Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2401.01663

RF E-field enhanced sensing based on Rydberg-atom-based superheterodyne receiver

Wenguang Yang, Minyong Jing, Hao Zhang, Linjie Zhang, Liantuan Xiao, Suotang Jia

Published Jan 3, 2024• 0 citations
arXivHTMLPDF

Abstract

We present enhanced sensing of radio frequency (RF) electric fields (E-fields) by the combined polarizability of Rydberg atoms and the optimized local oscillator (LO) fields of supergheterodyne receiving. Our modified theoretical model reveals the dependencies of sensitivity of E-field amplitude measurement on the polarizability of Rydberg states and the strength of the LO RF field. The enhanced sensitivity of megahertz(MHz) E-field are demonstrated at an optimal LO field for three different Rydberg states $\rm 43D_{5/2}$, $\rm 60S_{1/2}$, and $\rm 90S_{1/2}$. The sensitivity of 63 MHz for the $\rm 90S_{1/2}$ state reaches 0.96 $μ\rm V/cm/\sqrt{Hz}$ that is about an order of magnitude higher than those already published. This result closely approaches the theoretical sensitivity limit of RF dipole antennas, and indicates the potential for breaking the limit in measuring sub-MHz E-fields. This atomic sensor based on Rydberg Stark effect with heterodyne technique is expected to boost an alternative solution to electric dipole antennas.

DOI
10.48550/arxiv.2401.01663

Related papers

Radio frequency electric field-enhanced sensing based on the Rydberg atom-based superheterodyne receiver

Wenguang Yang, Mingyong Jing, Hao Zhang +3 more

We present enhanced sensing of a radio frequency (RF) electric field (E-field) by the combined polarizability of Rydberg atoms and the optimized local oscillator (LO) field of a superheterodyne receiver. Our modified theoretical model reveals the dependencies of the sensitivity of E-field amplitude measurement on the polarizability of Rydberg states and the strength of the LO field. The enhanced sensitivities of the megahertz (MHz) E-field are demonstrated at the optimal LO field for three different Rydberg states ${\rm 43D}_{5/2}$, ${\rm 60S}_{1/2}$, and ${\rm 90S}_{1/2}$. The sensitivity of 63 MHz for the ${\rm 90S}_{1/2}$ state reaches 9.6 $\times 10^{-5}\rm \,V/m/\sqrt {Hz}$, which is approximately an order of magnitude higher than those already published. This result closely approaches the sensitivity limit of a 1 cm passive dipole antenna without using an impedance matching network. This atomic sensor based on the Rydberg Stark effect with heterodyne technique is expected to boost an alternative solution to electric dipole antennas.

Optics Letters•Apr 22, 2024•18 citations

High-Sensitivity Rydberg Atom-Based Field Sensing Enhancement Using Miniaturized Resonator

Aojie Zhou, Yi Lin, Ruiqi Mao +4 more

High-sensitivity amplitude and frequency detection of microwave electric fields is of significant importance in various fields, including communications, microwave quantum technology, aerospace, medicine, and meteorology. Rydberg atom-based sensors promise traceable standards and high sensitivity for detecting weak electric fields and enhancing sensing sensitivity, mainly by using superheterodyne technology and resonant structures. Detecting high-frequency (HF) band fields with high sensitivity using Rydberg atom sensors is a significant challenge due to the requirement of exciting atoms to extremely high energy states for resonant detection. We demonstrate the off-resonant Rydberg atomic superheterodyne architecture with additional resonators for greatly enhancing the sensing sensitivity to HF band fields. In this approach, we propose a miniaturized square spiral resonator with an electrical size of$0.011~\lambda $at 15.54 MHz. To reduce the electric-field-screening effect of the adsorption of alkali metal atoms, we use a monocrystalline sapphire cesium (Cs) vapor cell. By utilizing the off-resonant alternating current (ac) Stark effect, the initial sensitivity of the Rydberg atom sensor without the resonator is measured to be$10.39~\mu \text {V/cm}\sqrt {\text {Hz}}$at room temperature. With the addition of the miniaturized square spiral resonator, the sensitivity significantly improved to$2.60~\text {nV/cm}\sqrt {\text {Hz}}$, which has been inaccessible so far with atomic sensors. Here, we provide an enhancement of 72 dB, which is three orders of magnitude improvement in sensitivity than when the resonator is not used. This enhancement resonator extends Rydberg atomic high-sensitivity sensing to the HF band and shows great potential, especially in shortwave radio reception.

