A number of modern millimeter, sub-millimeter, and far-infrared detectors are read out using superconducting microwave (1-10GHz) resonators. The main detector technologies are Transition Edge Sensors, read out using Microwave SQUID Multiplexers (µmux) and Microwave Kinetic Inductance Detectors. In these readout schemes, sky signal is encoded as resonance frequency changes. One way to interrogate these superconducting resonators is to calibrate the probe tone phase such that any sky signal induced frequency shifts from the resonators show up primarily as voltage changes in only one of the two quadratures of the interrogation tone. However, temperature variations in the operating environment produce phase drifts that degrade the phase calibration and can source low frequency noise in the final detector time ordered data if left to drift too far from optimal calibration. We present a method for active software monitoring of the time delay through the system which could be used to feedback on the resonator probe tone calibration angle or to apply an offline cleaning. We implement and demonstrate this monitoring method using the SLAC Microresonator RF Electronics on a 65 channel µmux chip from NIST.
A number of modern millimeter, sub-millimeter, and far-infrared detectors are read out using superconducting microwave (1-10GHz) resonators. The main detector technologies are Transition Edge Sensors, read out using Microwave SQUID Multiplexers (µmux) and Microwave Kinetic Inductance Detectors. In these readout schemes, sky signal is encoded as resonance frequency changes. One way to interrogate these superconducting resonators is to calibrate the probe tone phase such that any sky signal induced frequency shifts from the resonators show up primarily as voltage changes in only one of the two quadratures of the interrogation tone. However, temperature variations in the operating environment produce phase drifts that degrade the phase calibration and can source low frequency noise in the final detector time ordered data if left to drift too far from optimal calibration. We present a method for active software monitoring of the time delay through the system which could be used to feedback on the resonator probe tone calibration angle or to apply an offline cleaning. We implement and demonstrate this monitoring method using the SLAC Microresonator RF Electronics on a 65 channel µmux chip from NIST.
We describe the newest generation of the SLAC Microresonator RF (SMuRF) electronics, a warm digital control and readout system for microwave-frequency resonator-based cryogenic detector and multiplexer systems, such as microwave superconducting quantum interference device multiplexers (μmux) or microwave kinetic inductance detectors. Ultra-sensitive measurements in particle physics and astronomy increasingly rely on large arrays of cryogenic sensors, which in turn necessitate highly multiplexed readout and accompanying room-temperature electronics. Microwave-frequency resonators are a popular tool for cryogenic multiplexing, with the potential to multiplex thousands of detector channels on one readout line. The SMuRF system provides the capability for reading out up to 3328 channels across a 4-8 GHz bandwidth. Notably, the SMuRF system is unique in its implementation of a closed-loop tone-tracking algorithm that minimizes RF power transmitted to the cold amplifier, substantially relaxing system linearity requirements and effective noise from intermodulation products. Here, we present a description of the hardware, firmware, and software systems of the SMuRF electronics, comparing achieved performance with science-driven design requirements. In particular, we focus on the case of large-channel-count, low-bandwidth applications, but the system has been easily reconfigured for high-bandwidth applications. The system described here has been successfully deployed in lab settings and field sites around the world and is baselined for use on upcoming large-scale observatories.
The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.
Microwave kinetic inductance detectors (MKIDs) operate through means of a superconducting resonator that changes resonant frequency and quality factor when incident photons are absorbed in the superconducting material. Incident power on MKIDs is determined by reading out the phase and amplitude of a tone injected into each detector. However, if the incident power on an MKID changes too drastically and the resonant frequency moves too far from the probe tone, amplitude information becomes useless and the detector is effectively out of commission until a VNA sweep is used to relocate resonances. Here we present the designs and preliminary results of a tone-tracking firmware that uses phase information to maintain an on-resonance probe tone at all times, removing the need for time-intensive VNA sweeps during observations and effectively maximizing the dynamic range of MKIDs. We will conclude with a discussion on future NASA missions that hope implement this tone-tracking design.
Transition Edge Sensors (TESs) are highly sensitive cryogenic detectors widely used in astronomy, high-energy physics and nuclear radiation detection. As TES is increasingly deployed in large-scale arrays to improve sensitivity and effective collecting area, multiplexed readout becomes essential for reducing system complexity. Microwave SQUID multiplexing (μMUX) technology combining superconducting resonators with radio-frequency superconducting quantum interference devices (RF-SQUIDs), represents a state-of-the-art solution. In this work, a room-temperature readout prototype for TES μMUX readout was designed. The system features a scalable two-stage architecture, including a highly integrated, chassis-independent front-end signal processing module and back-end event-reconstruction module. A high-frequency-resolution frequency-comb signal generation method with real-time, per-tone frequency and phase tunability was developed. In addition, optimization of the firmware implementation effectively overcomes the computational-resource bottleneck of the Field Programmable Gate Array (FPGA). The prototype supports autonomous frequency sweeping, parameter diagnostics, and online event reconstruction. Self-test shows S 21 phase noise better than −110 dBc/Hz at −30 dBm, remaining stable with increasing channel count. Joint tests with a μMUX cryogenic system successfully captured the RF-SQUID response and achieved an equivalent noise current of 44 pA/√Hz referred to the TES, validating the prototype as a practical solution of the room-temperature system for TES μMUX readout.
Superconducting transition-edge sensors (TESs) with high sensitivity can detect electromagnetic wave radiations from millimeter/submillimeter, optical to x/γ rays, and have been successfully used in many fields. To improve detection efficiency and sensitivity, large-scale TES arrays are required in combination with multiplexing readout electronics. Compared to other multiplexing schemes, microwave SQUID multiplexing (μMUX), consisting of high-quality microwave superconducting resonators and RF SQUIDs, is most suitable since it provides a wider bandwidth (GHz) and consequently higher multiplexing factor. We designed two types of circuits with different mutual inductances (MT) between the resonator and the RF SQUID: 2.3 pH for the weak-coupling channel and 6.5 pH for the strong- coupling channel. The resonator and RF SQUID washers made of 150 nm Nb are first fabricated by magnetron-sputtering and reactive ion etching (RIE), followed by deposition of Nb/Al-AlOx/Nb trilayer and definition of the Josephson junctions of the RF SQUIDs. This work presents a μMUX demonstration chip with five channels with Q1values of 787 and 3626, and the measured frequency shifts (Δfpp) of ∼500 kHz and 4 MHz for the weak- and strong-coupling channels, respectively. The open-loop equivalent noise current, obtained from the measured phase noise and resonator responsivity, is ∼80 pA/ √Hz with the strong-coupling channel.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.