Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2206.06576 · Physical Review Applied

Highly Sensitive Measurement of a Megahertz rf Electric Field with a Rydberg-Atom Sensor

Bang Liu, Lihua Zhang, Zong-Kai Liu, Zheng-Yuan Zhang, Zhi‐Han Zhu, Wei Gao, Guang‐Can Guo, Dong-Sheng Ding, Bao‐Sen Shi

Published Jul 19, 2022• 106 citations
arXivHTMLPDF

Abstract

Rydberg atoms have great potential in electric field measurement and have an advantage with a large frequency bandwidth from the kHz to the THz scale. However, the sensitivity for measuring a weak MHz electric field signal is limited by the spectroscopic resolution, because the weak electric field induces only a small perturbation of the population and energy-level shift of the Rydberg atoms. Here, we report highly sensitive measurement of a weak MHz electric field using electromagnetically induced transparency with Rydberg atoms in a thermal atomic system. Using the heterodyne method on a 30-MHz electric field, we successfully measure the minimum electric field strength to be $37.3\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ with a sensitivity up to $\ensuremath{-}65$ dBm/Hz and a linear dynamic range over 65 dB. Additionally, we measure an amplitude-modulated signal and demodulate the signal with a fidelity over 98%. This work extends the sensitivity of atomic sensors for measuring MHz electric fields, which advances atomic electric field-sensing technology.

DOI
10.1103/physrevapplied.18.014045

Related papers

Super low-frequency electric field measurement based on Rydberg atoms

Ling Li, Yuechun Jiao, Jinlian Hu +4 more

We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.

Optics Express•Aug 9, 2023•43 citations

Weak electric-field detection with sub-1 Hz resolution at radio frequencies using a Rydberg atom-based mixer

Joshua A. Gordon, Matthew T. Simons, Abdulaziz H. Haddab +1 more

Rydberg atoms have been used for measuring radio-frequency (RF) electric (E)-fields due to their strong dipole moments over the frequency range of 500 MHz-1 THz. For this, electromagnetically induced transparency (EIT) within the Autler-Townes (AT) regime is used such that the detected E-field is proportional to AT splitting. However, for weak E-fields AT peak separation becomes unresolvable thus limiting the minimum detectable E-field. Here, we demonstrate using the Rydberg atoms as an RF mixer for weak E-field detection well below the AT regime with frequency discrimination better than 1 Hz resolution. A heterodyne detection scenario with two E-fields incident on a vapor cell filled with cesium atoms is used. One E-field at 19.626000 GHz drives the 34D5/2 → 35P3/2 Rydberg transition and acts as a local oscillator (LO) and a second signal E-field (Sig) of interest is at 19.626090 GHz. In the presence of the LO, the Rydberg atoms naturally down convert the Sig field to a 90 kHz intermediate frequency (IF) signal. This IF signal manifests as an oscillation in the probe laser intensity through the Rydberg vapor and is easily detected with a photodiode and lock-in amplifier. In the configuration used here, E-field strength down to ≈ 46 μV/m ± 2 μV/m were detected with a sensitivity of ≈ 79 μVm−1Hz−1/2. Furthermore, neighboring fields 0.1 Hz away and equal in strength to Sig could be discriminated without any leakage into the lock-in signal. For signals 1 Hz away and as high as +60 dB above Sig, leakage into the lock-in signal could be kept below -3 dB.

arXiv:1903.09712•AIP Advances•Apr 1, 2019•179 citations

Measurement of low-frequency electric field waveform by Rydberg atom-based sensor