IEEE Transactions on Antennas and Propagation•Aug 13, 2025•9 citations

Local oscillator port embedded field enhancement resonator for Rydberg atomic heterodyne technique

Kai Yang, Ruiqi Mao, Li He +4 more

Abstract Rydberg atom-based sensors using the atomic heterodyne technique demonstrate prominent performance on sensing sensitivity and thus have significant potential for radar, electronic reconnaissance, and communication applications. Here, we propose a local oscillator (LO) embedded field enhancement resonator to improve the sensitivity and integration of Rydberg atomic heterodyne sensors. In this approach, a vapor cell filled with cesium atoms is placed into the resonance structure for electric (E) field measurements. By integrating parallel-plate waveguide (PPWG) antennas and the resonator, the LO signal can be directly guided to the resonator using coaxial cable instead of the use of external antennas radiating through free space, allowing for a more flexible and practical Rydberg atom-based heterodyne technique. Based on the off-resonant Rydberg atomic heterodyne approach, for a radio frequency (RF) signal at 638 MHz, it is found that the sensitivity is 43 μ V/cm $\sqrt{\text{Hz}}$ Hz in the absence of the resonator, while in the presence of our resonator, the sensitivity is down to 854.36 nV/cm $\sqrt{\text{Hz}}$ Hz , indicating 50 times or 34 dB improvement capacity of the proposed resonator. This type of enhancement resonator is expected to benefit Rydberg atomic heterodyne applications in practical environments.

EPJ Quantum Technology•Jun 26, 2023•27 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Highly Sensitive Measurement of a Megahertz rf Electric Field with a Rydberg-Atom Sensor

Bang Liu, Lihua Zhang, Zong-Kai Liu +6 more

Rydberg atoms have great potential in electric field measurement and have an advantage with a large frequency bandwidth from the kHz to the THz scale. However, the sensitivity for measuring a weak MHz electric field signal is limited by the spectroscopic resolution, because the weak electric field induces only a small perturbation of the population and energy-level shift of the Rydberg atoms. Here, we report highly sensitive measurement of a weak MHz electric field using electromagnetically induced transparency with Rydberg atoms in a thermal atomic system. Using the heterodyne method on a 30-MHz electric field, we successfully measure the minimum electric field strength to be $37.3\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ with a sensitivity up to $\ensuremath{-}65$ dBm/Hz and a linear dynamic range over 65 dB. Additionally, we measure an amplitude-modulated signal and demodulate the signal with a fidelity over 98%. This work extends the sensitivity of atomic sensors for measuring MHz electric fields, which advances atomic electric field-sensing technology.

arXiv:2206.06576•Physical Review Applied•Jul 19, 2022•106 citations

A read-out enhancement for microwave electric field sensing with Rydberg atoms

Harald Kübler, James P. Shaffer

We have shown that Rydberg atoms can be used for high-sensitivity, absolute sensing of radio frequency (RF) electric fields. We achieved a sensitivity of 3 μVcm-1Hz-1/2 for two read-out strategies. Results using a Mach-Zehnder interferometer2 and frequency modulated spectroscopy both achieve similar photon shot noise limited sensitivity. Fundamental limits to the sensitivity of the Rydberg atom-based RF electric field sensing have been addressed. Depending on the spectral resolution of the read-out, either the RF induced transmission line frequency splitting, the Autler-Townes regime, or a change in the on-resonant absorption, the amplitude regime, can be used to determine the RF electric field. Here, we present theoretical results of a 3-photon read-out scheme which enables the Autler-Townes regime of Rydberg atom-based RF electrometry to be extended to lower RF electric field strengths. We show that the residual Doppler shifts can, in principle, be reduced to ~11.8 kHz, on the order of the Rydberg atom natural lindewidths, using the approach.

