The presence of amorphous oxide layers can significantly affect the coherent time of superconducting qubits due to their high dielectric loss. Typically, the surface oxides of superconductor films exhibit lossy and unstable behavior when exposed to air. To increase the coherence time, it is essential for qubits to have stable and low dielectric loss oxides, either as barrier or passivation layers. In this study, we highlight the robust and stable nature of an amorphous tantalum oxide layer formed on α-Ta (110) film by employing chemical and structural analyses. Such kind of oxide layer forms in a self-limiting process on the surface of α-Ta (110) film in piranha solution, yielding stable thickness and steady chemical composition. Quarter-wavelength coplanar waveguide resonators are made to study the loss of this oxide. One resonator has a Qi of 3.0 × 106 in the single photon region. The Qi of most devices are higher than 2.0 × 106. Moreover, most of them are still over 1 × 106 even after exposed to air for months. Based on these findings, we propose an all-tantalum superconducting qubit utilizing such oxide as passivation layers, which possess low dielectric loss and improved stability.
The presence of amorphous oxide layers can significantly affect the coherent time of superconducting qubits due to their high dielectric loss. Typically, the surface oxides of superconductor films exhibit lossy and unstable behavior when exposed to air. To increase the coherence time, it is essential for qubits to have stable and low dielectric loss oxides, either as barrier or passivation layers. In this study, we highlight the robust and stable nature of an amorphous tantalum oxide layer formed on α-Ta (110) film by employing chemical and structural analyses. Such kind of oxide layer forms in a self-limiting process on the surface of α-Ta (110) film in piranha solution, yielding stable thickness and steady chemical composition. Quarter-wavelength coplanar waveguide resonators are made to study the loss of this oxide. One resonator has a Qi of 3.0 × 106 in the single photon region. The Qi of most devices are higher than 2.0 × 106. Moreover, most of them are still over 1 × 106 even after exposed to air for months. Based on these findings, we propose an all-tantalum superconducting qubit utilizing such oxide as passivation layers, which possess low dielectric loss and improved stability.
Abstract The dielectric loss of amorphous oxide layers is a major limiting factor for the coherent time of superconducting qubits. Usually, the surface oxides of superconductor film are lossy and unstable in air. To increase the coherence time, it is essential for qubits to have stable and low dielectric loss oxides, either as barrier or passivation layers. Here, we demonstrate that a kind of amorphous tantalum oxide on α-Ta (110) film is robust and stable by means of chemical and structural analysis. Such kind of oxide layer forms in a self-limiting process on the surface of α-Ta (110) film in piranha solution, yielding stable thickness and steady chemical composition. Quarter-wavelength coplanar waveguide resonators are made to study the loss of this oxide. One fresh resonator have a Qi of 3.0×106 in the single photon region. The Qi of most devices are higher than 2.0×106. And most of them are still over one million even after exposed to air for months. Based on these findings, we propose an all-tantalum superconducting qubit utilizing such oxide as passivation layers, which possess low dielectric loss and improved stability.
