDF

Abstract

We demonstrate a straightforward optoelectronic fiber alignment technique for superconducting nanowire single-photon detectors (SNSPDs), which exploits the temperature-dependent resistance of a nanowire under optical absorption. The target nanowire is illuminated via the fiber, and the local absorption of light heats the wire, causing a change in its resistivity. Scanning the fiber over the nanowire, the change in its resistivity is monitored by lock-in amplifier, mapping the spatial photothermal response correlated with absorption and coupling efficiency. The maximum of the response corresponds to optimal fiber-SNSPD alignment. This method allows for aligning the fiber to the center of the meander with sub-micron precision. The response is robust to variations in the angle and height of the fiber, providing an alternative or complement to fiber-to-chip alignment methods based on the back-reflection or transmission measurement.

DOI
10.1063/5.0311869

Related papers

Superconducting nanowire single-photon detector in an optical cavity for front-side illumination

Burm Baek, Jeffrey A. Stern, Sae Woo Nam

We have integrated superconducting nanowire single-photon detectors (SNSPDs) with an optical cavity design for front-side illumination. Our optical cavity design increases the coupling efficiency of light to the nanowire detector and enables straightforward proximity fiber-coupling for a multichannel detector system. Using a confocal optical scanning technique, we measured a significantly enhanced optical absorptance of 73% in comparison with 20% in a typical bare nanowire device at 1550 nm and 3 K. Our method of fabrication of these devices on a silicon wafer and the local optical absorptance measurement are important steps toward developing next-generation SNSPD technology.

Applied Physics Letters•Nov 9, 2009•39 citations

Fractal superconducting nanowire single-photon detectors with reduced polarization sensitivity

Xiaoming Chi, Kai Zou, Chao Gu +8 more

We demonstrate superconducting nanowire single-photon detectors (SNSPDs) based on a fractal design of the nanowires to reduce the polarization sensitivity of detection efficiency. We patterned niobium titanium nitride thin films into Peano curves with a linewidth of 100 nm and integrated the nanowires with optical microcavities to enhance their optical absorption. At a base temperature of 2.6 K, the fractal SNSPD exhibited a polarization-maximum device efficiency of 67% and a polarization-minimum device efficiency of 61% at a wavelength of 1550 nm. Therefore, the polarization sensitivity, defined as their ratio, was 1.1, lower than the polarization sensitivity of the SNSPDs in the meander design. The reduced polarization sensitivity of the detector could be maintained for higher-order spatial modes in multimode optical fibers and could tolerate misalignment between the optical mode and the detector. This fractal design is applicable to both amorphous and polycrystalline materials that are commonly used for making SNSPDs.

Optics Letters•Oct 8, 2018•46 citations

Hybrid Integration of a Superconducting Nanowire Single‐Photon Detector Directly on the Fiber Facet

Fan Yang, Qingyuan Zhao, Yanghui Huang +17 more

ABSTRACT Directly integrating superconducting nanowire single‐photon detectors (SNSPDs) on the fiber facet could significantly reduce coupling loss and alignment uncertainty, enabling an all‐fiber single‐photon detector with high detection efficiency, robust coupling, and compact size. However, the material and mechanical incompatibility between bulky optical fibers and nano‐fabricated ultrathin nanowires makes fabrication and integration challenging. Here, we demonstrate a hybrid integration method that involves fabricating individual membrane‐based detectors and optical mirrors separately, followed by their precise assembly on fiber facets. After integration, the detectors exhibit saturated quantum efficiency, a maximum system detection efficiency of 68.6%, a timing jitter as low as 26 ps, and a counting rate of up to 51.7 Mcps. These performance metrics are comparable to SNSPDs on standard silicon wafers. Moreover, this integration enables a fiber facet coupling regime where the detector is embedded in the guide mode of the incident light, resulting in an exceptionally broad detection bandwidth (1310–1640 nm) with less than 2.3% reduction in efficiency. The successful fiber facet integration of SNSPDs not only provides an alternative coupling strategy but also introduces a single‐photon detection capability into the group of fiber‐integrated optoelectronics, paving the way for low‐loss, long‐range quantum communication and distributed sensing systems.