Xuechao Zhang, Jia-Hui Qiao, Yao Liu +6 more

The high polarizability of Rydberg atoms enables the multi-parameters measurement of electromagnetic fields. In this paper, we report on an atomic antenna based on Rydberg atoms in a room temperature vapor cell. The EIT is a destructive interference spectroscopy with a narrow linewidth and can be used to detect small electric fields through Autler-Townes splitting or Stark shifts. In our experiments, we employ cascade-type two-photon excitation electromagnetically induced transparency (EIT) spectroscopy to measure the shift of the Rydberg energy level. We introduce a low-frequency electric field (~kHz frequency) using a built-in electrode technique in the cesium cell. The interaction between the Rydberg atom and electric field induces the Stark shifts, where the amplitude of the electric field is converted into corresponding two-photon detuning by the EIT effect. Furthermore, the amplitude of the low-frequency electric field is converted into an intensity signal of EIT probe beam. Under weak field conditions, it is an approximate linear relationship between EIT transmission signal and input electric field amplitude, enabling measurement of waveform, amplitude, and frequency. We have demonstrated optical measurements of low-frequency electric field using Rydberg atoms. By increasing the power of probe beam and coupling beam, the EIT can increase the response bandwidth from ~MHz to hundreds of MHz. This provides a scalable approach for measuring high-frequency electric fields.

Acta Physica Sinica•Jan 1, 2024•4 citations

Shortwave Ultrahigh-Sensitivity Rydberg Atomic Electric Field Sensing Based on a Subminiature Resonator

Ruiqi Mao, Yi Lin, Aojie Zhou +2 more

Rydberg atomic electric field sensors have attracted the attention of international researchers due to their powerful electric field measurement capabilities. Especially in the shortwave (SW) frequency band (3–30 MHz), using only millimeter-level sensors to receive SW signals is undoubtedly attractive. However, due to the extremely difficult excitation of the Rydberg atoms that resonate with the SW frequency, the sensitivity of the Rydberg atoms SW measurement is low. Here, we report that a method to improve the SW sensitivity by using an SW resonator, which is extremely small in electrical size ($0.0043\lambda \times 0.0035\lambda \times 0.007\lambda $), can achieve continuous resonant frequency coverage from 9.365 to 10.223 MHz and can increase the sensitivity of electric field measurement by a factor of 8633. In the state of far off-resonant, we have achieved a detectable field strength as low as$2.41~\mu $V/m with a sensitivity of$1.71~\mu $V/mHz$^{1/2}$using the heterodyne Rydberg atom-based mixer method, which realizes ultrahigh-sensitivity measurement of SWs. In addition, for the first time outside the laboratory, we directly received an amplitude-modulated broadcast signal with 880 km (the straight-line distance between Changsha and Baoji) at 9.81 MHz in the form of a subminiature resonator combined with a Rydberg field probe (RFP), which verified the powerful ability of this sensing scheme.

IEEE Transactions on Antennas and Propagation•Aug 13, 2024•17 citations

Continuously tunable radio frequency electrometry with Rydberg atoms

Jinlian Hu, Huaqiang Li, Rong Song +4 more

We demonstrate a continuously tunable electric field measurement based on the far off-resonant AC stark effect in a Rydberg atomic vapor cell. In this configuration, a strong far off-resonant field, denoted as a local oscillator (LO) field, acts as a gain to shift the Rydberg level to a high sensitivity region. An incident weak signal field with a few hundreds of kHz difference from the LO field is mixed with the LO field in the Rydberg system to generate an intermediate frequency signal, which is read out by Rydberg electromagnetically induced transparency (Rydberg-EIT) spectroscopy. Not like resonant EIT-Autler–Townes spectra, we realize the electric field measurement of the signal frequency from 2 to 5 GHz using a single Rydberg state. The detectable field strength is down to 2.25 μV/cm with sensitivity of the electrometry 712 nV cm−1 Hz−1/2, and a linear dynamic range is over 65 dB. The detectable field strength is comparable with a resonant microwave-dressed Rydberg heterodyne receiver using the same system, which is 0.96 μV/cm with sensitivity of 304 nV cm–1 Hz−1/2. We also show the system has an inherent polarization selectivity feature. Our method can provide high sensitivity of electric field measurement and be extended to arbitrary frequency measurements.

arXiv:2201.10068•Applied Physics Letters•Jul 4, 2022•97 citations

Broadband Heterodyne Microwave Detection using Rydberg Atoms with High Sensitivity