SPIE Quantum Technologies•May 21, 2018•33 citations
We present enhanced sensing of radio frequency (RF) electric fields (E-fields) by the combined polarizability of Rydberg atoms and the optimized local oscillator (LO) fields of supergheterodyne receiving. Our modified theoretical model reveals the dependencies of sensitivity of E-field amplitude measurement on the polarizability of Rydberg states and the strength of the LO RF field. The enhanced sensitivity of megahertz(MHz) E-field are demonstrated at an optimal LO field for three different Rydberg states 43D5/2\rm 43D_{5/2}43D5/2​, 60S1/2\rm 60S_{1/2}60S1/2​, and 90S1/2\rm 90S_{1/2}90S1/2​. The sensitivity of 63 MHz for the 90S1/2\rm 90S_{1/2}90S1/2​ state reaches 0.96 μV/cm/Hzμ\rm V/cm/\sqrt{Hz}μV/cm/Hz​ that is about an order of magnitude higher than those already published. This result closely approaches the theoretical sensitivity limit of RF dipole antennas, and indicates the potential for breaking the limit in measuring sub-MHz E-fields. This atomic sensor based on Rydberg Stark effect with heterodyne technique is expected to boost an alternative solution to electric dipole antennas.
We present enhanced sensing of a radio frequency (RF) electric field (E-field) by the combined polarizability of Rydberg atoms and the optimized local oscillator (LO) field of a superheterodyne receiver. Our modified theoretical model reveals the dependencies of the sensitivity of E-field amplitude measurement on the polarizability of Rydberg states and the strength of the LO field. The enhanced sensitivities of the megahertz (MHz) E-field are demonstrated at the optimal LO field for three different Rydberg states 43D5/2{\rm 43D}_{5/2}43D5/2​, 60S1/2{\rm 60S}_{1/2}60S1/2​, and 90S1/2{\rm 90S}_{1/2}90S1/2​. The sensitivity of 63 MHz for the 90S1/2{\rm 90S}_{1/2}90S1/2​ state reaches 9.6 ×10−5 V/m/Hz\times 10^{-5}\rm \,V/m/\sqrt {Hz}×10−5V/m/Hz​, which is approximately an order of magnitude higher than those already published. This result closely approaches the sensitivity limit of a 1 cm passive dipole antenna without using an impedance matching network. This atomic sensor based on the Rydberg Stark effect with heterodyne technique is expected to boost an alternative solution to electric dipole antennas.
High-sensitivity amplitude and frequency detection of microwave electric fields is of significant importance in various fields, including communications, microwave quantum technology, aerospace, medicine, and meteorology. Rydberg atom-based sensors promise traceable standards and high sensitivity for detecting weak electric fields and enhancing sensing sensitivity, mainly by using superheterodyne technology and resonant structures. Detecting high-frequency (HF) band fields with high sensitivity using Rydberg atom sensors is a significant challenge due to the requirement of exciting atoms to extremely high energy states for resonant detection. We demonstrate the off-resonant Rydberg atomic superheterodyne architecture with additional resonators for greatly enhancing the sensing sensitivity to HF band fields. In this approach, we propose a miniaturized square spiral resonator with an electrical size of$0.011~\lambda $at 15.54 MHz. To reduce the electric-field-screening effect of the adsorption of alkali metal atoms, we use a monocrystalline sapphire cesium (Cs) vapor cell. By utilizing the off-resonant alternating current (ac) Stark effect, the initial sensitivity of the Rydberg atom sensor without the resonator is measured to be10.39 μV/cmHz10.39~\mu \text {V/cm}\sqrt {\text {Hz}}10.39 μV/cmHz​at room temperature. With the addition of the miniaturized square spiral resonator, the sensitivity significantly improved to2.60 nV/cmHz2.60~\text {nV/cm}\sqrt {\text {Hz}}2.60 nV/cmHz​, which has been inaccessible so far with atomic sensors. Here, we provide an enhancement of 72 dB, which is three orders of magnitude improvement in sensitivity than when the resonator is not used. This enhancement resonator extends Rydberg atomic high-sensitivity sensing to the HF band and shows great potential, especially in shortwave radio reception.
