Optical quantum technologies such as quantum sensing, quantum cryptography and quantum computation all utilize properties of non-classical light, such as precise photon-number and entangled photon-pair states, to surpass technologies based on the classical light. A common route for obtaining heralded single photons is spontaneous four-wave mixing in optical fibers, allowing for a well-defined spatial mode, for high efficiency integration into optical fiber networks. These fibers are typically pumped using large, commercial, pulsed lasers requiring high-power (~10 W) pump lasers and are limited to ~MHz repetition rate. Here we propose a cost- efficient, compact and mobile alternative. Photon pairs at 660 nm and 960 nm will be created using four-wave mixing in commercial birefringent optical fiber, pumped using transform limited picosecond pulses with GHz repetition rates derived from a 785 nm CW laser diode using cavity-enhanced optical frequency comb generation. The pulses are predicted to have average power of 275 mW, a peak power of >40 W, and predicted photon yield of >2000 pairs detected per second. This design will be later utilized to implement a quantum illumination scheme based on a coincidence count between idler and signal photons -- instead of joint measurement between signal and idler. This will allow for quantum advantage over classic LIDAR without the requirement for maintaining an interferometric stability in free space.
Optical quantum technologies such as quantum sensing, quantum cryptography and quantum computation all utilize properties of non-classical light, such as precise photon-number and entangled photon-pair states, to surpass technologies based on the classical light. A common route for obtaining heralded single photons is spontaneous four-wave mixing in optical fibers, allowing for a well-defined spatial mode, for high efficiency integration into optical fiber networks. These fibers are typically pumped using large, commercial, pulsed lasers requiring high-power (~10 W) pump lasers and are limited to ~MHz repetition rate. Here we propose a cost- efficient, compact and mobile alternative. Photon pairs at 660 nm and 960 nm will be created using four-wave mixing in commercial birefringent optical fiber, pumped using transform limited picosecond pulses with GHz repetition rates derived from a 785 nm CW laser diode using cavity-enhanced optical frequency comb generation. The pulses are predicted to have average power of 275 mW, a peak power of >40 W, and predicted photon yield of >2000 pairs detected per second. This design will be later utilized to implement a quantum illumination scheme based on a coincidence count between idler and signal photons -- instead of joint measurement between signal and idler. This will allow for quantum advantage over classic LIDAR without the requirement for maintaining an interferometric stability in free space.
The field of quantum optics offers the intriguing possibility of developing new, potentially ground-breaking technologies based on the laws of quantum physics. Single quanta of light, called photons, are at the heart of many such quantum optical technologies. They can serve, for example, as information carriers in quantum cryptography and in quantum-information processing. If such applications are to fulfill their enormous potential, it is essential to have sources available that provide photons in the required quantum states. An established way of generating states of single photons is based on photon-pair sources. In this approach, the detection of one photon of a pair heralds the presence of the partner photon, which can then be further processed. However, to generate heralded photons in pure quantum states, specific conditions have to be met, making the design and implementation of such sources challenging. This thesis presents two new photon-pair sources that allow the heralded generation of single photons with high purity. Both sources are based on optical fiber, which allows high collection efficiencies for the generated states and opens the possibility of easy integration into modern-day fiber networks. Chapter 1 provides an introduction to quantum optical technologies and gives a short overview of current approaches to generate pure single photons. Chapter 2 presents the basic theory on which the experimental work presented in Chapters 3 and 4 is based. It explains the concept of a spectrally broad single photon and how photon purity can be tested using Hong-Ou-Mandel (HOM) interference. Subsequently, the properties of photon-pair states and the heralded generation of single photons from such states are discussed. It is shown that for a heralded photon to be pure, the original photon pair has to be in a factorable state, that is, free of any correlations. The introduced theory is then applied to spontaneous four-wave mixing (SFWM) in optical fibers, a nonlinear process that allows the generation of photon pairs. It is shown how the factorability of the created pairs depends on the fiber's dispersion properties, and the necessary conditions for the generation of factorable states are derived. The chapter concludes with an analysis of the photon statistics of the four-wave mixing process, explaining how statistics and the g(2) correlation function can be used to evaluate the factorability of the SFWM output state. Chapters 3 and 4 contain the main results of this thesis. Chapter 3 presents the first spectrally decorrelated photon-pair source bridging the visible and telecommunication wavelength ranges. The photon pairs are generated by SFWM in a photonic crystal fiber (PCF). The chapter documents the procedure of how the PCF source was designed and fabricated, as well as its characterization based on spectral measurements and photon statistics. One photon of the pair state is generated in the visible at 513.5 nm, where it can be efficiently detected with silicon-based single-photon detectors. It serves as a herald for its broadband partner photon, which is emitted in the telecom wavelength range at 1547 nm. A spectral coincidence measurement shows that the heralded photon exhibits a purity of up to 0.82. At increased pump powers, even the heralded generation of higher photon-number states in the telecom band becomes feasible. In Chapter 4, we use commercial birefringent fiber to herald high-purity photons of picosecond duration at 848 nm. The presented two-source HOM interference experiment shows that the heralded unfiltered state has a purity of at least 0.73. This value is increased to 0.84 with the application of wavelength filters suppressing low-intensity side peaks in the spectrum. The heralded photons are coupled into a single-mode fiber with an efficiency of 85%, the highest reported value to date for factorable sources. It is also shown that a commercial polarization controller can be used to fine-tune the generated wavelengths. This facilitates matching photons from multiple sources, as required for optical quantum computing schemes. Chapter 5 summarizes all results and provides an outlook toward potential future projects.