Hsuan-Jui Su, Shao-Cheng Fang, Ting-An Li +3 more

We present a Rydberg atom-based microwave electric field sensor that achieves extended dynamic range and enhanced sensitivity across a broad bandwidth. By characterizing the Autler-Townes (AT) splitting induced by a single-tone microwave field, we demonstrate a spectroscopic method that simultaneously extracts both the microwave frequency and electric field strength directly from the splitting pattern. We implement dual-tone heterodyne detection, achieving a minimum detectable field strength on the order of uV/cm and a sensitivity in the sub-uV/cm/Hz^1/2 regime, while extending the operational bandwidth up to 3 GHz. Through systematic characterization of frequency and power dependencies, we identify optimal operating conditions to minimize power broadening in the resonant AT regime and maximize sensitivity in the far-off-resonance AC Stark regime. The resulting platform combines high sensitivity, broad bandwidth, and a dynamic range of approximately 90 dB, establishing Rydberg atoms as practical sensors for precision electric field metrology.

physics.atom-phCross-listedarXiv:2601.19305•Jan 28, 2026•0 citations
Rydberg atoms have great potential in electric field measurement and have an advantage with a large frequency bandwidth from the kHz to the THz scale. However, the sensitivity for measuring a weak MHz electric field signal is limited by the spectroscopic resolution, because the weak electric field induces only a small perturbation of the population and energy-level shift of the Rydberg atoms. Here, we report highly sensitive measurement of a weak MHz electric field using electromagnetically induced transparency with Rydberg atoms in a thermal atomic system. Using the heterodyne method on a 30-MHz electric field, we successfully measure the minimum electric field strength to be 37.3\ensuremathμV/cm37.3\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}/\mathrm{cm}37.3\ensuremathμV/cm with a sensitivity up to \ensuremath−65\ensuremath{-}65\ensuremath−65 dBm/Hz and a linear dynamic range over 65 dB. Additionally, we measure an amplitude-modulated signal and demodulate the signal with a fidelity over 98%. This work extends the sensitivity of atomic sensors for measuring MHz electric fields, which advances atomic electric field-sensing technology.
We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.
Rydberg atoms have been used for measuring radio-frequency (RF) electric (E)-fields due to their strong dipole moments over the frequency range of 500 MHz-1 THz. For this, electromagnetically induced transparency (EIT) within the Autler-Townes (AT) regime is used such that the detected E-field is proportional to AT splitting. However, for weak E-fields AT peak separation becomes unresolvable thus limiting the minimum detectable E-field. Here, we demonstrate using the Rydberg atoms as an RF mixer for weak E-field detection well below the AT regime with frequency discrimination better than 1 Hz resolution. A heterodyne detection scenario with two E-fields incident on a vapor cell filled with cesium atoms is used. One E-field at 19.626000 GHz drives the 34D5/2 → 35P3/2 Rydberg transition and acts as a local oscillator (LO) and a second signal E-field (Sig) of interest is at 19.626090 GHz. In the presence of the LO, the Rydberg atoms naturally down convert the Sig field to a 90 kHz intermediate frequency (IF) signal. This IF signal manifests as an oscillation in the probe laser intensity through the Rydberg vapor and is easily detected with a photodiode and lock-in amplifier. In the configuration used here, E-field strength down to ≈ 46 μV/m ± 2 μV/m were detected with a sensitivity of ≈ 79 μVm−1Hz−1/2. Furthermore, neighboring fields 0.1 Hz away and equal in strength to Sig could be discriminated without any leakage into the lock-in signal. For signals 1 Hz away and as high as +60 dB above Sig, leakage into the lock-in signal could be kept below -3 dB.