Abstract Rydberg atom-based sensors using the atomic heterodyne technique demonstrate prominent performance on sensing sensitivity and thus have significant potential for radar, electronic reconnaissance, and communication applications. Here, we propose a local oscillator (LO) embedded field enhancement resonator to improve the sensitivity and integration of Rydberg atomic heterodyne sensors. In this approach, a vapor cell filled with cesium atoms is placed into the resonance structure for electric (E) field measurements. By integrating parallel-plate waveguide (PPWG) antennas and the resonator, the LO signal can be directly guided to the resonator using coaxial cable instead of the use of external antennas radiating through free space, allowing for a more flexible and practical Rydberg atom-based heterodyne technique. Based on the off-resonant Rydberg atomic heterodyne approach, for a radio frequency (RF) signal at 638 MHz, it is found that the sensitivity is 43 μ V/cm Hz\sqrt{\text{Hz}}Hz​ Hz in the absence of the resonator, while in the presence of our resonator, the sensitivity is down to 854.36 nV/cm Hz\sqrt{\text{Hz}}Hz​ Hz , indicating 50 times or 34 dB improvement capacity of the proposed resonator. This type of enhancement resonator is expected to benefit Rydberg atomic heterodyne applications in practical environments.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
Rydberg atoms have great potential in electric field measurement and have an advantage with a large frequency bandwidth from the kHz to the THz scale. However, the sensitivity for measuring a weak MHz electric field signal is limited by the spectroscopic resolution, because the weak electric field induces only a small perturbation of the population and energy-level shift of the Rydberg atoms. Here, we report highly sensitive measurement of a weak MHz electric field using electromagnetically induced transparency with Rydberg atoms in a thermal atomic system. Using the heterodyne method on a 30-MHz electric field, we successfully measure the minimum electric field strength to be $37.3\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ with a sensitivity up to $\ensuremath{-}65$ dBm/Hz and a linear dynamic range over 65 dB. Additionally, we measure an amplitude-modulated signal and demodulate the signal with a fidelity over 98%. This work extends the sensitivity of atomic sensors for measuring MHz electric fields, which advances atomic electric field-sensing technology.
We have shown that Rydberg atoms can be used for high-sensitivity, absolute sensing of radio frequency (RF) electric fields. We achieved a sensitivity of 3 μVcm-1Hz-1/2 for two read-out strategies. Results using a Mach-Zehnder interferometer2 and frequency modulated spectroscopy both achieve similar photon shot noise limited sensitivity. Fundamental limits to the sensitivity of the Rydberg atom-based RF electric field sensing have been addressed. Depending on the spectral resolution of the read-out, either the RF induced transmission line frequency splitting, the Autler-Townes regime, or a change in the on-resonant absorption, the amplitude regime, can be used to determine the RF electric field. Here, we present theoretical results of a 3-photon read-out scheme which enables the Autler-Townes regime of Rydberg atom-based RF electrometry to be extended to lower RF electric field strengths. We show that the residual Doppler shifts can, in principle, be reduced to ~11.8 kHz, on the order of the Rydberg atom natural lindewidths, using the approach.