Laser & Photonics Review•Mar 13, 2026•2 citations

Self-aligned multi-channel superconducting nanowire single-photon detectors

Risheng Cheng, Xiang Guo, Xiaosong Ma +4 more

We describe a micromachining process to allow back-side coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). This approach enables a back-illuminated detector structure which separates the optical access and electrical readout on two sides of the chip and thus allows for compact integration of multi-channel detectors. As proof of principle, we show the integration of four detectors on the same silicon chip with two different designs and their performances are compared. In the optimized design, the device shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, all achieved without the use of metal reflectors or distributed Bragg reflectors (DBRs). This back-illumination approach also eliminates the cross-talk between different detection channels.

arXiv:1601.01719•Optics Express•Nov 14, 2016•16 citations

Fiber coupling of superconducting nanowire single-photon detectors

刘登宽 LIU Deng-kuan, 陈思井 CHEN Si-jing, Lixing You +2 more

In order to investigate the characteristics of the package and fiber coupling of a Superconducting Nanowire Single-photon Detector(SNSPD),the SNSPD was successfully built up in our laboratory.Experiments show that the quantum efficiencies of the detector under different light wavelengths are 6%@1310nm and 3%@1550nm when the dark count rate is 100 Hz.Then,as the distance(gap) between SNSPD and optical fiber would be changed due to the thermal stress during cooling,and would cause a misalignment,two kinds of fiber coupling methods to modulate the gap at room temperature were proposed.Finally,by altering the wavelength of the input light,the exact values of the gap at different temperatures were measured and then the influence of temperature on the gap were figured out by an experiment.The experimental results indicate that decreases of the gap for the two packages are 4.1 μm and 17 μm when the temperature dereases 270 K.Based on the analysis of package material and structure,the gaps at both room and low temperature were calculated theoretically.The result fits well with that of the experiments and it may offer some references to the design of new package and fiber coupling in the future.