Single photon sources are a key element for quantum computing, quantum key distribution (QKD) and quantum communications. In particular, producing single photons at telecommunications wavelengths is valuable for QKD protocols and would enable realizing the quantum internet. The preferred method for their generation has long been spontaneous down conversion in bulk crystals, which suffers from connection loss to fiber networks. In-fiber spontaneous four-wave mixing provides a viable alternative as a photon pair source due to being compatible with existing fiber networks. We present an all-fiber photon pair source based on degenerate four-wave mixing in a 400 m Highly-Nonlinear fiber, with signal and idler wavelengths generated at 1552.5 nm and 1557 nm respectively. The source consists of CW pump laser operating at 1554.75 nm, which is slightly detuned from the zero group velocity dispersion wavelength into the normal dispersion regime. After pair generation in the highly-nonlinear fiber, three arrayed waveguide gratings are employed to spatially separate signal and idler, and provides a 120 dB pump power reduction. Firstly the source is modelled and experimentally characterized in the well known classical regime of stimulated four-wave mixing. The effect of fiber cooling on spontaneous Raman scattering is modelled and characterized, and a 30% reduction in spontaneous emission is found when cooling the fiber to -77°C. In the low power regime the coincidence to accidental count ratio is simulated and measured. An increase in the coincidence to accidental count ratio is observed when cooling the fiber.
A continuous-wave (CW) photon-pair source operating in the L-band was successfully realized based on spontaneous four-wave mixing (SFWM) by using short length of a birefringent ZBLAN fiber. A type-III phase-matched SFWM process was utilized by pumping a birefringent ZBLAN fiber with pump photons polarized along the slow axis, where signal and idler photons were generated with polarizations aligned to the vertical axis of the birefringent ZBLAN fiber. The phase-matching curve was calculated, and the joint spectral intensity was analyzed under 1310 nm pumping conditions. Then, we experimentally generated signal and idler photons with center wavelengths of 1117 and 1578 nm using a 1310 nm CW laser as a pump light source and measured their quantum optical properties. The maximum coincidence-to-accidental ratio was calculated to be 22, resulting in a photon-pair brightness of 3.16 × 10 4 pairs/s/nm/mW. The results show the feasibility of using ZBLAN fibers in quantum optics as an efficient platform for generating a quantum light source.
Quantum entanglement has been an extremely active field of research, both theoretically and experimentally. Studies on entanglement are fundamental to improving our basic understanding of quantum mechanics. As our understanding of the phenomenon grows, so does interest in using it to advance various technological fields: communications, computing, and sensing, to name just a few. It is now known that entangled photon pairs can be generated through a process known as Spontaneous Four-Wave Mixing (SFWM). In this paper, we report the generation of entangled photon pairs in time intervals by spontaneous four-wave mixing in a nonlinear fiber optic ring resonator. The requirements for efficient SFWM are quite similar to those for classical FWM, but they require even greater precision, especially for quantum applications. To achieve a measurable pair generation rate, a high-intensity pump laser is essential. The nonlinear medium must have high nonlinearity and confinement. This technique is compatible with contemporary fiber, enabling compact, low-cost, and scalable implementations such as quantum memories.
