The high-sensitivity quantum detection of a resonant classical force acting on a quantum harmonic oscillator can be significantly improved by employing a resonant optical parametric transducer. This technique leverages the unique properties of parametric interactions to enhance the response of the measurement system while maintaining quantum-limited performance. We demonstrate that such a configuration not only enables quantum back-action evading (BAE) measurements, surpassing the Standard Quantum Limit (SQL) of sensitivity, it also provides a mechanism for noiseless amplification of the classical signal. The key to this enhancement lies in the ability of the parametric transducer to generate and separately measure the upper and lower modulation sidebands induced by the external force. By decoupling and analyzing these sidebands independently, the system becomes capable of amplifying the signal without introducing additional noise, effectively circumventing quantum measurement constraints.
The high-sensitivity quantum detection of a resonant classical force acting on a quantum harmonic oscillator can be significantly improved by employing a resonant optical parametric transducer. This technique leverages the unique properties of parametric interactions to enhance the response of the measurement system while maintaining quantum-limited performance. We demonstrate that such a configuration not only enables quantum back-action evading (BAE) measurements, surpassing the Standard Quantum Limit (SQL) of sensitivity, it also provides a mechanism for noiseless amplification of the classical signal. The key to this enhancement lies in the ability of the parametric transducer to generate and separately measure the upper and lower modulation sidebands induced by the external force. By decoupling and analyzing these sidebands independently, the system becomes capable of amplifying the signal without introducing additional noise, effectively circumventing quantum measurement constraints.
The Standard Quantum Limit (SQL) in classical force detection using mechanical systems arises from quantum back-action, which disturbs the oscillator’s evolution during measurement. We present a theoretical analysis of a scheme that enables broadband back-action evading (BAE) force sensing by employing a multidimensional optical transducer. The proposed system consists of a mechanical oscillator coupled to an optical structure supporting three distinct optical modes, with mode spacing approximately matched to the mechanical resonance. The central mode is coherently pumped, and the signal is extracted by monitoring the light emitted from the adjacent sideband modes. By selecting appropriate optical quadratures for detection and applying tailored post-processing to the measurement data, our approach suppresses back-action noise across a wide frequency range, enabling sensitivity beyond the SQL. The architecture can be interpreted as a composite system hosting quantum-mechanics-free subsystems (QMFS), which effectively isolate the measured observable from quantum fluctuations by exploiting correlations akin to those found in systems with engineered “negative mass” response. We also show that the adjacent sideband modes are entangled and discuss possible methods for detecting this entanglement. This configuration opens a promising route toward high-precision quantum metrology without being constrained by quantum measurement noise.
The standard quantum limit (SQL) of a classical mechanical force detection results from quantum back action perturbing evolution of a mechanical system. In this paper we show that usage of a multidimensional optical transducer may enable a broadband quantum back action evading measurement. We study theoretically a corresponding technique of measurement of a resonant signal force acting on a linear mechanical oscillator coupled to a generic optical system with three optical modes with separation nearly equal to the mechanical frequency. The measurement is performed by optical pumping of the central optical mode and analyzing the light escaping the two other modes. By detecting optimal quadrature components of the optical modes and postprocessing the measurement results we are able to exclude the back action in a broad frequency band and characterize the force with sensitivity better than the SQL. We show that the proposed scheme is similar to the multidimensional system containing quantum-mechanics-free subsystems which can evade the SQL using the idea of the so-called negative mass [M. Tsang and C. M. Caves, Phys. Rev. X 2, 031016 (2012).].
Abstract A theoretical scheme is proposed to enhance the sensitivity of force sensors with quantum non-demolition measurement (QND) in an optomechanical setup assisted by four-tone optical driving and an optical parametric amplifier (OPA). With the help of special drive, the system can be simplified as the typical type of QND for force sensing, so that the backaction noise can be evaded to surpass the standard quantum limit. Besides, the added noise can be suppressed owing to the modified optical susceptibility resulting from the OPA. By introducing two oscillators coupling with two charged bodies respectively, the signal can be enhanced with the nonlinearity caused by Coulomb interaction, while the noise presents an exponential decrease. Moreover, considering the homodyne detection effect, the range of system parameters and frequency bands will be broadened. The present investigation may provide a route toward simultaneously evading backaction noise, reducing the mechanical thermal noise, and enhancing the external signal, which can be an alternative design for sensitive devices.
Unlike classical systems, the very act of observing quantum systems perturbs their behaviour. This introduces noise, which imposes limits on the knowledge that can be obtained through measurement. Certain measurement techniques, known generally as quantum non-demolition (QND) measurements, exist to circumvent this noise. An alternative method to evade backaction noise is to amplify the observable of interest above the noise. However, this generally leaves the system in a different state, and is therefore not considered a QND measurement. In this thesis, I examine the benefits of amplification for various kinds of measurement of mechanical harmonic oscillators which, at the micrometre and nanometre scale, comprise an emerging quantum technology. For this prototypical case, modulation of the spring constant, also known as parametric amplification, is a well-studied noiseless amplification technique. Using the theory of trajectories developed in the field of quantum optics, I show that a weak measurement combined with a detuned parametric drive achieves the same ends as strong QND measurement. Namely, it allows backaction-free observation of one quadrature of mechanical motion, and through this, quantum squeezing below the quantum zero-point motion. This equivalence is experimentally confirmed in the classical limit using an optically detected, electrically modulated cantilever. In addition, I analyse similar amplification enhanced techniques for quantum entanglement and quantum tomography. These results are applicable to research in quantum optomechanics and electromechanics, and can be translated to other kinds of quantum harmonic oscillators, such as microwave cavities.
We investigate the reduction of measurement-added noise in force sensing by analyzing its power spectral density (PSD) within a hybrid optomechanical system. The setup is comprised of an optomechanical cavity equipped with a movable mirror which acts as the mechanical oscillator, a stationary semi-transparent mirror, a superconducting qubit, and an optical parametric amplifier (OPA). By utilizing the concept of coherent quantum noise cancellation (CQNC), we derive the conditions necessary for complete cancellation of back-action force, thereby enhancing force sensitivity. Furthermore, with the gradual increase in the OPA pump gains, we suppress the sensitivity beyond the standard quantum limit (SQL) at a lower value of laser power. The removal of back-action noise, along with the reduction of shot noise, improves force detection capabilities, thereby surpassing the standard quantum limit associated with weak force detection.
We theoretically investigate quantum measurement noise in a hybrid optomechanical system, focusing on radiation pressure back action and its impact on force sensing. The setup consists of an optomechanical cavity with a movable mirror, a fixed semi transparent mirror, an ensemble of quantum dots (QD) coupled to the cavity mode, and an intracavity optical parametric amplifier (OPA). We show how the QD induced response, together with the system nonlinearity, modifies the noise spectral density and thereby improves the force measurement sensitivity. In this setup, coherent quantum noise cancellation (CQNC) can completely remove the back action noise. In addition, increasing the OPA pump gain enables sensitivity beyond the standard quantum limit (SQL) at reduced laser power. These combined effects allow weak force sensing beyond the SQL.