Optics and Precision Engineering•Jan 1, 2013•2 citations

Efficiently Coupling Light to Superconducting Nanowire Single-Photon Detectors

Xiaolong Hu, Charles W. Holzwarth, D. Masciarelli +2 more

We designed superconducting nanowire single-photon detectors (SNSPDs) integrated with silver optical antennae for free-space coupling and a dielectric waveguide for fiber coupling. According to our finite-element simulation, (1) for the free-space coupling, the absorptance of the NbN nanowire for TM-polarized photons at the wavelength of 1550 nm can be as high as 96% by adding silver optical antennae; (2) for the fiber coupling, the absorptance of the NbN nanowire for TE-like-polarized photons can reach 76% including coupling efficiency at the wavelength of 1550 nm by adding a silicon nitride waveguide and an inverse-taper coupler.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•90 citations
We demonstrate a straightforward optoelectronic fiber alignment technique for superconducting nanowire single-photon detectors (SNSPDs), which exploits the temperature-dependent resistance of a nanowire under optical absorption. The target nanowire is illuminated via the fiber, and the local absorption of light heats the wire, causing a change in its resistivity. Scanning the fiber over the nanowire, the change in its resistivity is monitored by lock-in amplifier, mapping the spatial photothermal response correlated with absorption and coupling efficiency. The maximum of the response corresponds to optimal fiber-SNSPD alignment. This method allows for aligning the fiber to the center of the meander with sub-micron precision. The response is robust to variations in the angle and height of the fiber, providing an alternative or complement to fiber-to-chip alignment methods based on the back-reflection or transmission measurement.
We have integrated superconducting nanowire single-photon detectors (SNSPDs) with an optical cavity design for front-side illumination. Our optical cavity design increases the coupling efficiency of light to the nanowire detector and enables straightforward proximity fiber-coupling for a multichannel detector system. Using a confocal optical scanning technique, we measured a significantly enhanced optical absorptance of 73% in comparison with 20% in a typical bare nanowire device at 1550 nm and 3 K. Our method of fabrication of these devices on a silicon wafer and the local optical absorptance measurement are important steps toward developing next-generation SNSPD technology.
We demonstrate superconducting nanowire single-photon detectors (SNSPDs) based on a fractal design of the nanowires to reduce the polarization sensitivity of detection efficiency. We patterned niobium titanium nitride thin films into Peano curves with a linewidth of 100 nm and integrated the nanowires with optical microcavities to enhance their optical absorption. At a base temperature of 2.6 K, the fractal SNSPD exhibited a polarization-maximum device efficiency of 67% and a polarization-minimum device efficiency of 61% at a wavelength of 1550 nm. Therefore, the polarization sensitivity, defined as their ratio, was 1.1, lower than the polarization sensitivity of the SNSPDs in the meander design. The reduced polarization sensitivity of the detector could be maintained for higher-order spatial modes in multimode optical fibers and could tolerate misalignment between the optical mode and the detector. This fractal design is applicable to both amorphous and polycrystalline materials that are commonly used for making SNSPDs.
ABSTRACT Directly integrating superconducting nanowire single‐photon detectors (SNSPDs) on the fiber facet could significantly reduce coupling loss and alignment uncertainty, enabling an all‐fiber single‐photon detector with high detection efficiency, robust coupling, and compact size. However, the material and mechanical incompatibility between bulky optical fibers and nano‐fabricated ultrathin nanowires makes fabrication and integration challenging. Here, we demonstrate a hybrid integration method that involves fabricating individual membrane‐based detectors and optical mirrors separately, followed by their precise assembly on fiber facets. After integration, the detectors exhibit saturated quantum efficiency, a maximum system detection efficiency of 68.6%, a timing jitter as low as 26 ps, and a counting rate of up to 51.7 Mcps. These performance metrics are comparable to SNSPDs on standard silicon wafers. Moreover, this integration enables a fiber facet coupling regime where the detector is embedded in the guide mode of the incident light, resulting in an exceptionally broad detection bandwidth (1310–1640 nm) with less than 2.3% reduction in efficiency. The successful fiber facet integration of SNSPDs not only provides an alternative coupling strategy but also introduces a single‐photon detection capability into the group of fiber‐integrated optoelectronics, paving the way for low‐loss, long‐range quantum communication and distributed sensing systems.
We describe a micromachining process to allow back-side coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). This approach enables a back-illuminated detector structure which separates the optical access and electrical readout on two sides of the chip and thus allows for compact integration of multi-channel detectors. As proof of principle, we show the integration of four detectors on the same silicon chip with two different designs and their performances are compared. In the optimized design, the device shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, all achieved without the use of metal reflectors or distributed Bragg reflectors (DBRs). This back-illumination approach also eliminates the cross-talk between different detection channels.
In order to investigate the characteristics of the package and fiber coupling of a Superconducting Nanowire Single-photon Detector(SNSPD),the SNSPD was successfully built up in our laboratory.Experiments show that the quantum efficiencies of the detector under different light wavelengths are 6%@1310nm and 3%@1550nm when the dark count rate is 100 Hz.Then,as the distance(gap) between SNSPD and optical fiber would be changed due to the thermal stress during cooling,and would cause a misalignment,two kinds of fiber coupling methods to modulate the gap at room temperature were proposed.Finally,by altering the wavelength of the input light,the exact values of the gap at different temperatures were measured and then the influence of temperature on the gap were figured out by an experiment.The experimental results indicate that decreases of the gap for the two packages are 4.1 μm and 17 μm when the temperature dereases 270 K.Based on the analysis of package material and structure,the gaps at both room and low temperature were calculated theoretically.The result fits well with that of the experiments and it may offer some references to the design of new package and fiber coupling in the future.
We designed superconducting nanowire single-photon detectors (SNSPDs) integrated with silver optical antennae for free-space coupling and a dielectric waveguide for fiber coupling. According to our finite-element simulation, (1) for the free-space coupling, the absorptance of the NbN nanowire for TM-polarized photons at the wavelength of 1550 nm can be as high as 96% by adding silver optical antennae; (2) for the fiber coupling, the absorptance of the NbN nanowire for TE-like-polarized photons can reach 76% including coupling efficiency at the wavelength of 1550 nm by adding a silicon nitride waveguide and an inverse-taper coupler.