Q uantum entanglement refers to the nonclassical dependency of physically separated quantum systems. It is an essential resource that must be freely available for implementing many of the novel functions of quantum information processing, such as database searching, clock synchronization, teleportation, computing and cryptography.1 The efficient generation and transmission of quantum entanglement is therefore of prime importance. With the ubiquitous standard optical fiber serving as the transmission medium and the widespread availability of efficient active and passive fiber devices, technological synergy between the generation and propagation components of the overall quantum network can be achieved by deploying sources of entanglement that rely on the nonlinearity of the fiber itself. Such fiber-based sources of quantum entanglement would also have the advantage of modal purity over their crystal counterparts,2,3 which is very important for realizing complex networks that involve many quantum operations. In our quest to develop fiber-based devices for quantum information processing, we have recently demonstrated an allfiber source of quantum-correlated photon pairs.4 The operating physical mechanism in this source is nondegenerate fourphoton mixing, wherein two pump photons scatter through the Kerr nonlinearity of the fiber to create simultaneous signal and idler photons. Our experiment is conducted near the zero-dispersion wavelength of standard dispersion-shifted fiber, where such scattering is enhanced owing to phase matching of the photon wave functions. It must be pointed out here that in a conventional wavelength-divisionmultiplexed classical optical communication line, one strives to suppress the fourphoton or four-wave mixing process, which otherwise causes cross talk between the wavelength channels and sets limits on the total data capacity of the communication line. In our experiment, the four-photon mixing takes place in a nonlinear-fiber Sagnac interferometer (NFSI), which we previously used to generate quantum-correlated twin beams in the fiber.5 The pump is a mode-locked train of ~3-ps-long pulses. The pulsed operation serves two important purposes: the NFSI amplifier can be operated at low average powers and the production of the signal/ idler fluorescence photons is confined to well-defined temporal windows, allowing use of a gated detection scheme to increase the signal-to-noise ratio. To measure the nonclassical (i.e., quantum) correlations between the signal and the idler photons, one must effectively suppress the pump photons from reaching the detectors. Since a typical pump pulse contains ~108 photons and we are interested in detecting ~0.01 signal (idler) photons/pulse, a pump-to-signal (idler) rejection ratio in excess of 100 dB is required. We achieved this specification by sending the fluorescence photons through a free-space double-grating spectral filter that separates the signal and idler photons from each other and from the pump photons not rejected by the NFSI. To demonstrate the quantum nature of the four-photon scattering at the single photon level, we assembled a photonFigure 1.C oincidence rates as a function of the single-photon rates in two different cases: signalidler fluorescence produced by a pump pulse (diamonds) and signal-idler fluorescence produced by two consecutive pump pulses (triangles). T he line represents the calculated accidental counts. T he inset shows a plot of the detected idler photons as a function of the injected pump photons (hollow circles). A second-order polynomial is shown to fit the experimental data. T he contributions of the dark counts, linear scattering and quadratic scattering are plotted separately as well. counting apparatus for detecting the signal and idler photons in coincidence. This apparatus is based on commercial InGaAs avalanche photodiodes operating in the gated Geiger mode.4 In the inset in Fig. 1, we show the number of scattered photons, NS, versus the number of pump photons, NP, injected into the NFSI. We fit the experimental data with a second-order polynomial fit, including the number of dark counts during the gate interval, ND. The fit clearly shows that the quadratic scattering ( ∝NP) in the fiber can dominate over the residual linear scattering ( ∝NP) of the pump, owing to imperfect filtering. The main body of Fig. 1 shows the coincidence-counting results. The diamonds represent the rate of coincidence counts versus the rate of the signal (idler) photons generated during the same pump pulse. The triangles represent the measured coincidence rate versus the signalphoton count rate when the signal is delayed with respect to the idler by one pulse period. For two independent photon sources, each with a count rate RS <<1, the accidental coincidence rate RC is given by RC = RS 2, regardless of the photon statistics of the sources. This quadratic relation is plotted as the solid line in Fig. 1, which fits the delayed-coincidence data (triangles) very well. These measurements show that while the fluorescence photons produced by the adjacent pump pulses are independent, those coming from the same pump pulse show a strong correlation, which is a signature of their non-classical behavior. This work was supported by the Department of Defense Multidisciplinary University Research Initiative program administered by the Army Research Office under Grants DAAD19-00-1-0177 and DAAD19-00-1-0469, and by the U.S. Office of Naval Research under Grant N00014-91-J-1268.
The preparation of single photons in a pure quantum state is a subject of great interest in physics, enabling the control of light at an unprecedented level. The ease with which certain degrees of freedom of photon states, such as polarisation, can be manipulated, along with the inherent resilience of photons to decoherence, makes them well suited for use as qubits. Recent rapid developments in the transmission and processing of quantum information, as well as the likely technological impact of potential real-world applications such as quantum cryptography and quantum computation, mean that the demand for high performance single photon sources is likely to increase in the near future. One approach to producing single photon states, which are known to be in a well-defined spatio-temporal mode without destructively measuring them, is to take advantage of nonlinear optics. Nonlinear processes can be used to realise frequency conversion by generating a single, correlated pair of photons from an intense pump laser source. The detection of one of the photons from a pair can then be used to indicate the presence of the other photon in the pair, a procedure known as heralding. This thesis describes the development of a source of heralded single photons at 1550 nm, generated directly in the core of a photonic crystal fibre (PCF). By taking advantage of low loss fibre components for the required spectral filtering of the generated photon state, a heralding fidelity of 52% was achieved. The source was designed to be used with a picosecond pulsed fibre laser, making it relatively low cost and maintenance free. With 148 mW of average pump power a heralded output photon rate of 6.4 × 104 s-1 was observed, demonstrating the brightness of the source. The purity of the generated single photons was established by measuring non-classical interference, with a visibility of 70%, between the photons output from this source and a source based on a PPLN waveguide. The fabrication of a series of birefringent PCFs for the generation of spectrally pure state photons at 1550 nm is also discussed. These PCFs will be useful for incorporation in the next generation of high performance, fibre-based photon sources.