Superconducting qubits have become one of the leading contenders in making quantum computing a reality because of their robustness and scalability [1]. Replacing the widely adopted Al and Nb, Ta has become the most promising candidate material for superconducting qubit fabrication due to its exceptionally enhanced thermal relaxation time (i.e., T1 time). This time can exceed 0.3 milliseconds which is three orders of magnitude higher than the previous methods [2]. However, during the fabrication process, exposure of tantalum to air leads to the formation of an amorphous surface oxide layer. The presence of this oxide layer can affect the superconducting properties of the tantalum film and, hence, the performance of the qubit. This native amorphous oxidized surface results in a dielectric loss through an energy reduction mechanism called a two-level system caused by structural and chemical defects [3]. Although Ta exhibits superior performance, particularly T1 time, compared to other superconducting materials, its value remains insufficient for quantum processor hardware. Therefore, understanding the structural and chemical profile of the native amorphous surface of the oxides for superconducting qubits is required to optimize their performance. In this study, we employed scanning transmission electron microscopy (STEM) with a combination of electron energy loss spectroscopy (EELS) and four-dimensional STEM (4D-STEM) to probe the electronic and crystallographic structure of the local surface areas. Furthermore, to circumvent the spectral and diffractometric profiles that overlap as a function of depth position caused by electron beam broadening, we applied Multivariate curve resolution (MCR) analysis that can separate complex mixtures into their basis components. In the subsequent experiments, we investigated the surface morphology of (110)-oriented α-Ta film grown on an A-plane sapphire substrate using scanning electron microscopy (SEM) (Figure 1a), and high-angle annular dark-field (HAADF) STEM imaging (Figure 1b and 1c). We found that the surface of the Ta film is bumpy, and made of an amorphous material with a thickness of about 3 nm. The film exhibits a columnar structure along the [001] growth direction. EELS fine structure analysis reveals that most of the amorphous regions are in the Ta2O5 phase (Figure 2a and 2b). By extracting valuable basis components of O-K fine structures, we were able to quantify the concentration of the chemical species with Å-scale at the interface using MCR analysis. Specifically, a depth dependent composition variation, especially that of oxygen concentration, was observed. We further investigated amorphous oxide films and interfaces with 4D-STEM based fluctuation electron microscopy. (Figure 2c and 2d) We obtained results that were consistent with the chemical profiles obtained from the O-K edge EELS mapping. We also revealed the crystalline ordering information of each chemical species. The detailed descriptions of the results will be presented at the conference. These STEM analysis findings were supported by first-principles calculations of oxygen concentration changes and phase formation energies. Overall, our research provides important insights into the formation and properties of the native amorphous surface oxides of a superconducting qubit tantalum film, which is critical for the development of next-generation quantum computing technologies [4]. Surface morphology of α-Ta film on A-plane sapphire. (a) Top-view SEM image. Cross-sectional HAADF STEM images at (b) low and (c) high magnification. To protect the film surface during the FIB process, the coating layer is on top of the bumpy surface of the Ta film with a thin native oxidized layer of gray contrast. Crystal orientation is indicated on the left-bottom corner in (a) and (c) for the top-view and cross-sectional view images, respectively. STEM-EELS and 4D-STEM analysis across the interfaces between the native oxidized amorphous and the crystalline Ta film. (a) HAADF STEM image of the region-of-interest, simultaneously acquired with EELS mapping. (b) Representative EELS spectra of O-K edge fine structures and (c, d) electron diffraction patterns from the native oxidized amorphous region (green) and the crystalline Ta film region (blue).
We demonstrate a substantial reduction in two-level system loss in tantalum coplanar waveguide resonators fabricated on high-resistivity silicon substrates through the use of an ultrathin titanium sacrificial layer. A 0.2nm titanium film, deposited atop pre-sputtered α-tantalum, acts as a solid-state oxygen getter that chemically modifies the native Ta oxide at the metal-air interface. After device fabrication, the titanium layer is removed using buffered oxide etchant, leaving behind a chemically reduced Ta oxide surface. Subsequent high-vacuum annealing further suppresses two-level system loss. Resonators treated with this process exhibit internal quality factors Qi exceeding an average of 1.5 million in the single-photon regime across ten devices, over three times higher than otherwise identical devices lacking the titanium layer. These results highlight the critical role of interfacial oxide chemistry in superconducting loss and reinforce atomic-scale surface engineering as an effective approach to improving coherence in tantalum-based quantum circuits. The method is compatible with existing fabrication workflows applicable to tantalum films, offering a practical route to further extending T1 lifetimes in superconducting qubits.
