Superconducting travelling wave parametric amplifiers (TWPAs) are broadband near-quantum limited microwave amplifiers commonly used for qubit readout and a wide range of other applications in quantum technologies. The performance of these amplifiers depends on achieving impedance matching to minimise reflected signals. Here we apply a microwave calibration technique to extract the S-parameters of a Josephson junction based TWPA in-operando. This enables reflections occurring at the TWPA and its extended network of components to be quantified, and we find that the in-operation performance can be well described by the off-state measured S-parameters.
Superconducting travelling wave parametric amplifiers (TWPAs) are broadband near-quantum limited microwave amplifiers commonly used for qubit readout and a wide range of other applications in quantum technologies. The performance of these amplifiers depends on achieving impedance matching to minimise reflected signals. Here we apply a microwave calibration technique to extract the S-parameters of a Josephson junction based TWPA in-operando. This enables reflections occurring at the TWPA and its extended network of components to be quantified, and we find that the in-operation performance can be well described by the off-state measured S-parameters.
Superconducting traveling wave parametric amplifiers (TWPAs) are broadband near-quantum limited microwave amplifiers commonly used for qubit readout and a wide range of other applications in quantum technologies. The performance of these amplifiers depends on achieving impedance matching to minimize reflected signals. Here, we apply a microwave calibration technique to extract the S-parameters of a Josephson junction based TWPA in-operando. This enables reflections occurring at the TWPA and its extended network of components to be quantified, and we find that the in-operation performance can be well described by the off-state measured S-parameters.
Recent progress in physics has increased the necessity for ultra-low noise amplifiers capable of operating at the quantum limit performance. These amplifiers are essential to enhance astronomical detection, dark-matter search, and qubit readout in quantum computing, among other applications. Superconducting Josephson junction Travelling Wave Parametric Amplifiers (JTWPAs) operated in the microwave range, have demonstrated high gain over several gigahertz (GHz) bandwidth, with quantum-limited noise performance and minimal heat dissipation. These excellent properties make JTWPAs an ideal solution for ultra-low noise amplification. This thesis delves into the design, fabrication and characterisation of JTWPAs operated in the microwave (1-16 GHz) and the W-band (70-115GHz) regimes. A generalised coupled-mode equations (CME) framework describing JTWPAs based on Josephson junctions and DC superconducting quantum interference devices (SQUIDs) is introduced. This framework can be combined with electromagnetic (EM) simulation softwares to model the JTWPAs, facilitating their design. It is therefore used to model two microwave JTWPA designs, using parallel plate capacitors (PPCs) and interdigitated capacitors (IDCs). The fabrication and characterisation of both designs are presented, and possible fabrication and design issues are carefully discussed. Despite these issues, we observed broadband gain in the JTWPA with PPCs, achieving > 20 dB gain at several frequency points, and a measured P1dB = −95.8dBm when operated at 17.3 dB. The RF properties of a 500-junction Josephson array are also presented in this manuscript. The device creates a Fabry-Perot cavity, leading to non-travelling wave parametric effects, such as narrow-band gain. We also observed indications of efficient phase-sensitive amplification. The thesis is concluded with the first — to the best of our knowledge — experimental attempt to extend the operational frequency of a JTWPA to the W-band. The novel design, fabrication techniques and characterisation of the W-band JTWPA are discussed in detail in this manuscript, leading to promising results suggesting that JTWPA could operate at high frequencies.
Bringing signals from quantum to classical, from few-photon to many-photon levels for further processing, is a common challenge in rising quantum technologies. These include quantum computing, quantum communication, quantum sensing, radio astronomy, and dark matter searches, typically operating at microwave frequencies and millikelvin temperatures. Superconducting parametric amplifiers, as the first piece in the readout chain, have become a cornerstone of these technologies, since they offer unrivaled noise performance near the quantum-mechanical limit and high gain to surpass the noise of subsequent amplifiers. A notable implementation is the Josephson traveling-wave parametric amplifier (TWPA), which stands out due to its bandwidth of several Gigahertz and high saturation power, often larger than -100 dBm. These key properties come at the cost of complexity in design and fabrication: TWPA metamaterials often contain several thousands of Josephson junctions. Designing high-gain TWPAs involves three major challenges: ensuring impedance-matching, phase-matching of parametric amplification, and suppressing unwanted processes, all achievable through sub-wavelength dispersion engineering. This thesis covers the circuit design and analysis, implementation, and experimental characterization of a dispersion-engineered TWPA based on radio-frequency superconducting interference devices (rf-SQUIDs). It focuses on a detailed investigation of dispersion-engineering techniques and their effects on amplifier performance, particularly through the use of time-domain circuit simulations to analyze the multimode dynamics of the circuit. The experimentally realized device features 18 dB of gain, an instantaneous bandwidth spanning from 2.2 to 6.7 GHz, a system noise of 2.5 quanta, and a saturation power of (−86.5 ± 4.0) dBm. With these characteristics, it is suitable for frequency-multiplexed readout of detector arrays or qubits. Its high saturation power, about 10 dB higher than other reported Josephson-junction-based TWPAs, allows increasing the number of qubits per readout line, or decreasing the intermodulation between frequency-multiplexed qubits, both crucial for scaling up quantum computation.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
Detecting single-photon level signals—carriers of both classical and quantum information—is particularly challenging for low-energy microwave frequency excitations. Here we introduce a superconducting amplifier based on a Josephson junction transmission line. Unlike current standing-wave parametric amplifiers, this traveling wave architecture robustly achieves high gain over a bandwidth of several gigahertz with sufficient dynamic range to read out 20 superconducting qubits. To achieve this performance, we introduce a subwavelength resonant phase-matching technique that enables the creation of nonlinear microwave devices with unique dispersion relations. We benchmark the amplifier with weak measurements, obtaining a high quantum efficiency of 75% (70% including noise added by amplifiers following the Josephson amplifier). With a flexible design based on compact lumped elements, this Josephson amplifier has broad applicability to microwave metrology and quantum optics.
Josephson traveling-wave parametric amplifiers (TWPAs) enable the amplification of weak microwave signals close to the quantum limit with large bandwidth, which has a broad range of applications in superconducting quantum computing and in the operation of single-photon detectors. While the large bandwidth allows for their use in frequency-multiplexed detection architectures, an increased number of readout tones per amplifier puts more stringent requirements on the dynamic range to avoid saturation. Here, we characterize the undesired mixing processes between the different frequency-multiplexed tones applied to a Josephson TWPA, a phenomenon also known as intermodulation distortion. The effect becomes particularly significant when the amplifier is operated close to its saturation power. Furthermore, we demonstrate that intermodulation distortion can lead to significant crosstalk and reduction of fidelity for multiplexed readout of superconducting qubits. We suggest using large detunings between the pump and signal frequencies to mitigate crosstalk. Our work provides insights into the limitations of current Josephson TWPAs and highlights the importance of performing further research on these devices.