The high polarizability of Rydberg atoms enables the multi-parameters measurement of electromagnetic fields. In this paper, we report on an atomic antenna based on Rydberg atoms in a room temperature vapor cell. The EIT is a destructive interference spectroscopy with a narrow linewidth and can be used to detect small electric fields through Autler-Townes splitting or Stark shifts. In our experiments, we employ cascade-type two-photon excitation electromagnetically induced transparency (EIT) spectroscopy to measure the shift of the Rydberg energy level. We introduce a low-frequency electric field (~kHz frequency) using a built-in electrode technique in the cesium cell. The interaction between the Rydberg atom and electric field induces the Stark shifts, where the amplitude of the electric field is converted into corresponding two-photon detuning by the EIT effect. Furthermore, the amplitude of the low-frequency electric field is converted into an intensity signal of EIT probe beam. Under weak field conditions, it is an approximate linear relationship between EIT transmission signal and input electric field amplitude, enabling measurement of waveform, amplitude, and frequency. We have demonstrated optical measurements of low-frequency electric field using Rydberg atoms. By increasing the power of probe beam and coupling beam, the EIT can increase the response bandwidth from ~MHz to hundreds of MHz. This provides a scalable approach for measuring high-frequency electric fields.
Rydberg atomic electric field sensors have attracted the attention of international researchers due to their powerful electric field measurement capabilities. Especially in the shortwave (SW) frequency band (3–30 MHz), using only millimeter-level sensors to receive SW signals is undoubtedly attractive. However, due to the extremely difficult excitation of the Rydberg atoms that resonate with the SW frequency, the sensitivity of the Rydberg atoms SW measurement is low. Here, we report that a method to improve the SW sensitivity by using an SW resonator, which is extremely small in electrical size ($0.0043\lambda \times 0.0035\lambda \times 0.007\lambda $), can achieve continuous resonant frequency coverage from 9.365 to 10.223 MHz and can increase the sensitivity of electric field measurement by a factor of 8633. In the state of far off-resonant, we have achieved a detectable field strength as low as$2.41~\mu $V/m with a sensitivity of$1.71~\mu V/mHzV/mHzV/mHz^{1/2}$using the heterodyne Rydberg atom-based mixer method, which realizes ultrahigh-sensitivity measurement of SWs. In addition, for the first time outside the laboratory, we directly received an amplitude-modulated broadcast signal with 880 km (the straight-line distance between Changsha and Baoji) at 9.81 MHz in the form of a subminiature resonator combined with a Rydberg field probe (RFP), which verified the powerful ability of this sensing scheme.
We demonstrate a continuously tunable electric field measurement based on the far off-resonant AC stark effect in a Rydberg atomic vapor cell. In this configuration, a strong far off-resonant field, denoted as a local oscillator (LO) field, acts as a gain to shift the Rydberg level to a high sensitivity region. An incident weak signal field with a few hundreds of kHz difference from the LO field is mixed with the LO field in the Rydberg system to generate an intermediate frequency signal, which is read out by Rydberg electromagnetically induced transparency (Rydberg-EIT) spectroscopy. Not like resonant EIT-Autler–Townes spectra, we realize the electric field measurement of the signal frequency from 2 to 5 GHz using a single Rydberg state. The detectable field strength is down to 2.25 μV/cm with sensitivity of the electrometry 712 nV cm−1 Hz−1/2, and a linear dynamic range is over 65 dB. The detectable field strength is comparable with a resonant microwave-dressed Rydberg heterodyne receiver using the same system, which is 0.96 μV/cm with sensitivity of 304 nV cm–1 Hz−1/2. We also show the system has an inherent polarization selectivity feature. Our method can provide high sensitivity of electric field measurement and be extended to arbitrary frequency measurements.
We present a Rydberg atom-based microwave electric field sensor that achieves extended dynamic range and enhanced sensitivity across a broad bandwidth. By characterizing the Autler-Townes (AT) splitting induced by a single-tone microwave field, we demonstrate a spectroscopic method that simultaneously extracts both the microwave frequency and electric field strength directly from the splitting pattern. We implement dual-tone heterodyne detection, achieving a minimum detectable field strength on the order of uV/cm and a sensitivity in the sub-uV/cm/Hz^1/2 regime, while extending the operational bandwidth up to 3 GHz. Through systematic characterization of frequency and power dependencies, we identify optimal operating conditions to minimize power broadening in the resonant AT regime and maximize sensitivity in the far-off-resonance AC Stark regime. The resulting platform combines high sensitivity, broad bandwidth, and a dynamic range of approximately 90 dB, establishing Rydberg atoms as practical sensors for precision electric field metrology.