Superconducting qubits are among the most advanced platforms for quantum information, offering potential scalability and compatibility with standard device fabrication techniques [1-5]. Among the materials investigated for superconducting qubits, Tantalum (Ta) has emerged as a compelling candidate due to its self-terminating stoichiometric surface oxide and chemical resistance to harsh post-fabrication processes. Efforts to mitigate surface loss by treating the surface oxides and utilizing high-resistivity silicon substrates have led to Ta-based qubits with lifetime and coherence times exceeding 1 ms [3]. Guided by these successes in reducing dielectric loss in Ta-based devices, we are interested in exploring material engineering approaches that enhance the superconducting gap. Alloying Ta with another element to enhance the superconducting performance expands the range of viable material candidates available to tackle different loss channels in superconducting circuits [1]. Recently, we explore superconducting gap engineering in Ta-based devices as a powerful strategy for expanding the range of suitable host materials. By alloying 20 at.% hafnium (Hf) into Ta thin films, we achieve a superconducting transition temperature (Tc) of 6.09 K as observed in direct current (DC) transport measurements, reflecting an increase in the superconducting gap. Here we demonstrate an approach for controlling varying deposition conditions to control film orientation and transport properties of Ta and Ta-Hf alloy thin films. We investigate the microstructure and composition distribution of the thin films by using high-resolution scanning transmission electron microscopy (STEM) with super-X EDS system (no serious beam damage issue [6-8]). Our structural analysis using TEM diffraction and STEM verifies the BCC structure across all the films (Figure 1), and direct current (DC) transport measurements reveal a 40% enhancement in Tc relative to undoped Ta (Tc=4.3 K). We monitored oxide growth over an 18-day period following film deposition to better understand how Hf incorporation influences surface oxides. In both Ta and Hf spectra, the fraction of fully oxidized (Ta2O5 and HfO2) states gradually increased during the 18-day exposure, indicating progressive surface oxidation. To estimate the surface oxide thickness, we use cross-sectional TEM/EDS mapping (Figure 1c). The analysis reveals that the oxide thickness for the 1 ks Ta-Hf alloy film is approximately 3 nm in thickness, comparable to the 3 nm oxide observed on native Ta [2]. For the 2 ks Ta-Hf film, the oxide thickness increases slightly to about 4 nm (Figure 1). The measured surface loss tangent of the Ta-Hf alloy remains comparable to that of native Ta. This result suggests that the surface oxide of the Ta-Hf alloy, which contains a measurable fraction of HfOx, does not introduce additional dielectric loss. By engineering the alloy composition and film deposition, this study achieves both improved superconducting properties and compatibility with fabrication processes. These findings show that material doping and alloying can strategically expand the suite of viable materials for superconducting quantum devices. This approach provides a pathway for tailoring material properties to support the next generation of quantum technologies and offers broad relevance to researchers in materials science, quantum information, and device engineering [9]. STEM images on cross sections of 1 ks (a) and 2 ks (b) Ta-Hf thin films, both films were sputtered at 750 ◦C. (c) Cross-sectional EDS elemental mapping on Ta-Hf. Cross-sectional EDS mapping Ta (blue) and Hf (orange) confirmed a uniform Ta-Hf alloy with the Ta to Hf atomic ratios for the bulk to be (83% : 17%). The oxygen (red) map reveals a surface oxide layer with the estimated surface oxide thickness of around 4 nm. The 1 ks Ta-Hf film exhibits an oxide thickness of approximately 3 nm, similar to that of native Ta. The EDS resolution limit is 0.5 atomic percent.
Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide.
We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.
Tantalum is a promising platform for superconducting quantum circuits, yet coherence times remain limited by dielectric losses from interfacial two-level systems (TLS), exacerbated by native oxide regrowth. Here, we implement molecular surface passivation using self-assembled organic monolayers on freshly etched tantalum and silicon in coplanar waveguide resonators. Surface characterization by contact angle, XPS, FTIR and TEM confirm the formation of ordered, nanometer-thick films that suppress oxide formation. Microwave measurements in the ~5-9 GHz range reveal internal quality factors up to 1.8x10^6 in the single-photon regime at 100 mK, representing a ~140% improvement over untreated devices with native oxide. Power and temperature dependent measurements attribute this enhancement to reduced TLS-induced losses. These results demonstrate that molecular passivation effectively engineers low-loss interfaces and provides a scalable route toward high-coherence superconducting quantum devices.